• Korean Journal of Materials Research
• /
• v.17 no.12
• /
• pp.676-681
• /
• 2007

According to progress rapidly digitalization, networked and mobilization of electronics industry, there are demands for being smaller, thinner, more light, and more efficient complex functions of electronic devices which are wireless devices, semi-conductors, packages and mobile devices. Therefore, the solder resist on a printed circuit board have been required with the high resolution and the eco-friendly materials in the surface treatments such as high heating process and coating process with electrolysis. In this study, the photoinitiator initiator and monomers of the solder resist were prepared with their contents for reducing the occurrence of the under-cut. We investigated the sample surface by UV/VIS spectrometer, FT-IR, OM after HASL and ENIG process. From our results, it is possible to get a high adhesion of resist with optimal contents between the photoinitiator initiator and monomers after surface treatments.

• Journal of the Korean Applied Science and Technology
• /
• v.17 no.3
• /
• pp.192-197
• /
• 2000

Rosin moeity-containing monomer was prepared by the reaction of abietic acid with 2-hydroxyethyl methacrylate in tetrahydrofuran(THF) using diethyl azodicarboxylate as a catalyst. This new monomer was photo-polymerized to give thin films in the presence of a radical type initiator. The rate of photo-polymerization and amount of cured polymer were determined using the residual yield method. A thermogravimetric analysis of the cured polymer showed that the film was stable up to 170oC, at which point the polymer film has lost 10 wt % of its weight.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.1
• /
• pp.35-41
• /
• 2014

UV curable transparent hard coating materials have been developed to improve the mechanical and optical properties of PET substrate. The coating materials were synthesized using various urethane acrylate oligomers, monomers, photo initiators, and leveling agents. The materials were coated on PET substrates and UV cured. The hard coated PET films were shown to have the good scratch resistance and transparency. When the urethane acrylate oligomer with more functional groups was introduced into the coating solution, the mechanical and optical properties were improved. However the higher concentration of 9-functional oligomer resulted in the decrease of workability. The addition of trimethylolpropane ethoxylate$(EO/OH)_9$ triacrylate(TMPETA) to coating solution improved the workability and properties. As a result, the UV cured film from the formulation of urethane acrylate oligomer with 9-functional groups, TMPETA as a monomer, IRACURE 754 as a photo initiator and BYK-340 as a leveling agent showed the best mechanical and optical properties in this study.

• Macromolecular Research
• /
• v.14 no.3
• /
• pp.324-330
• /
• 2006

Four different molecularly imprinted polymers (MIPs) were prepared using resveratrol as the template, methacrylic acid (MAA) or acrylamide (AA) as functional monomers, 2,2-azobisisobutyronitrile (AIBN) as the initiator, and thermo- or photo-induced polymerization. The ability of the different polymers to rebind selectively not only the template but also other phenols was evaluated. In parallel, the influence of the different templates and functional monomers used during polymer syntheses on the performance of the obtained MIPs was also studied through different rebinding experiments. The binding ability and selectivity of the polymer were studied by static balance method and Scatchard analysis. It was concluded that AA-based polymer by photo-induced polymerization presents the best properties to be used as a selective absorbent for the extraction of resveratrol.

• Tribology and Lubricants
• /
• v.36 no.5
• /
• pp.267-273
• /
• 2020

This study experimentally investigates hydrophobic surfaces fabricated via additive manufacturing. Additive manufacturing, commonly known as 3D printing, is the process of joining materials to fabricate parts from 3D model data, usually in a layer-upon-layer manner. Digital light processing is used to fabricate hydrophobic surfaces in this study. This method uses photo-curable resins and ultraviolet (UV) sources. Moreover, this technique generally has faster shaping speeds and is advantageous for the fabrication of small components because it enables the fabrication of one layer at a time. Two photo-curable resins with different compositions are used to fabricate micro-patterns of hydrophobic surfaces. The resins are composed of a photo-initiator, monomer, and oligomer. Experiments are conducted to determine suitable process conditions for the fabrication of hydrophobic surfaces depending on the type of resin. The most important factors affecting the process conditions are the UV exposure time and slice thickness. The fabrication capability according to the process conditions is evaluated using the side and top views of the micro-patterns observed using a microscope. The micro-patterns are collapsed and intertwined when the exposure time is short because sufficient light (heat) is not applied to cure the photo-curable resin with a given slice thickness. On the other hand, the micro-patterns are attached to each other when the exposure time is prolonged because the over-curing time can cure the periphery of a given shape. When the slice is thicker, the additional curing area is enlarged in each slice owing to the straightness of UV light, and the slice surface becomes rough.

• Journal of the Optical Society of Korea
• /
• v.10 no.1
• /
• pp.1-10
• /
• 2006

Optical transparency and high diffraction efficiency are two essential factors for high performance of the photopolymer. Optical transparency mainly depends on the miscibility between polymer binder and photopolymerized polymer, while diffraction efficiency depends on the refractive index modulation between polymer binder and photopolymerized polymer. For most of organic materials, the large refractive index difference between two polymers accompanies large structural difference that leads to the poor miscibility and thus poor optical quality via light scattering. Therefore, it is difficult to design a high-performance photopolymer satisfying both requirements. In this work, first, we prepared a new phase-stable photopolymer (PMMA) with large refractive index modulation and investigated the optical properties. Our photopolymer is based on modified poly (methyl methacrylate) as a polymer binder, acryl amide as a photopolymerizable monomer, triethanolamine as initiator, and yellow eosin as a photosensitizer at 532 nm. Diffraction efficiency over 85% and optical transmittance over 90% were obtained for the photopolymer. Second, Organic-inorganic nanocomposite films were prepared by dispersing an aromatic methacrylic monomer and a photo- initiator in organic-inorganic hybrid sol-gel matrices. The film properties could be controlled by optimizing the content of an organically modified silica precursor (TSPEG) in the sol-gel matrices. The photopolymer film modified with the organic chain (TSPEG) showed high diffraction efficiency (> 90%) under an optimized condition. High diffraction efficiency could be ascribed to the fast diffusion and efficient polymerization of monomers under interference light to generate refractive index modulation. The TSPEG modified photopolymer film could be successfully used for holographic memory.

• Korean Journal of Optics and Photonics
• /
• v.21 no.1
• /
• pp.6-11
• /
• 2010

Fluorescent photopolymer film was prepared with composition containing acrylate monomer, binder, a visible light sensitive photo initiator, and fluorescent anthracene polymer. A fluorescent grating pattern was inscribed on the photopolymer film using a 2-beam coupling method. A 514 nm laser was coupled to generate a beam-interference pattern. A highly fluorescent diffractive line pattern was formed on the fluorescent photopolymer within 30 sec. of exposure. The fluorescence intensity was highly enhanced in the patterned area, possibly due to the change in the environment of the fluorescent polymers by the photo-polymerization of monomers. Under a photo-mask, a gap electrode pattern was formed of fluorescent gratings with a sub-micron scale, which was matched well to the calculated value ($2.5\;{\mu}m$ and $0.6\;{\mu}m$) based on the refractive index of the photopolymer and beam incident angle ($3.4^{\circ}$, $15^{\circ}$) to the photopolymer surface.

• Analytical Science and Technology
• /
• v.17 no.3
• /
• pp.225-229
• /
• 2004

The effect of the silicon acrylate as a reactive additive on the UV-curing photopolymerization reaction was studied by micro raman technique. For the study, acrylate systems and Darocur 1173 were used as oligomer and monomers, and a photo initiator, respectively. The content of silicon acrylate was within the range of 0-3 wt%. The extent of photo-polymerization reaction as a function of depth from the air interface was obtained from the conversion ratio of acrylate double bond calculated from the intensities of measured bands at $1410cm^{-1}$ and at $1635cm^{-1}$. Micro raman spectroscopic technique can be an useful tool for the investigation of the factors, which can affect the reaction progress, such as oxygen inhibition, composition of the formulations, depth, etc.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.442-446
• /
• 2007

Alkali soluble and photo-curable polyesters were prepared from fluorene epoxy acrylate and various aromatic dianhydrides. To make a black matrix for LCD color-filter application, photo-resist solution was made by mixing synthesized polyester as binder, carbon black as pigment, initiator and multifunctional monomer in solvent. Black matrix pattern was formed on the glass substrate by lithography process. In this study, we synthesized various polyester-based binder polymers for LCD color-filter applications, and compared the analytical properties of those polymers and lithography patterns.

• Journal of Technologic Dentistry
• /
• v.35 no.4
• /
• pp.313-320
• /
• 2013

Purpose: The purpose of this study was to know the physical properties of UDMA dental composite resins containing two photosensitizers, PD, DA, as a photosensitizer instead of CQ. We want to know Remaining Double Bond(RDB) of UDMA unfilled resin and diametral tensile strength and flexural strength of composite resin containing PD and DA were compared with those of CQ, most widely used photosensitizer for dental composite resins. Methods: The RDB of UDMA studied by FT-IR spectroscopy increased with irradiation time. The composite resins were tested for their physical properties. The dental composite resins were made with UDMA as a monomer, silanized silica as filler, N,N-dimethylaminoethyl methacrylate (DAEM) as amine initiator, and one of the two kinds of new photosensitizers. Results: The relative RDB of UDMA was in the order: DA > CQ > PD but the physical properties of the composite resins show PD and DA with higher results compared with that containing CQ. The reason for the results is that PD and DA serve not only as a photosensitizer but also as a photo-crosslinking agent. Conclusion: PD and DA show as effective photosensizers, suitable for UDMA dental composite resin compare with a higher efficiency than CQ.