• Nuclear Engineering and Technology
• /
• v.2 no.3
• /
• pp.149-161
• /
• 1970

This paper describes a detailed investigational performance on the gamma radiation shield effect of heavy concretes that were manufactured by the use of mineral ores produced domestically and which may be possibly applied for the biological shield design. Ten different kinds of mineral ores were collected for use as the aggregates, physical test and chemical analysis for them were carried out to select the aggregate with a better property. Through the experimental investigation on the shielding effect of various concretes with different combination of concrete components such as water-cement and fine-coarse aggregate ratios, it was possible to derive some criteria for the best condition being capable of obtaining the concretes with high density and good uniformity. Data on the shielding-effectiveness of the different concretes were obtained by performing collimated beam experiment using 60Co gamma-ray. Analyzing the shielding-efficiency, shielding-concrete specific gravity and biological shield cost, the optimum condition of yielding the best economic shielding design, with low cost and good spatial distribution to some extent was determined.

• Journal of Korean Society of Water and Wastewater
• /
• v.14 no.1
• /
• pp.37-44
• /
• 2000

Laboratory experiments were conducted to investigate the performances of anaerobic filters packed with ceramic tube and pall-ring media treating a dairy waste. The media packing volume was 65% of effective volume of anaerobic filter. Organics removals of anaerobic filters were maintained above 80% even at an organics loading rate of $10kgCOD/m^3/d$, and this was comparable to aerobic treatment of organic wastes. Organics removals of the ceramic tube anaerobic filters were always lower than those of the pall-ring anaerobic filters due to intrinsic physical property of ceramic tube, especially lower void space which caused to clogging and entrapment of biogas, substrate transfer limitation, and irregular evolution of biogas leading to loss of solids and biomass. This was clearly observed in higher concentration of TSS in the effluent from the ceramic tube anaerobic filter despite of higher retention capacity of TSS compared with pall-ring media. Vertical distribution of organics and solids in the filters showed above 90% of organics and solids in influent were removed below 20% of reactor height, and 50% of remaining organics and solids were removed though media packing zone. Effluent quality from the anaerobic filter was heavily depended on media itself as well as suspended biomass formed below media. It is therefore concluded that the type of media played an important role in biomass accumulation arid gas-liquid-solid separation efficiency. Type of media did not affect the start-up behaviors of the anaerobic filter, and supernatant from anaerobic digested sludge showed a good performance as a seeding materials.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.6
• /
• pp.255-263
• /
• 2008

Generally, deposition mechanism of diamond particle is mainly embedding effect in the kinetic spray process. Accordingly, in spite of high cost, helium gas was employed as process gas to get high diamond fraction in the composite coating. In this study, the deposition behavior of bronze/diamond by kinetic spray process was compared using different process gas (helium and nitrogen). Bare (mean size of $5{\mu}m$, $20{\mu}m$) and nickel coated diamond (mean size of $26{\mu}m$) were deposited on Al 6061-T6 substrate with fixed process temperature and pressure. For comparison with experimental results, plastic deformation behavior of nickel layer was simulated by finite element analysis (using ABAQUS/Explicit 6.7-2). The size, broken ratio, and fraction of diamond in the composite coating were analyzed through scanning electron microscopy and image analysis method. The uniform distribution and deposition efficiency of diamond particles in the coating layer could be achieved by tailoring the physical properties of the feedstock.

• Korean Journal of Materials Research
• /
• v.22 no.8
• /
• pp.390-396
• /
• 2012

Ag pastes added to Bi-oxide frits have been applied to the electrode material of Si solar cells. It has been reported that frits induce contacts between the Ag electrodes and the Si wafer after firing. During firing, the control of interfaces among Ag, the glass layer, and Si is one of the key factors for improving cell performance. Specifically, the thermo-physical properties of frits considerably influence Ag-Si contact. Therefore, the thermal properties of frits should be carefully controlled to enhance the efficiency of cells. In this study, the interface structures among Ag electrodes, glass layers, and recrystallites on an $n^+$ emitter were carefully analyzed with the thermal properties of lead-free frits. First, a cross-section of the area between the Ag electrodes and the Si wafer was studied in order to understand the interface structures in light of the thermal properties of the frits. The depth and area of the pits formed in the Si wafer were quantitatively calculated with the thermal properties of frits. The area of the glass layers between the Ag electrodes and Si, and the distribution of recrystallites on the $n^+$ emitter, were measured from a macroscopic point of view with the characteristics of the frits. Our studies suggest that the thermophysical properties should be controlled for the optimal performance of Si solar cells; our studies also show why cell performance deteriorated due to the high viscosity of frits in Ag pastes.

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.6
• /
• pp.863-875
• /
• 2006

Intensive visibility monitoring was conducted to investigate physical and chemical characteristics of visibility impairment by airborne pollen. Light attenuation coefficients were optically measured by a transmissometer, a nephelometer, and an aethalometer. Elemental, ionic, and carbonaceous species were chemically analyzed on the filters collected by $PM_{2.5}$ and $PM_{10}$ samplers. Aerosol size distribution was analyzed using a cascade impactor during airborne pollen period. Airborne pollen count was calculated using a scanning electron microscope. Airborne pollen was emitted into the atmosphere in springtime and funker degraded visibility through its scattering and absorbing the light. Average light extinction coefficient was measured to be $211{\pm}36Mm^{-1}$ when airborne pollen was not observed. But it increased to $459{\pm}267Mm^{-1}$ during the airborne pollen period due to increase of average $PM_{2.5}$ and $PM_{10}$ mass concentration and relative humidity and airborne pollen count concentration for $PM_{10}$, which were measured to be $46.5{\pm}29.1{\mu}g\;m^{-3},\;97.0{\pm}41.7{\mu}g\;m^{-3},\;54.1{\pm}11.6%$, and $68.2{\pm}89.7m^{-3}$, respectively. Average light extinction efficiencies for $PM_{2.5}$ and $PM_{10}$ were calculated to be $5.9{\pm}0.9$ and $4.5{\pm}0.8m^2 g^{-1}$ during the airborne pollen period. Light extinction efficiency for $PM_{10}$ increased further than that for $PM_{2.5}$. The average light extinction budget by airborne pollen was estimated to be about 24% out of the average measured light extinction coefficient during the airborne pollen period.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.262-270
• /
• 2004

Basic experiments were carried out using the THT-IV low-power Hall thruster to examine the influences of magnetic field shape and strength, and acceleration channel length on thruster performance and to establish guidelines for design of high-performance Hall thrusters. Thrusts were measured with varying magnetic field and channel structure. Exhaust plasma diagnostic measurement was also made to evaluate plume divergent angles and voltage utilization efficiencies. Ion current spatial profiles were measured with a Faraday cup, and ion energy distribution functions were estimated from data with a retarding potential analyzer. The thruster was stably operated with a highest performance under an optimum acceleration channel length of 20 mm and an optimum magnetic field with a maximum strength of about 150 Gauss near the channel exit and with some shape considering ion acceleration directions. Accordingly, an optimum magnetic field and channel structure is considered to exist under an operational condition, related to inner physical phenomena of plasma production, ion acceleration and exhaust plasma feature. A new Hall thruster was designed with basic research data of the THT-IV thruster. With the thruster with many considerations, long stable operations were achieved. In all experiments at 200-400 V with 1.5-3 mg/s, the thrust and the specific impulse ranged from 15 to 70 mN and from 1100 to 2300 see, respectively, in a low electric power range of 300~1300 W. The thrust efficiency reached 55 %. Hence, a large map of the thruster performance was successfully made. The thermal characteristics were also examined with data of both measured and calculated temperatures in the thruster body. Thermally safe conditions were achieved with all input powers.

• Korea Journal of Hospital Management
• /
• v.4 no.2
• /
• pp.266-285
• /
• 1999

The purpose of this study is to identify influencing factors for successful introduction, implementation and management of HMRPS through assessment of the employees attitude toward HMRPS in technical, administrative, and organization behavioral areas. Data were collected from 157 HMRPS employee members' self-reporting questionnaire in three university hospitals in the city of Seoul and Kyonggi Province from November 5 to November 10, 1997. Relevant literature on industry company MPR system theory was reviewed to develop the theoretical framework. The results were as follows: The employee's recognition of tangible benefit were more significantly influenced success than intangible benefit for successful operation relating the HMRPS. Concerning the employee's recognition of the successful HMRPS and the factor of influenced success was significantly positive correlation between tangible and intangible benefits and success factor in technical, administrative, and organizational behavior area. This study showed that major factor affecting the employee's recognition of tangible and intangible benefit for successful HMRPS. For tangible benefits; Success factors in the technical areas were quality of the data and information, efficiency of inventory management and rescheduling of operation plan. Success factors in the administrative areas were: role of top management. Success factors in the organization behavioral areas were; simplicity of the HMRPS, human resistance to change. For intangible benefits; Success factors in the organization behavioral areas were; user involvement, simplicity of HMRPS, human resistance to change. Futhermore as the exact evaluation of successful factors of HMRPS implement is needed, research for the development of systemic variables of physical distribution system control, methods, capacity of system, duration and other environment in many of 30 hospitals or more, and for the empirical study for HMRPS.

• Journal of the Korean Society for Library and Information Science
• /
• v.43 no.3
• /
• pp.59-84
• /
• 2009

In the context of the knowledge and information society, social capital has been considered significantly in conjunction with human and physical capital. Social capital contains the social capacity which is beneficial to the efficiency and associated capital of social policies. This study aims to examine the strategic plans in order to establish researcher information systems in terms of research and development, and researcher resources at the national level. To achieve the goals of this study, firstly the current status of researcher information systems in Korea was examined. The analysis of researcher information systems includes information systems in the national R&D management institutes, the national distribution institutes, and the government funded research centers. Secondly, strategic plans for researcher information systems as social capital were discussed.

• Korean journal of applied entomology
• /
• v.60 no.2
• /
• pp.247-254
• /
• 2021

An outbreak of the onion thrips, Thrips tabaci, was observed in welsh onion cultured in greenhouse during winter season (Jan ~ Feb). The thrips was identified using DNA barcode. Weekly occurrence was around 240 ~ 700 adults per trap. Trap color gave significant influence on the capture efficiency with a preference on yellow compared to blue sticky trap. Subsequently, most (> 90%) onions exhibited a damage symptom induced by the thrips. This outbreak was observed only in a specific area but not in nearby greenhouses. This discontinuous occurrence pattern was further investigated by analyzing flight behavior through in- and out- door tests. About 1.5 mm-body length adults could jump up to about 5 cm and fly up to 2 m in altitude, which was the top of the greenhouse. This suggested their migrating potential to nearby (< 2 m) greenhouses. However, few were detected in the neighboring places probably due to physical hindrance with low temperatures between greenhouses. This is reasoned why the onion thrips forms a patch distribution among greenhouses during winter season.

• Particle and aerosol research
• /
• v.18 no.4
• /
• pp.129-136
• /
• 2022

The line width of circuits in semiconductor devices continues to decrease down to a few nanometers. Since nanoparticles attached to the patterned wafer surface may cause malfunction of the devices, it is crucial to remove the contaminant nanoparticles. Physical cleaning that utilizes momentum of liquid for detaching solid nanoparticles has recently been tested in place of the conventional chemical method. Dropwise impaction has been employed to increase the removal efficiency with expectation of more efficient momentum exchange. To date, most of relevant studies have been focused on drop spreading behavior on a horizontal surface in terms of maximum spreading diameters and average spreading velocity of drop. More important is the local liquid velocity at the position of nanoparticle, very near the surface, rather than the vertical average value. In addition, there are very scarce existing studies dealing with microdroplet impaction that may be desirable for minimizing pattern demage of the wafer. In this study, we investigated the local velocity distribution in spreading liquid film under various impaction conditions through the CFD simulation. Combining the numerical results with the particle removal model, we estimated an effective cleaning diameter (ECD), which is a measure of the particle removal capacity of a single drop, and presented the predicted ECD data as a function of droplet's velocity and diameter particularly when the droplets are microns in diameter.