• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.99-100
• /
• 2019

Water repellent and waterproofing agents fail to act work properly if cracks or detachment occurs outside. The method of making mortar was tested by classifying it into two methods: direct water-repellent put in concrete and water-repellent spray to sand method. It was found that the compressive strength was decreased as the amount of water repellent was increased. As a result of measuring the contact angle, all of the specimens were hydrophobic. The spray method showed greater water repellent effect than the direct mixing method.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.18 no.6
• /
• pp.215-226
• /
• 2015

This study introduced food waste into re-vegetation base materials for surface loss recovery of carry-away highway cut slope. The object of this study is to derive the mixing ratio of food waste by conducting a test installation, monitoring, analysis and evaluation for recovery of carry-away highway cut slope. The following items were investigated and analyzed each experimental zone to draw mixing ratio of re-vegetation base materials and food waste : the physical and chemical properties of the vegetation base materials, soil-hardness, soil-humidity, left out and the collapsed point, established number of trees, species richness of grass species and tree species, coverage, pest status, and invasion of disturbance species. The re-vegetation method was evaluated by each experiment zone which has different mixing ratio. As a result, experiment zone A was rated 45 points out of 60 rating points as the best re-vegetation method. However, this study result has been derived from one construction and short-term monitoring. In order to derive the suitable and dependable mixing ratio, conducting an objective re-vegetation method evaluation and long-term experiment and monitoring is required.

• Computers and Concrete
• /
• v.31 no.6
• /
• pp.501-511
• /
• 2023

The strengthening efficiency of biopolymer treated soil depends on biopolymer type, concentration ratio, soil type, initial water content, curing time and mixing method. In this study, the physical and mechanical properties of xanthan gum (XG) treated kaolinite were investigated through compaction test, Atterberg limit test, triaxial test and unconfined compression test. The results indicated that the optimum water content (OWC) increased from 30.3% of untreated clay to 33.5% of 5% XG treated clay, while the maximum dry density has a slight increase from 13.96 kg/m³ to 14 kg/m³ of 0.2% XG treated clay and decrease to 2.7 kg/m³ of 5% XG treated clay. Meanwhile, the plastic limit of XG treated clay increased with the increase of XG concentration, while 0.5% XG treated clay can be observed the maximum liquid limit with 79.5%. Moreover, there are the ideal water content about 1.3-1.5 times of the optimum water content achieving the maximum dry density and curing time to obtain the maximum compressive strength for different XG contents, which the UCS is 1.52 and 2.07 times of the maximum UCS of untreated soil for 0.5% and 1% XG treated clay, respectively. In addition, hot-dry mixing can achieve highest UCS than other mixing methods (e.g., dry mixing, wet mixing and hot-wet mixing).

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.19 no.4
• /
• pp.45-59
• /
• 2016

This study introduced wood waste into revegetation base materials for recovery of highway cut slope. The object of this study is to derive the mixing ratio of wood waste, kaoline and silica by conducting a test installation, monitoring, analysis and evaluation. The following items were investigated and analyzed each experimental zone to deduce the mixing ratio of wood waste, kaoline and silica on slope revegetation base materials: the physical and chemical properties of the vegetation base materials, soil-hardness, soil-humidity, collapse and eroded spots, established number of trees, existing species of grass and tree species, vegetation coverage ratio, pest status, and invasion of disturbance species. The revegetation method was evaluated in each experiment zone which had different mixing ratios. As a result, experiment zone C scored 47 points out of 60 as the best revegetation method. However, this result has been derived from just one construction and short-term monitoring. In order to derive the suitable and dependable mixing ratio, conducting an objective revegetation method evaluation and long-term experimenting and monitoring is required.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.219-219
• /
• 2006

This study focuses on the effects of dispersion method of a nanoparticle in a polymer matrix such as melt mixing, solution blending, and in-situ polymerization on the physical properties of the nanocomposites. Introduction of a nanoparticle to a polymer resulted in some unusual physical properties. In some cases the nanoparticle played a role of a nucleating agent, leading to decreasing induction time to crystallization. In addition, the dispersion state of the nanoparticle in the polymer matrix also had a significant influence on the physical properties of the nanocomposites. Hence the method of introducing the nanoparticle to the polymer made contribution to the rheological properties of the nanocomposite systems.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.2
• /
• pp.97-104
• /
• 2005

A simple but efficient grid generation technique by using the modified compressible form of stream function has been formulated. Transformation of a physical plane to a streamline plane, the Von Mises Transformation, has been widely used to solve the differential equations governing flow phenomena, however, limitation arises in low velocity region of boundary layer, mixing layer and wake region where the relatively large grid spacing is inevitable. Modified Von Mises Transformation with simple mathematical adjustment for the stream function is suggested and applied to solve the confined coaxial turbulent jet mixing with simple $\kappa-\epsilon$ turbulence model. Comparison with several experimental data of axial mean velocity, turbulent kinetic energy, and Reynolds shear stress distribution shows quite good agreement in the mixing layer except in the centerline where the turbulent kinetic energy distributions were somewhat under estimated. This formulation is strongly suggested to be utilized specially for free turbulent mixing layers in axisymmetric flow conditions such as the investigation of mixing behavior, jet noise production and reduction for Turbofan engines.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1992.10a
• /
• pp.47-54
• /
• 1992

When marine clay is hydraulically dredged from seabed and pumped into the pond enclosed by contatinment dykes, marine clay is mixed and flocculated with water and then settled. At this time, the fines will interact with the water to form a Bingham plastic slurry which has non-Newtonian characteristics. The dredged slurry has different physical properties depending on settling locations and settling depths in the pond and has few hundred percent of water content and almost nil of shear strenght. In order to make this condition of the dredged slurry the final formation for public use within a short period, sand spreading method to enhance the support capacity of the dredged slurry is developed. In this paper, the effect of sand mixing into the dredged slurry of this method is analyzed based on reference study, laboratory tests and actual construction results.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.793-808
• /
• 2009

This paper presents procedure and prediction method of internal and external stabilities when designing D.C.M, with main factors to be considered, such as chemical reaction of additive, physical properties of stabilized body and mixing strength. Results show that through case studies, a design unconfined compressive strength of stabilized body (hereafter referred to as 'compressive strength') directly depends on the quantity of cement, which is decided by laboratory test, and the compressive strength enormously affects internal and external stabilities. So laboratory mixing test to obtain the compressive strength for design allowable stress should be given careful considerations.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.5
• /
• pp.15-24
• /
• 2022

In order to improve dredged area, long time and high cost is needed because of bad engineering and physical conditions. And there is no suitable example of pipe mixing method at domestic site. Moreover, applicability and effectiveness of this method is uncertain and shows different results between site and laboratory test. In order to solve these problems, we determined proper grain size distribution and water content range using dredged soil and reformed material (standard sand & material controlling grain size distribution) in the laboratory test. As a result, we confirmed that coefficient of sediment consolidation is increased and there is an improvement about separation sedimentation. Undrained shear strength was derived by water content of reformed dredging soil through regression analysis of test results. We suggest the correlation equation for determining mixing ratio.

• Journal of Hydrogen and New Energy
• /
• v.22 no.2
• /
• pp.249-256
• /
• 2011

In this study, the Ni-based catalysts for the production of synthetic natural gas were prepared by various preparation methods such as the co-precipitation, precipitation, impregnation and physical mixing methods. The ranges of the reaction conditions were the temperatures of 250~$350^{\circ}C$, $H_2$/CO mole ratio of 3.0, the pressures of 1 atm and the space velocity of 20000 $ml/g_{-cat{\cdot}}{\cdot}h$. It was found that the catalyst prepared by precipitation method had higher CO conversion than the catalyst prepared by co-precipitation method. While the catalyst prepared by precipitation method had the formation of NiO structure, the catalyst prepared by co-precipitation method had the formation of $NiAl_2O_4$ structure. It was confirmed that Ni-based catalyst prepared by the physical mixing method had the lowest CO conversion because it was deactivated by the production of $Ni_3C$ during the methanation. As a result, it was shown clearly that Ni-based catalysts prepared by impregnation method expressed the highest catalytic activity in CO methanation.