• Journal of the Mineralogical Society of Korea
• /
• v.27 no.4
• /
• pp.223-233
• /
• 2014

Cyanidation method has been used to extract high-purity gold and silver in mining industry. Such mining activities have used a large amount of cyanide, and the mine wastewater contained a high level of cyanide has brought about pollution of surrounding aqueous environments. This research was initiated to study $TiO_2$-catalytic UV-LED photo-oxidation to remove cyanide from the mine wastewater. UV lamp has been generally used as a light source in conventional photo-oxidation so far, but it shows numerous drawbacks. For this reason, this study focused on the evaluation of applicability of UV-LED as an alternative light source in cyanide photo-oxidation process. Three types of $TiO_2$ photo-catalyst were compared in terms of performance of photo-oxidation of cyanide, and the results show that Degussa P25 was the most efficient. In addition, four types of UV-LED were tested to compare their efficiencies of cyanide photo-oxidation, and their efficacy was increased in the order of 365 nm lamp-type > 365 nm can-type > 280 nm can-type > 420 nm lamp-type. Not only did this study demonstrate that UV-LED can be used in the photo-oxidation of cyanide as an alternative light source of UV lamp, but also confirmed that the performance of photo-oxidation was significantly influenced by the type of $TiO_2$ catalysts.

• Journal of Environmental Science International
• /
• v.21 no.4
• /
• pp.411-419
• /
• 2012

In this study, Ibuprofen (IBP) degradation by the photo catalytic process was investigated under various parameters, such as UV intensity, optimum dosage of $TiO_2$, alkalinity, temperature and pH of bulk solution. The pseudo-first order degradation rate constants were in the order of $10^{-1}$ to $10^{-4}min^{-1}$ depending on each condition. The Photocatalytic IBP degradation rate increased with an increase in the applied UV power. At high UV intensity a high rate of tri-iodide ($I_3{^-}$) ion formation was also observed. Moreover, in order to avoid the use of an excess catalyst, the optimum dosage of catalyst under the various UV intensities (30 and 40 W/L) was examined and ranged from approximately 0.1 $gL^{-1}$. The photo catalytic IBP degradation rate was changed depending on the alkalinity and temperature and pH in the aqueous solution. This study demonstrated the potential of photo catalytic IBP degradation under different conditions.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.3
• /
• pp.156-159
• /
• 2013

The electrical properties of ZnO nanowire field effect transistors (FETs) have been investigated depending on various diameters of nanowires. The ZnO nanowires were synthesized with an Au catalyst on c-plane $Al_2O_3$ substrates using hot-walled pulsed laser deposition (HW-PLD). The nanowire FETs are fabricated by conventional photo-lithography. The diameter of ZnO nanowires is simply controlled by changing the thickness of the Au catalyst metal, which is confirmed by FE-SEM. It has been clearly observed that the ZnO nanowires showed different diameters simply depending on the thickness of the Au catalyst. As the diameter of ZnO nanowires increased, the threshold voltage of ZnO nanowires shifted to the negative direction systematically. The results are attributed to the difference of conductive layer in the nanowires with different diameters of nanowires, which is simply controlled by changing the catalyst thickness. The results show the possibility for the simple method of the fabrication of nanowire logic circuits using enhanced and depleted mode.

• Carbon letters
• /
• v.18
• /
• pp.30-36
• /
• 2016

Well-dispersed Ag₃VO₄ nanoparticles @polyacrylonitrile (PAN) nanofibers were synthesized by an easily controlled, template-free method as a photo-catalyst for the degradation of methylene blue. Their structural, optical, and photocatalytic properties have been studied by X-ray diffraction, transmission electron microscopy, field-emission scanning electron microscopy equipped with rapid energy dispersive analysis of X-ray, photoluminescence, and ultraviolet-visible spectroscopy. The characterization procedures revealed that the obtained material is PAN nanofibers decorated by Ag₃VO₄ nanoparticles. Photocatalytic degradation of methylene blue investigated in an aqueous solution under irradiation showed 99% degradation of the dye within 75 min. Finally, the antibacterial performance of Ag₃VO₄ nanoparticles @PAN composite nanofibers was experimentally verified by the destruction of Escherichia coli. These results suggest that the developed inexpensive and functional nanomaterials can serve as a non-precious catalyst for environmental applications.

• Journal of the Korean Ceramic Society
• /
• v.52 no.3
• /
• pp.221-223
• /
• 2015

In this work, we report on the preparation of the anodically-grown $TiO_2$ nanotube arrays sensitized with $In_2S_3$ nanoparticles by using the SILAR (successive ionic layer adsorption and reaction) process. We evaluate the photo-catalytic properties of the prepared hetero-structures under visible-light illumination. The results reveal that the $TiO_2/In_2S_3$ system has enhanced photo-catalytic characteristics including higher chopping height. Improved performance of the heterojunction is attributed to the narrower band gap of $In_2S_3$ and its favorable position within the conduction band relative to that of $TiO_2$.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.1-8
• /
• 2005

In this study, $TiO_2$ powders were prepared by hydro-thermal synthesis with titanium tetra isopropoxide. The prepared $TiO_2$ and the commercial $TiO_2$(P-25, Degussa) were by impregnating $H_2PtCl_6$ solution or the leached solution from the waste catalytic converter of automobile. Modified photocatalysts were analyzed by ICP-AES, UV-DRS, XRD, SEM. And band-gap energy of modified photo-catalyst was found to decreased to 1.76eV and basic structure was changed upon modification by leached solution. Modified photocatalysts were coated on the wallpaper after using mixed solution with adhesive materials(PVC). And then to know the modified photo catalysts tested the reactivity and quantum efficiency in the mixed gas with NO as reactants in the photo catalytic reactor. In the gas phase, photo-catalytic activity of NO was the highest for modified P-25 catalysts(P-25(w)) that P-25(w) was impregnated by leached solution of wasted catalytic converter.

• Restorative Dentistry and Endodontics
• /
• v.17 no.2
• /
• pp.331-341
• /
• 1992

The purpose of this study was to measure the polymerization contraction stress of two types of composite resins; chemical cured type(Cliarfil F II, Kuraray, Japan) and photo-cured type(Photo-Clearfil Bright, Kuraray, Japan). The stresses of composite resin by contraction measured with specially designed measuring device(Fig. 1). The stresses caused by shrinkage during hardening of specimens were measured according to the type of composite resins, thickness of specimen(0.65, 1.30 and 1.95mm), and ratio of catalyst to base in case of only chemical cured composite resin(0.5, 1.0 and 1.5). As the composite resin specimen shrank on hardening, the load cell recorded force vs time automatically on pen-recorder(Toa, Japan) with a cross-head speed 60mm/hr at 0~10 voltages up to 2 hours. The experiments were conducted in a room maintained at $23{\pm}2^{\circ}C$ and relative humidity $50{\pm}10%$. The results were as follows. 1. The contraction stress during hardening was higher in photo cured composite resin than in chemical cured composite resin. 2. The contraction stress during hardening was increased with thickness of composite resin specimen. 3. In chemical cured composite resin, the polymerization contraction stress was decreased with ratio of catalyst and base. 4. The contraction stress during polymerization was higher in early time after insertion of photo cured composite resin and chemical cured composite resin.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.267.2-267.2
• /
• 2016

Semiconductor photo-catalysis offers the potential for complete removal of toxic chemicals through its effective and broad potential applications. Various new compounds and materials for chemical catalysts were synthesized in the past few decades. As one of the most important II-VI group semiconductors, zinc sulfide (ZnS) with a wide direct band gap of 3.8 eV has been extensively investigated and used as a catalyst in photochemistry, environmental protection and in optoelectronic devices. In this work, the ZnS films and nanostructures have been successfully prepared by wet chemical method. We show that the agglomerates with four successive scales are always observed in the case of the homogeneous precipitation of zinc sulfide. Hydrodynamics plays a crucial role to determine the size of the largest agglomerates; however, other factors should be invoked to interpret the complete structure. In addition, studies of the photocatalytic properties by exposure to UV light irradiation demonstrated that ZnS nanocrystals (NCs) are good photo-catalysts as a result of the rapid generation of electron-hole pairs by photo-excitation and the highly negative reduction potentials of excited electrons. A combination of their unique features of high surface-to volume ratios, carrier dynamics and rich photo-catalytic suggests that these ZnS NCs will find many interesting applications in semiconductor photo-catalysis, solar cells, environmental remediation, and nano-devices.

• Journal of the Mineralogical Society of Korea
• /
• v.28 no.1
• /
• pp.29-38
• /
• 2015

Cyanide can be leached out from the cyanidation method which has been used to extract high-purity gold and silver from ores, and it becomes a variety of cyanide complexes associated with heavy metals contained in ores. Such cyanide complexes are considered as persistent and non-degradable pollutants which cause adverse effects on humans and surrounding environments. Based on binding force between heavy metals and cyanide, cyanide complexes can be categorized weak acid dissociable (WAD) and strong acid dissociable (SAD). This study comparatively evaluated the performance of photo-catalytic process with regard to forms of cyanide complexes. In particular, both effects of UV LED wavelength and surface modification of photo-catalyst on the removal efficiency of cyanide complexes were investigated in detail. The results indicate that the performance of photo-catalytic oxidation is significantly affected by the form of cyanide complexes. In addition, the effect of UV LED wavelength on the removal efficiency was quite different between free cyanide and cyanide complexes associated with heavy metals. The results support that the surface modification of photo-catalyst, such as doping can improve overall performance of photo-catalytic oxidation of cyanide complexes.

• Advances in environmental research
• /
• v.5 no.1
• /
• pp.61-77
• /
• 2016

$NanoTiO_2$ was synthesized by ultrasonication assisted sol-gel process and subjected to iron doping and carbon-iron codoping. The synthesized catalysts were characterized by XRD, HR-SEM, EDX, UV-Vis absorption spectroscopy and BET specific surface area analysis. The average crystallite size of pure $TiO_2$ was in the range of 30 - 33 nm, and that of Fe-$TiO_2$ and C-Fe $TiO_2$ was in the range of 7 - 13 nm respectively. The specific surface area of the iron doped and carbon-iron codoped nanoparticles was around $105m^2/g$ and $91m^2/g$ respectively. The coupled semiconductor photo-Fenton's activity of the synthesized catalysts was evaluated by the degradation of a cationic dye (C.I. Basic blue 9) and an anionic dye (C.I. Acid orange 52) with concurrent investigation on the operating variables such as pH, catalyst dosage, oxidant concentration and initial pollutant concentration. The most efficient C-Fe codoped catalyst was found to effectively destruct synthetic dyes and potentially treat real textile effluent achieving 93.4% of COD removal under minimal solar intensity (35-40 kiloLUX). This reveals the practical applicability of the process for the treatment of real wastewater in both high and low insolation regimes.