• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.9 s.112
• /
• pp.811-820
• /
• 2006

Ultra wideband CPW batons are proposed in this paper. The proposed talons are consisted of ultra wideband multi-stage Wilkinson dividers and 'X'-shaped $180^{\circ}$ out-of-phase generator. Bottom-bridges and via-holes are used to connect CPW ground lines instead of the conventional air-bridges which require troublesome manual working in fabrication with HMIC(Hybrid Microwave Integrated Circuits) substrates. The proposed CPW batons have ultra wideband of 3 or $10(=F_{figh}/F_{low})$ theoretically, the wideband characteristics and S-parameters of the basis Wilkinson divider are directly converted to those of the proposed batons. The proposed batons are so compact and small compared to the conventional Wilkinson batons because no additional area for out-of-phase section is required. So the size of the proposed batons is exactly the same as that of the basis Wilkinson dividers. As examples, 3-stage and 7-stage wideband Wilkinson dividers are converted to the proposed batons. Their measured operating bandwidth are $1\sim3GHz$ and $0.8\sim5GHz$, respectively, with excellent matching, isolation and power division performances. The measured magnitude and phase balance errors are ${\pm}0.5dB\;and\;0.45\;dB,\;and\;{\pm}5^{\circ}\;and\;{\pm}10^{\circ}C$ over $1\sim3GHz\;and\;0.8\sim5GHz$, respectively.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.40 no.2
• /
• pp.133-139
• /
• 2014

Oil-in-water nanoemulsions were prepared in the system of water/Span 80-Tween 80/long-chain paraffin oil via the PIC (phase inversion composition) method. With the increase of preparation temperature from $30^{\circ}C$ to $80^{\circ}C$, the diameter of emulsion droplets decreased from 120 nm to 40 nm, proving the formation of nanoemulsions. By varying the HLB (hydrophilic lipophilic balance) of mixed surfactants, we found that there was an optimum HLB around 12.0 ~ 13.0 corresponding to the minimum droplet size. The viscosity of nanoemulsions clearly increased with droplet volume fraction, f, but the droplet size slightly increased. Significantly, at ${\phi}{\leq}0.3$, the size distribution of nanoemulsions kept constant more than 2 months. These results proved that the viscous paraffin oil can hardly be dispersed by the PIC method at $30^{\circ}C$, but the increase in preparation temperature makes it possible for producing monodisperse nanoemulsions. Once the nanoemulsion is produced, the stability against Ostwald ripening is outstanding due to the extremely low solubility of the liquid paraffin oil in the continuous phase. The highly stable nanoemulsions are of great importance in cosmetic applications.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.263-263
• /
• 2006

Poly (ethylene glycol)(PEG) - Poly (${\varepsilon}-caprolactone(CL)$) - Poly (D,L lactide(LA) (PCLA-PEG-PCLA) was synthesized by ring-opening polymerization to form temperature sensitive hydrogel triblock copolymer. The triblock copolymer was acrylated by acryloyl chloride. ${\beta}-amino$ ester was used as a pH sensitive moiety, in this study ${\beta}$- amino ester obtained from 1,4-butandiol diacrylate, and 4, 4' trimethylene dipiperidine, it have pKb around 6.6. pH/temperature sensitive penta-block copolymer (PAE-PCL-PEG-PCL-PAE) was synthesized by addition polymerization from acrylated triblock copolymer, 1,4-butandiol diacrylate, and 4, 4' trimethylene dipiperidine. Their physicochemical properties of triblock and penta-block copolymers were characterized by $^1H-NMR$ spectroscopy and gel permeation spectroscopy. Sol-gel phase transition behavior of PAE-PCL-PEG-PCL-PAE block copolymers were investigated by remains stable method. Aqueous media of the penta-block copolymer (at 20 wt%) changed from a sol phase at pH 6.4 and $10^{\circ}C$ to a gel phase at pH 7.4 and $37^{\circ}C$. The sol-gel transition properties of these block copolymers are influenced by the hydrophobic/hydrophilic balance of the copolymers, block length, hydrophobicity, stereo-regularity of the hydrophobic of the block copolymer, and the ionization of the pH function groups in the copolymer depended on the changing of environmental pH, respectively. The degradation and the stabilization at pH 7.4 and $37^{\circ}C$, and the stabilization at pH 6.4 and $10^{\circ}C,\;5^{\circ}C,\;0^{\circ}C$, of the gel were determined. The results of toxicity experiment show that the penta block copolymer can be used for injection drug delivery system. The sol?gel transition of this block copolymer also study by in vitro test ($200{\mu}l$ aqueous solution at 20wt% polymer was injected to mouse). Insulin loading and releasing by in vitro test was investigated, the results showed that insulin can loading easily into polymer matrix and release time is around 14-16days. The PAE-PCL-PEG-PCL-PAE can be used as biomaterial for drug, protein, gene loading and delivery.

• Korean Journal of Psychosomatic Medicine
• /
• v.5 no.1
• /
• pp.3-11
• /
• 1997

In becoming parents, the marital partners enter into a new developmental phase. The conception of the child is an act of mutual creativity during which the boundaries between the self and another were temporarily obliterated more completely than at any time since infancy. The infant is a physical fusion of the parents, and their personalities unite within the child. for many women, creativity as a mother becomes a central matter that provides meaning and balance to their lives. The husband usually has strong desires for an offspring and can be transformed by it. The child can profoundly affect one or both parents, and the influences are reciprocal-a child's needs or specific difficulties uncover a parent's inadequacy. following the child's development, each transition into a new developmental phase requires an adaptation by the parents, and one or another of these required adaptations may disturb a parent's equilibirium. And the personality changes, emotional difficulties, and regressions of a spouse that occur in response to some phase of parenthood can upset the marriage. Not only do children identify with parents, but parents also identify with their children. The parents take pleasure in child's joy and suffer with the child's pain more than in almost any other relationship. certain respects e parents lives again in the child. Through the process of identification the child can also provide one of the two parents with the opportunity to experience intimately the way in which a person of the opposite gender grows up. Parenthood also provides the opportunity to be loved, admired, and needed simply because one is a parent and, as such, a central and necessary object in the young child's life. The many potentialities for emotional satisfactions from parenthood manage to outweigh the tribulations and sacrifices that are required. The child also exerts an indirect effect through changing the parent's position in the society, for new sets of relationships are established as the parents are drawn to other couples with children of the same age, and for a new impetus toward economic and social mobility often possesses the parents. frequently the couple's relatedness to their own parents improves and grows firmer once again. Parenthood, the satisfactions it provides and the demands it makes, varies as life progresses : and changes with the parent's interests, needs, and age as well as with the children's maturation. There are phases in the child's life that the parents are reluctant to have pass, whereas they tolerate others largely through knowing that they will soon be over. The changing lives of the children provide many satisfactions that offset the tribulations, uncertainties, and regrets. The parents change. The young father, who was just starting on his carrier whom the first child was born, settles into a life pattern. He becomes secure with increasing achievement and interacts differently with the youngest child and provides a different model for him than for the oldest. The mother may have less time for a second or third child than for her first, but she may also be more assured in her handling of them. The birth of a baby when the parents art in their late thirties will find them Less capable of physical exertion with the child and less tolerant of annoyances, but they are less apt to be annoyed. Eventually the children min and leave home, but the couple do not cease to be parents.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.7
• /
• pp.761-768
• /
• 2010

This paper presents an effective method to achieve the wideband waveform for high resolution SAR(Synthetic Aperture Radar) using the frequency multiplication technique. And also this paper analyzes the root causes for the spectral regrowth due to 3rd-order intermodulation in chirp bandwidth expansion scheme using quadrature modulator and frequency multipliers. The amplitude and phase imbalance requirement are defined based on the simulation results in terms of quadrature channel imbalance. This minimizes the degradation of range resolution, peak sidelobe ratio and integrated sidelobe ratio. The wideband chirp generator using the frequency multiplier and memory map scheme was manufactured and the compensation technique was presented to reduce the spectral regrowth of SAR waveform by minimizing the amplitude and phase imbalance. After I and Q channel imbalance adjustment, the carrier level reduces －28.7 dBm to －53.4 dBm. Chirp signal with 150 MHz bandwidth at S-band expands to 600 MHz bandwidth at X-band. The sidelobe levels are reduced by about 8 to 9 dB by compensating the amplitude balance between I and Q channels.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.4
• /
• pp.906-911
• /
• 2004

In this paper, a VCDRO(Voltage Control Dielectric Resonator Oscillator) applied to FMCW(Frequency Modulated Continuous Wave)Radar as stable source is implemented and constructed with a MESFET(Metal-semiconductor Field-Effect Transistor) for low noise, a dielectric resonate. of high frequency selectivity, and high Q varator diode to obtain a good phase noise performance and stable sweep characteristics. The designed circuits is simulated thrash harmonic balance simulation technique to provide the optimum performance. The measured result of a fabricated VCDRO shows that output is 2.22㏈m at 12.05GHz, harmonic suppression -30㏈c, phase noise -130㏈c at 100KHz offset, and sweep range of varator diode $\pm$18.7MHz, respectively. This oscillator will be available to FMCW Radar.

• Korean Journal of Applied Biomechanics
• /
• v.24 no.2
• /
• pp.139-149
• /
• 2014

The purpose of this study was to evaluate the effect of angle change of forefoot's adhesive outsole on the electromyographic activity (EMG) of the erector spinae and selected lower limbs muscle during downhill walking over $-20^{\circ}$ ramp. Thirteen male university students (age: $25.4{\pm}3.9$ yrs, height: $176.2{\pm}5.1$ cm, weight: $717.4{\pm}105.0$ N) who have no musculoskeletal disorder were recruited as the subjects. To assess the myoelectric activities of selected muscles, six of surface EMG electrodes with on-site pre-amplification circuitry were attached to erector spinae (ES), rectus femoris (RF), biceps femoris (BF), tibialis anterior (TA), lateral gastrocnemius (LG), and medial gastrocnemius (MG). To obtain maximum EMG levels of the selected muscles for normalization, five maximum effort isometric contraction were performed before the experimental trials. Each subject walked over $0^{\circ}$ and $20^{\circ}$ ramp with three different forefeet's EVA outsole (0, 10, $20^{\circ}$) in random order at a speed of $1.2{\pm}0.1$ m/s. For each trial being analyzed, five critical instants and four phases were identified from the recording. The results of this study showed that the average muscle activities of MG and LG decreased in $20^{\circ}$ shoes compared to $0^{\circ}$ and $10^{\circ}$ ones in the initial double limb stance (IDLS). In initial single limb stance (ISLS) phase, the average muscle activities of ES increased with the angle of forefoot's adhesive outsole, indicating that the increment of shoes' angle induce upper body to flex anteriorly in order to maintain balance of trunk. In terminal double limb stance (TDLS) phase, average muscle activities of TA significantly increased in $20^{\circ}$ outsole compared to $0^{\circ}$ and $10^{\circ}$ ones. There was no external forces acting on the right foot other than the gravity during terminal single limb stance (TSLS) phase, all muscles maintained moderate levels of activity.

• Journal of Food Hygiene and Safety
• /
• v.32 no.5
• /
• pp.424-433
• /
• 2017

Antioxidants are used in the manufacturing of commercial food packages made of polyolefin plastic such as polyethylene and polypropylene for the purpose to delay the oxidation reaction of the polymer due to oxygen or traces of ozone in the atmosphere. Additives in plastics may be migrated from the packaging materials into foods, thereby presenting a potential health risk to the consumer. Therefore, it is necessary to determine migration level of antioxidants from food packaging materials to foodstuffs in order to take proactive management. In this study, we have developed a method for the analysis of 10 antioxidants, which are butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), Cyanox 2246, 425 and 1790, Irgafos 168, and Irganox 1010, 1330, 3114 and 1076, migrated from the food packaging materials into four food simulants for aqueous, acidic, alcoholic and fatty foods. The antioxidants were determined by reversed-phase high-performance liquid chromatograph-ultraviolet detector with 276 nm after solid-phase extraction with a hydrophilic-lipophilic balance (HLB) cartridge or dilution with isopropanol. The analytical method showed a good linearity of coefficient ($R^2{\geq}0.99$), limits of detection (0.11~0.41 mg/L), and limits of quantification (0.34~1.24 mg/L). The recoveries of antioxidants spiked to four food simulants ranged from 71.3% to 109.4%. The migrated antioxidants in this study were within the safety levels that resulted from the safety assessment by the estimated daily intake to the tolerable daily intake.

• Journal of Food Hygiene and Safety
• /
• v.32 no.5
• /
• pp.434-442
• /
• 2017

The UV light in sunlight breaks down the chemical bonds in a polyolefin polymer through a process called photodegradation, ultimately causing cracking, chalking, colour changes, and loss of physical properties such as impact strength, tensile strength, elongation, and others. UV absorbers are used to prevent or terminate the oxidation of plastics by UV light. They are receptive to UV radiation and dissipate the energy harmlessly as heat. Benzotriazoles and benzophenones are used mainly in polyolefins such as polyethylene and polypropylene. In this study, we have developed a method for the analysis of 12 UV absorbers, which are Uvinul 3000, Cyasorb UV 24, Uvinul 3040, Tinuvin 312 and P, Seesorb 202, Chimassorb 81, Tinuvin 329, 234, 326, 328 and 327, migrated from the food packaging materials into four food simulants for aqueous, acidic, alcoholic and fatty foods. The UV absorbers in food simulants were determined by reversed-phase high performance liquid chromatograph-ultraviolet detector with 310 nm after solid-phase extraction with a hydrophilic-lipophilic balance (HLB) cartridge or dilution with isopropanol. The analytical method showed a good linearity of coefficient ($R^2{\geq}0.99$), limits of detection (0.049~0.370 mg/L), and limits of quantification (0.149~1.120 mg/L). The recoveries of UV absorbers spiked to four food simulants ranged from 70.05% to 110.13%. The developed method would be used as a reliable tool to determine concentrations of the migrated UV absorbers.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.3
• /
• pp.655-668
• /
• 1994

Conventional deodorization filters using soil and compost reach the capacity limitation of deodorization in short period, because its removal mechanism primarily depends on adsorption. Therefore, in this study the experiment was performed on the removal of ammonia which is a strong inorganic malodor, frequently emitted from night soil treatment plants and sewage treatment plants, by seeding activated sludges on the bio-peat containing higher organic contents, water conservation capacity, permeability and lower pressure drop. As a result, in raw peat filter natural ammonia outlet was observed in consequence of pH increase resulted from ammonia ionizing in liquid phase. Ammonia removal mechanism primarily depended on the adsorption onto the anion colloidal substances in peat. In peat bio-filter, theoretical ammonium salts ratio was higher than that of raw peat, resulted from slight pH increase by microorganism activity, however, the experimetal value of ammonia-nitrogen accumulated in bio-peat was lower than that of raw peat because of nitrification by nitrifying bacteria. In the initial reaction period, adsorption was predominant in the ammonia removal mechanism, but nitrification was conspicuous after the middle period. Mass balance of nitrogen was established using experimental data of input $NH_3$ loading, output $NH_3$ loading, $NH_4{^+}$-N, $NO_x$-N, and Org-N. The critical time of unsteady state, which is the maximum activating point of microorganism in bio-filter, was determined using experimental data, and the ammonia adsorption curve was computed using regression analysis. On the basis of the results obtained by above analysis, the delay days for the saturation of adsoption capacity in peat bio-filter was calculated.