• 전기학회논문지
• /
• 제62권5호
• /
• pp.604-611
• /
• 2013

This paper presents an second harmonic elimination method based on the impedance variation scheme. Through the power quality analysis from the nonlinear loads connected on the power system, the second harmonic problems have been analyzed with a case study analysis and the experiments. In the paper, the second Harmonic generation was simulated with a single phase SCR rectifier and the analytical model is proposed for the second harmonic generation. A novel impedance variation scheme is proposed and analyzed to eliminate the second harmonic. The experiment has been performed on the 60(MVA) industry manufacturing plant. The experimental result demonstrates the proposed impedance variation scheme successfully operate on the 60(MVA) industry manufacturing plant.

• 대한산업공학회지
• /
• 제36권3호
• /
• pp.154-163
• /
• 2010

Process monitoring of output variables affecting final performance have been mainly executed in semiconductor manufacturing process. However, even earlier detection of causes of output variation cannot completely prevent yield loss because a number of wafers after detecting them must be re-processed or cast away. Semiconductor manufacturers have put more attention toward monitoring process inputs to prevent yield loss by early detecting change-point of the process. In the paper, we propose the method to efficiently monitor functional input variables in multi-phase semiconductor manufacturing process. Measured input variables in the multi-phase process tend to be of functional structured form. After data pre-processing for these functional input data, change-point analysis is practiced to the pre-processed data set. If process variation occurs, key variables affecting process variation are selected using contribution plot for monitoring efficiency. To evaluate the propriety of proposed monitoring method, we used real data set in semiconductor manufacturing process. The experiment shows that the proposed method has better performance than previous output monitoring method in terms of fault detection and process monitoring.

• 한국운동역학회지
• /
• 제27권3호
• /
• pp.181-187
• /
• 2017

Objective: The aim of the study was to compare & analyze on the variations of ground reaction force during ascending and descending of bus stair. Method: Simulated wooden stair of bus (raiser: 37.66 cm, width: 109 cm, tread: 29 cm) and GRF system (AMTI-OR-7/ AMTI., USA) was set up within experimental room. Adult female (n=8) performed ascending & descending of simulated bus stair, and variables analyzed consisted of TT (transfer-time), PVF (peak vertical force), LR (loading rate), DR (decay rate), CV (coefficient of variation) and AI (asymmetry index). Sample data from GRF cut off at 1,000 Hz. Results: TT showed shortest variation at phase 1 during descending, but longest variation at phase 1 during ascending of stair. PVF19 (Fz2, 100%) showed large pattern during descending than that of ascending, but rather showed small pattern during ascending of stair in case of PVF2 (Fz4). LR showed larger pattern during descending than that of ascending, but rather during ascending of stair in case of DR. Variation of CV (%) did not show difference between LR and DR, but showed higher possible occurrence of variation during descending of stair. Also AI (%) showed higher index during ascending than that of descending of stair. Conclusion: Because introduction of lowered bus stair has various realistic problems, if lined up at designated bus stopage exactly, rather can solve problems of inconvenience, reduce impulsive force and secure a stability of COG during ascending & descending of stair.

• 한국광학회지
• /
• 제13권3호
• /
• pp.182-188
• /
• 2002

위상이동 간섭무늬 투영 방법을 이용한 3차원 형상측정 시스템의 위상계산오차를 분석하였다. 본 연구에서 다룬 오차의 요소에는 물체 표면의 특성에 따라 검출기에 나타나는 양자화 크기의 변이 효과, 물체 표면에 맺히는 간섭무늬 패턴의 초점 어긋남 효과, 간섭무늬의 위상이동 오차에 의한 효과, 위상 이동된 간섭무늬 패턴이 투영된 여러 개의 물체 상을 받아들이는 도중에 시스템 및 주위 환경 변화에 의한 오차, 그리고 투영되는 격자 패턴의 왜곡에 의한 효과들을 계산하고 논의하였다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(2)
• /
• pp.537-542
• /
• 1996

In the present work the influence of various physical parameters on the two-phase flow behavior in a self-heated porous medium has been studied using a numerical model, that is, the effects of heat generation rate, of porosity, of particle size, and of system pressure on the dryout process. To analyze the effect of these parameters, the variation of both liquid volumetric fraction and liquid axial velocity is evaluated at the steady state or at the onset of a first boiled-out region. The analysis of computational results indicate that a qualitative tendency exists between the parameters such as heat generation rate, porosity, effective particle diameter and the temporal development of the liquid volumetric fraction field up to dryout. In addition to these parameters, a variation of fluid properties such as phase density, phase viscosity due to a change of system pressure can be used for gaining insight into the nature of two-phase flow behavior up to dryout.

• 전기학회논문지
• /
• 제58권7호
• /
• pp.1405-1410
• /
• 2009

Output voltage of a DC/DC power converter system is likely to be distorted if variable loads exist in the output terminal. This paper presents a new disturbance observer(DOB) approach to maintain a robust regulation of the output voltage of a boost type DC/DC converter. Unlike the buck-type converter case, the regulation problem of the boost converter is very complicated by the fact that, with respect to the output voltage to be regulated, the system is non-minimum phase. Owing to the non-minimum phase property the classical DOB approach has not been applied to the boost converter. Motivated by a recent result on the application of DOB to non-mimimum phase system, an output feedback control law is proposed by using a parallel feedforward compensator. Simulation results using the Simulink SimPowerSystems prove the performance of the proposed controller against load variation.

• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.60-73
• /
• 2008

In this paper a three-phase ac-to-dc resonant converter with high input power factor and isolated output is proposed. To improve the input power factor of the converter, high frequency current is injected into the input of the three-phase diode bridge rectifier. It is injected through an impedance network consisting of a series of L-C branches from the output of the high frequency three-phase inverter. A narrow switching frequency variation is required to regulate the output voltage. A design example with different design curves is illustrated along with the component ratings. Experimental verification of the converter is performed on a prototype of 3 kW, 1000 V output, operating above 300 kHz. Experimental results confirm the concept of the proposed converter. Narrow switching frequency variation is required to regulate the output voltage.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2002년도 종합학술발표회 논문집 Vol.12 No.1
• /
• pp.161-164
• /
• 2002

In this paper, a design technique is introduced for designing a 360-degree linear analog phase shifter at 1.8㎓. Using tunable short-circuit terminated comb-line filters as reactive loads, the circuit gives a very small insertion loss(less than 0.1㏈) and an almost linear phase shifter over the filter bandwidth for the full 360-degree range. We were showed large phase variation with small capacitance variation in the quadrature hybrid coupler using tunable shorted terminated combline filters.

• 비파괴검사학회지
• /
• 제4권2호
• /
• pp.7-14
• /
• 1985

An experiment to investigate the rate of change of phase angle of eddy current output signal caused by outer surface defect of nonferromagnetic tube by variation of standard depth of penetration and variation of percent of tube wall penetration was carried out. The results of the experiment show that the phase angle of defect signal is increased with decreasing the standard depth of penetration or the depth of defect. The results also show that the phase angle is decreased with increasing the skin effect of eddy current, and that the resolution is decreased with decreasing the depth of defect.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1997년도 추계 학술대회논문집
• /
• pp.120-125
• /
• 1997

In the present work the influence of various physical parameters on the two-phase flow behavior in a self-heated porous medium has been studied using a numerical model, that is, the effects of heat generation rate, of porosity, of particle size, and of system pressure on the dryout process. To analyze the effect of these parameters, the variation of both liquid volumetric fraction (i.e., liquid saturation) and liquid axial velocity is evaluated at the steady state or at the onset of a first boiled-out region. The analysis of computational results indicate that a qualitative tendency exists between the parameters such as heat generation rate, porosity, effective particle diameter and the temporal development of the liquid volumetric fraction field up to dryout. In addition to these parameters, a variation of fluid properties such as phase density, phase viscosity due to a change of system pressure can be used for gaining insight into the nature of two-phase flow behavior up to dryout.