• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.393-395
• /
• 2005

The bonding for Aluminum and Copper in the air is investigated in this study. This bonding method does not include the special process of removing aluminum oxide films. In case of this bending, each metal Is heated at bonding temperature where is above eutectic temperature of Al-Cu system and below melting point of Aluminum. The liquefaction around the bonding surface occurs after the diffusion at solid state of each metal. This phenomenon is predicted by the temperature range above eutectic temperature of Al-Cu equilibrium phase diagram.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.3
• /
• pp.281-288
• /
• 1999

Electrodeposited Zn-Ni alloy coatings are of particular interest for improving the corrosion resistance of steel in a number of enviornments. Of particular interest is the relationship between composition, structure and corrosion rate. This paper firstly reviews the literature regarding composition-structure relationships of Zn-Ni electrodeposits and compares them with the equilibrium phase diagram. Secondly, research was carried out on a wide range of coatings which were produced in the laboratory and their structure and corrosion rates determined. It was found that unambiguous identification of phases from XRD data can be difficult. Maximum corrosion resistance of deposits is obtained at 12-13% Ni, with a $\gamma$ phase structure and predomination of (600) and (411) reflections. Compatibility is important with regard to chromate conversion coatings.

• Resources Recycling
• /
• v.23 no.5
• /
• pp.21-27
• /
• 2014

A study on the solvent extraction for the recovery of Li from lithium-containing waste solution was investigated using $D_2EHPA$ as an extractant. The experimental parameters, such as the pH of the aqueous solution, concentration of extractant and phase ratio were observed. Experimental results showed that the extraction percentage of Li was increased with increasing the equilibrium pH. More than 50% of Li was extracted in eq. pH 6.0 by 20% $D_2EHPA$. From the analysis of McCabe-Thiele diagram, 95% of Li was extracted by four extraction stage at phase ratio(O/A) of 3.0. Stripping of Li from the loaded organic phases can be accomplished by sulfuric acid as a stripping reagent and 90 ~ 120 g/L of $H_2SO_4$ was effective for the stripping of Li. Finially, Li was concentrated about 11.85 g/L by continuous stripping process, and then lithium carbonate was prepared by precipitation method.

• Journal of Powder Materials
• /
• v.23 no.3
• /
• pp.202-206
• /
• 2016

A Ni-Ti-B alloy powder prepared by mechanical alloying (MA) of individual Ni, Ti, and B components is examined with the aim of elucidating the phase transitions and crystallization during heat treatment. Ti and B atoms penetrating into the Ni lattice result in a Ni (Ti, B) solid solution and an amorphous phase. Differential thermal analysis (DTA) reveals peaks related to the decomposition of the metastable Ni (Ti, B) solid solution and the separation of equilibrium $Ni_3Ti$, $TiB_2$, and ${\tau}-Ni_20Ti_3B_6$ phases. The exothermal effects in the DTA curves move to lower temperatures with increasing milling time. The formation of a $TiB_2$ phase by annealing indicates that the mechanochemical reaction of the Ni-Ti-B alloy does not comply with the alloy composition in the ternary phase diagram, and Ti-B bonds are found to be more preferable than Ni-B bonds.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.4
• /
• pp.1437-1448
• /
• 1996

This paper presents a simplified model for approximate analysis of the solute redistribution in coarsening dendrite arms during solidification of binary metal alloys. By introducing a quadratic concentration profile with a time-dependent coefficient, the integral equation for diffusion in the solid phase is reduced to a simple differential relation between the coefficient and the solid-liquid interface position. The solid fraction corresponding to the system temperature is readily determined from the relation, phase equilibrium and the overall solute balance in which the liquid phase is assumed to be completely mixed. In order to validate the developed model, calculations are performed for the directional solidification of Al-4.9 mass Cu alloy. The predicted eutectic fractions for a wide range of the cooling rate reasonably agree with data from the well-known experiment as well as sophisticated numerical analyses. Also, the results for the back diffusion limits are consistent with available references. Additional calculations show that the characteristic parameters such as the coarsening, density variation and nonlinarity in the phase diagram significantly affect the microsegregation. Owing to the simplicity, efficiency and compatibility, the present model may be suitable for the micro-macroscopic solidification model as a microscopic component.

• Journal of Powder Materials
• /
• v.21 no.5
• /
• pp.338-342
• /
• 2014

In the present work, we investigated the mechanical alloying of binary Ga-Se(1:1) and Ga-Te(1;1) sysyems. The high-energy ball-milling was performed at $40^{\circ}C$ where one of constituents (Ga) is molten state. The purpose of the work was to see whether reactions between constituent elements are accelerated by the presence of a liquid phase. During the ball-milling, the liquid Ga phase completely disappeared and the resulting powders consist of nanocrystalline grain of ~20 nm with partly amorphized phases. However, no intermetallic compounds formed in spite of the presence of the liquid phases which has much higher diffusivity than solid constituents. By subsequent heat-treatments, the intermetallic compounds such as GaSe and GaTe formed at relatively low temperatures. The formation temperature of theses compound was much lower than those predicted by equilibrium phase diagram. The comparison of the ball-milled powders with un-milled ones indicated that the easy formation of intermetallic compound or allying occurs at low temperatures.

• Journal of the Korean Institute of Gas
• /
• v.7 no.3 s.20
• /
• pp.32-43
• /
• 2003

As this paper is observed the phase equilibrium diagram of mono- (methane) and multi-component(natural gas) hydrates, and the hydrate growth behavior is analysed and compared by the experiments during the reaction. The difference of mono and multi-component hydrates is an induction delay time and a plateau region. And the concentration of component of gases is changed during the reaction in multi-component hydrates and the concentration of components is changed during the decomposition of hydrate according to each decomposing rates of gases. At 6 MPa, 276.65 K and 600 rpm, the induction delay time of multi-component hydrate formation is observed shorter than that of mono-component hydrate formation because the hydrate nuclei of gases except methane form faster than those of methane. And the plateau region of mono-component hydrate is observed distinctly at 0.055 mole of $CH_4$/mole of water and that of multi-component hydrate is observed at 0.04 mole of $CH_4$/mole of water.

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.4
• /
• pp.358-365
• /
• 2003

Zirconium nitride powders were synthesized at a relatively lower temperature using methane as a reducing agent in the nitridation of zircoia. $ZrO_2$ powder was prepared by a sol-gel technique. The resulting sol-gel was centrifuged, and the gel was washed with deionized water. Anhydrous ammonia was used as the nitrogen source and methane was used as the reducing agent. Conversion diagrams show the equilibrium solid phase as a function of reagent concentrations for a specific temperature and gas pressure for the reagent system $NH_3-ZrO_2-CH_4$. The reagent concentration ranges within which pure ZrN is formed increase with increasing reaction temperature. Low pressure with an excess of hydrogen decreases the reaction temperature at which pure ZrN is formed. Low pressure together with the introduction of excess hydrogen into the reaction system increases Zr and N conversion efficiency and retards C deposition.

• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.111-120
• /
• 1998

To predict and evaluate metallurgical and mechanical behavior of th welds, it is essential to understand solidification behavior and microstructural evolution experienced in the welds, neither of which follows the equilibrium phase diagram because of rapid heating and cooling conditions. Metallurgical phenomena in austenitic stainless steel fusion welds, types 304, 309S, 316L, 321 and 304N, were investigated in this study. Autogenous GTA welding was performed on weld coupons, and primary solidification mode and phase distribution were investigated from the welds. Varestraint test was employed to evaluate solidification cracking susceptibilities of the alloys. GTA weld fusion zones in type 304, 321 and 304N stainless steels experienced primary ferrite solidification while those in type 309S primary austenite solidification. Type 316L exhibited a mixed type of primary ferrite and primary austenite solidification. The primary solidification mode strongly depended on $Cr_{eq}/Ni_{eq}$ ratio. In terms of solidification cracking susceptibility, type 309S that solidified as primary austenite exhibited high cracking susceptibility while the alloys experienced primary ferrite solidification showed low cracking susceptibility. The relative ranking in solidification cracking susceptibility was type 304=type 304N < type 321 < type 316L < type 309S.

• Journal of Environmental Science International
• /
• v.9 no.3
• /
• pp.241-252
• /
• 2000

Twenty-two water samples(fifteen groundwater and seven geothermal water samples) were collected to elucidate chemical characteristics of the ground and geothermal waters in the Haeundae hot spring area and its vicinity. Major and honor elements were analyzed for ground and geothermal water samples. The concentrations of $K^+$, Na+$, $Ca^{2+}$, $SO_4^{2-}$, $Cl^-$, ^F^-$ and $SiO_2$ were higher in the geothermal water samples than the groundwater samples except $HCO_3^- and Mg^{2+}$ ions. Based on the contents of Fe, Zn, Cu, Al, Mn and Pb, some of the ground and geothermal water samples are contaminated by anthropogenic sources. The ground waters shown on the Piper diagram belong to $Ca-HCO_3$ type, while the geothermal waters Na-Cl type. The graphs of $Cl^-$ versus $Na^+$, $Ca^{2+}, Mg^{2+}, K^+, SO_4^{2-} and HCO_3^-$ indicate that the groundwater is related partly with mineral-water reaction and partly with anthropogenic contamination, while the geothermal water is related with saline water. On the phase stability diagram, groundwater and thermal water mostly fall in the field of stability of kaolinite. This indicates that the ground and geothermal waters proceed with forming kaolinite. Factor and correlation analyses were carried out to simplify the physicochemical data into grouping some factors and to find interaction between them. Based on the Na-K, Na-K-Ca and Na-K-Ca-Mg geothermometers and silica geothermometers, the geothermal reservoir is estimated to have equilibrium temperature between 125${$\mid$circ}C$ and 160${$\mid$circ}C$.