• Journal of Electrochemical Science and Technology
• /
• 제2권2호
• /
• pp.68-75
• /
• 2011

In this review, we have investigated the effect of $TiO_2$-based blocking layers (t-BLs), deposited on a transparent conductive oxide (TCO)-coated glass substrate, on the photovoltaic performance of dye-sensitized solar cells (DSSCs). The t-BL was deposited using spin-coating or sputtering technique, and its thicknesses were varied to study the influence of the thin $TiO_2$ layer in between transparent conducting glass and nanocrystalline $TiO_2$ (nc-$TiO_2$). The DSSC with the t-BL showed the improved adhesion and the suppressed charge recombination at a TCO glass substrate than those without the t-BL, which led to the higher conversion efficiency.

• 한국진공학회지
• /
• 제16권3호
• /
• pp.161-166
• /
• 2007

태양광발전이란 태양에너지를 직접 전기 에너지로 변환시키는 것이다. 지난 5년 동안 태양광발전은 세계적으로 높은 성장률을 보여 왔다. 특히 2006년에는 30%, 이상의 성장을 가져왔으며 앞으로 20년 동안 평균 생산 성장률은 매년 27%-34%가 될 것으로 예상하고 있다. 현재까지는 태양광발전을 이용해 생산된 전력의 가격은 기존 전력발전의 가격보다 높지만 태양광 기술의 발전과 효율의 향상으로 점점 그 가격이 떨어지고 있다. 뿐만 아니라 태양전지용의 실리콘 기판의 대량생산은 점점 더 태양전지의 가격 저하를 가져오고 있다. 태양전지의 변화효율의 한계는 30%이다. 현재에는 결정질 실리콘 태양전지가 주를 이루고 있지만 미래에는 박막 실리콘 태양전지가 주도를 이룰 것이다. 2030년에는 박막 태양전지가 90%이상을 이루고 결정질 태양전지는 10% 이하로 떨어질 것을 예상하고 있다. 성균관대학교에서는 결정질 실리콘 태양전지의 저가화와 고효율화를 주 연구로 수행하고 있다. 현재 성균관대학교에서는 스크린 프린트를 이용해서 16% 이상의 다결정 실리콘 태양전지와 17% 이상의 단결정 실리콘 태양전지를 성공적으로 제작하였다. 제 1세대에서 다음 세대의 태양전지 발전의 과정은 새로운 접근법으로 확대되지만 여전히 실리콘이 지금까지 주된 재료로 쓰이고 있다. 2010년까지 이러한 기술들에 대한 격차는 여전히 있지만 태양광발전을 통한 전력생산의 가격은 60 cent/watt 정도로 예상하고 있다. 태양광발전은 청정에너지로서 재생불가능 하고 고갈되어가고 환경오염을 일으키는 다른 에너지와 비교하여 점점 대체에너지로서의 자리를 확립해 가고 있다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.180-182
• /
• 2009

Two different wet etching solutions, NaOH 40% and Acid, were used for etching in tri-crystalline Silicon(Tri-Si) solar cell fabrication. The wafers etched in NaOH40% solution showed higher reflectance compared to the wafers etched in Acid solution after $SiN_x$ deposition. In light current-voltage results, the cells etched in Acid solution exhibited higher short circuit current and open circuit voltage than those of the cells etched in NaOH 40% solution. We have obtained 16.70% conversion efficiency in large area($156cm^2$) Tri-Si solar cells etched in Acid solution.

• 한국태양에너지학회 논문집
• /
• 제29권5호
• /
• pp.14-19
• /
• 2009

The 50 kWp grid connected photovoltaic system which was installed at KEPRI site in 1999 has been operated more than 10 years. In order to acquire long term operation characteristics of medium size photovoltaic system, the operation test data related on power generation electricity and capacity factor of 50 kWp system, which have been collected since 1999, were analysed. From the analysing results, 57.7 MWh in annual power generation electricity of 50 kWp photovoltaic system in 1999 has been decreased 49.1 MWh in 2005 and reached 41.9 MWh in 2008. In addition to, the capacity factor of 50 kWp photovoltaic system also showed 13.2 % in 1999, 11.2% in 2005 and finally reached 9.6% in 2008. The operation test data showed a trend of decreasing of generation electricity and capacity factor during the 10 years operation time and we guessed that was caused by solar cell performance degradation and decreasing of PCS system efficiency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1592-1594
• /
• 2003

This paper presents the deposition and characterization of microcrystalline silicon(${\mu}c$-Si:H) films by HWCVD(Hot-wire Chemical Vapor Deposition) method at low substrate($300^{\circ}C$). The filament temperature, pressure and $SiH_4$ concentration were determined to be a critical parameter for the deposition of poly-Si films. Series A was deposited under the conditions of $1380^{\circ}C$(Tf), 100 mTorr and $2{\sim}10%\{SC:SiH_4/(SiH_4+H_2)\}$ for 60 min. Series B was deposited under the conditions of $1400{\sim}1450^{\circ}(T_f)$, 30 mTorr and $2{\sim}12%$(SC) for 60 min. The physical characteristics were measured by Raman and FTIR spectroscopy, dark and photoconductivity measurements under AM1.5 illumination.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1598-1600
• /
• 2003

Microcrystalline silicon(c-Si:H) thin-film solar cells are prepared with intrinsic Si-layer by hot wire CVD. The operating parameters of solar cells are strongly affected by the filament temperature ($T_f$) during intrinsic layer. Jsc and efficiency abruptly decreases with elevated $T_f$ to $1400^{\circ}C$. This deterioration of solar cell parameters are resulted from increase of crystalline volume fraction and corresponding defect density at high $T_f$ The heater temperature ($T_h$) are also critical parameter that controls device operations. Solar cells prepared at low $T_h$ (<$200^{\circ}C$) shows a similar operating properties with devices prepared at high $T_f$, i.e. low Jsc, Voc and efficiency. The origins for this result, however, are different with that of inferior device performances at high $T_f$. In addition the phase transition of the silicon films occurs at different silane concentration (SC) by varying filament temperature, by which highest efficiency with SC vanes with $T_f$.

• Electronic Materials Letters
• /
• 제14권6호
• /
• pp.712-717
• /
• 2018

In this letter, we have introduced copper chloride ($CuCl_2$) as an additive in the $CH_3NH_3PbI_3$ precursor solution to improve the surface morphology and crystallinity of $CH_3NH_3PbI_3$ films in a single solvent system. Our optimized perovskite solar cells (PSCs) with 2.5 mol% $CuCl_2$ additive showed best power conversion efficiency (PCE) of 15.22%. The PCE of the PSCs fabricated by $CuCl_2$ (2.5 mol%) additive engineering was 56% higher than the PSC fabricated with pristine $CH_3NH_3PbI_3$.

• 한국전기전자재료학회논문지
• /
• 제36권5호
• /
• pp.442-453
• /
• 2023

Tandem or multijunction solar cells (MJSCs) can convert sunlight into electricity with higher efficiency (η) than single junction solar cells (SJSCs) by dividing the solar irradiance over sub-cells having distinct bandgaps. The efficiencies of various common SJSC materials are close to the edge of their theoretical efficiency and hence there is a tremendous growing interest in utilizing the tandem/multijunction technique. Recently, III-V materials integration on a silicon substrate has been broadly investigated in the development of III-V on Si tandem solar cells. Numerous growth techniques such as heteroepitaxial growth, wafer bonding, and mechanical stacking are crucial for better understanding of high-quality III-V epitaxial layers on Si. As the choice of growth method and substrate selection can significantly impact the quality and performance of the resulting tandem cell and the terminal configuration exhibit a vital role in the overall proficiency. Parallel and Series-connected configurations have been studied, each with its advantage and disadvantages depending on the application and cell configuration. The optimization of both growth mechanisms and terminal configurations is necessary to further improve efficiency and lessen the cost of III-V on Si tandem solar cells. In this review article, we present an overview of the growth mechanisms and terminal configurations with the areas of research that are crucial for the commercialization of III-V on Si tandem solar cells.

• ETRI Journal
• /
• 제42권1호
• /
• pp.118-128
• /
• 2020

A semitransparent photovoltaic-thermal (PV/T) air collector can produce electricity and heat simultaneously. To maximize the thermal and overall efficiency of the semitransparent PV/T air collector, its availability should be maximum; this can be determined through a Markov analysis. In this paper, a Markov model is developed to select an optimized number of semitransparent PV modules in service with five states and two states by considering two parameters, namely failure rate (λ) and repair rate (μ). Three artificial neural network (ANN) models are developed to obtain the minimum cost, minimum temperature, and maximum thermal efficiency of the semitransparent PV/T air collector by setting its type appropriately and optimizing the number of photovoltaic modules and cost. An attempt is also made to achieve maximum thermal and overall efficiency for the semitransparent PV/T air collector by using ANN after obtaining its minimum temperature and available solar radiation.

• Transactions on Electrical and Electronic Materials
• /
• 제15권4호
• /
• pp.217-220
• /
• 2014

We studied the plating properties of Sn-Pb solder according to the shape of the Cu wire's cross-section for photovoltaic ribbon. The thickness of the Sn-Pb layer largely decreased to 29% on a curved Cu surface, compared to a flat Cu surface. This phenomenon is caused by the geometrical decrease in the contact angle of the liquid Sn-Pb solder and an increase in the surface energy of the solid/vapor on the curved Cu surface. We suggest a new ribbon's design where the Cu wire's cross-section is a semi-ellipse. These semi-ellipse ribbons can decrease the use of Sn-Pb solder to 64% and increase the photovoltaic efficiency, by reducing the contact area between the ribbon and cell, to 84%. We also see an improvement of reflectivity in the curved surface.