• Transactions of Materials Processing
• /
• v.19 no.1
• /
• pp.5-10
• /
• 2010

The current understanding for phase/grain boundary sliding and low-temperature/high-strain rate superplasticity of two-phase titanium alloys is summarized. The quantitative analysis on boundary sliding revealed increased sliding resistance on the order of ${\alpha}/{\beta}\;\ll\;{\alpha}/{\alpha}\;{\approx}\;{\beta}/{\beta}$ boundary, hence, led to the conclusion that approximately 50% alpha(or beta) volume fraction and/or grain refinement is beneficial for obtaining large superplastic elongation at low temperature and/or high strain rate. To predict the temperature for 50% alpha volume in various alpha/beta Ti, artificial neural network was applied. Finally, much enhanced superplasticity was achieved through grain refinement utilizing dynamic globularization.

• Journal of the Korean Ceramic Society
• /
• v.25 no.5
• /
• pp.488-494
• /
• 1988

Effects of MnO2 addition on themicrostructure, dielectric and piezoelectric properties of Rhombohedral, Tetragonal and Morphotropic phase boundary(MPB) in Pb(Ni1/3Nb2/3)O3-PbTiO3-PbZrO3 system were investigated and respectively the amount of MnO2 addition was 0, 0.2, 0.5, 1.0, 3.0wt%. In the tetragonal region, compared with the Rhombohedral and Morpotropic phase boundary, Mechanical quality factor(Qm), Curie temperature(Tc) and Dissipation factor were promoted by addition of MnO2. According to the results of the microstructure, dielectric and piezoelectric properties, the solid solution range of MnO2 addition in this system was 0.2-0.5wt%.

• Journal of the Korean Ceramic Society
• /
• v.35 no.9
• /
• pp.917-922
• /
• 1998

The polarization characteristics of the cathodes were discussed which were composed YSZ and ${(La_{0.75 }Sr_{0.25 })}_{0.95}Mn_{0.8 }Co_{0.2}O_3$ The three-phase-boundary length increased with the addition of YSN resulting in the minimum po-larization resistance at 60(LSMC) : 40(YSZ) wt% When LSMC-YSZ compoiste cathodes was sintered at $1200^{\circ}C$ minimum polarization resistance was observed and the capacitace increased with increasing sintering tem-perature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.1
• /
• pp.24-35
• /
• 1997

Melting process inside in a vertical cylinder has been investigated numerically to observe heat transfer characteristics in the latent heat storage vessel applied to the thermal storage system. The time-dependent boundary fitted coordinate system was introduced to overcome the difficulty caused by the moving boundary. The present results are in good agreement with the available previous data when the initial subcooling effect of the solid phase is not considered. It is found that the melting is promoted by the natural convection, but is delayed by the initial subcooling effect of the solid phase.

• Transactions of Materials Processing
• /
• v.14 no.1 s.73
• /
• pp.65-70
• /
• 2005

A phase mixture model was employed to simulate the deformation behaviour of metallic materials covering a wide grain size range from micrometer to nanometer scale. In this model a polycrystalline material is treated as a mixture of two phases: grain interior phase whose plastic deformation is governed by dislocation and diffusion mechanisms and grain boundary 'phase' whose plastic flow is controlled by a boundary diffusion mechanism. The main target of this study was the effect of grain size on stress and its strain rate sensitivity as well as on the strain hardening. Conventional Hall-Petch behaviour in coarse grained materials at high strain rates governed by the dislocation glide mechanism was shown to be replaced with inverse Hall-Petch behaviour in ultrafine grained materials at low strain rates, when both phases deform predominantly by diffusion controlled mechanisms. The model predictions are illustrated by examples from literature.

• Transactions of Materials Processing
• /
• v.25 no.4
• /
• pp.248-253
• /
• 2016

Induction hardening process of tubular drive shaft for automobile is simulated by combining the thermal, mechanical, electro-magnetic and metallurgical analysis models. Various material properties for each analysis model are obtained in a consistent way via material properties calculation software, JMatPro^®. To consider the scanning process of induction heating, boundary element method is adopted for electro-magnetic field calculation. The distribution of temperature, stress and phase volume fraction are tracked out through the whole process and the effect of scanning velocity is reviewed. The analysis result shows that the critical principal stress is developed at the phase boundary where martensite is formed.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2008.05a
• /
• pp.43.1-43.1
• /
• 2008

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.06a
• /
• pp.76-83
• /
• 2000

Boundary lubrication condition arises in most lubricated systems, especially during motion reversals and start up phase of operation. In this work electric contact resistance variations with respect to sliding conditions under lubrication is investigated The motivation was to improve the understanding of the contact condition in the boundary lubrication regime. It is shown that electrical contact resistance is sensitive to sliding speed and surface condition of the specimens. Also, phenomena such as run-in during the initial phase of sliding and lubricant pile up near the sliding pin could be observed. The results of this work will aid in better understanding of the metal to metal contact condition in lubricated systems.

• Nuclear Engineering and Technology
• /
• v.38 no.8
• /
• pp.763-778
• /
• 2006

Injection of microbubbles within the turbulent boundary layer has been investigated for several years as a method to achieve drag reduction. However, the physical mechanism of this phenomenon is not yet fully understood. Experiments in a channel flow for single phase (water) and two phase (water and microbubbles) flows with various void fraction values are studied for a Reynolds number of 5128 based on the half height of the channel and bulk velocity. The state-of-the art Particle Tracking Velocimetry (PTV) measurement technique is used to measure the instantaneous full-field velocity components. Comparisons between turbulent statistical quantities with various values of local void fraction are presented to elucidate the influence of the microbubbles presence within the boundary layer. A decrease in the Reynolds stress distribution and turbulence production is obtained with the increase of microbubble concentration. The results obtained indicate a decorrelation of the streamwise and normal fluctuating velocities when microbubbles are injected within the boundary layer.

• Tribology and Lubricants
• /
• v.16 no.5
• /
• pp.381-388
• /
• 2000

Boundary lubrication condition arises in most lubricated systems, especially during motion reversals and start up phase of operation. In this work electric contact resistance variations with respect to sliding conditions under lubrication is investigated. The motivation was to improve the understanding of the contact condition in the boundary lubrication regime. It is shown that electrical contact resistance is sensitive to sliding speed and surface condition of the specimens. Also, phenomena such as run-in during the initial phase of sliding and lubricant pile up near the sliding pin could be observed. The results of this work will aid in better understanding of the metal to metal contact condition in lubricated systems.