• Journal of Power Electronics
• /
• v.13 no.2
• /
• pp.250-255
• /
• 2013

This paper proposes an optimal current distribution method of dual-rotor brushless DC machines (DR-BLDCMs) which have inner and outer surface-mounted permanent-magnet rotors. The DR-BLDCM has high power density and high torque density compare to the conventional single rotor BLDCM. To drive the DR-BLDCM, dual 3-phase PWM inverters are required to excite the currents of a dual stator of the DR-BLDCM and an optimal current distribution algorithm is also needed to enhance the system efficiency. In this paper, the copper loss and the switching loss of a DR-BLDCM drive system are analyzed according to the motor parameters and the switching frequency. Moreover, the optimal current distribution method is proposed to minimize the total electrical loss. The validity of the proposed method was verified through several experiments.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.490-492
• /
• 1997

This paper describes a digital sensorless drive of permanent magnet brushless DC (PM BLDC) motors. The sensorless drive adopts a digital filter - moving average finite impulse response filter for accurate estimation of commutation time. Experimental results show that the performance of the proposed sensorless drive is superior to that of the sensorless drive without filtering.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.2
• /
• pp.130-136
• /
• 2011

This paper presents the torque control algorithm of a permanent magnet synchronous motor(PMSM) for an electric scooter. The volume of the in-wheel type motor is restricted due to the complicated mechanical structure in wheel of an electric scooter, so the hall sensors instead of resolver and encoder for the rotor position sensors are installed. In this paper, the rotor speed and position are estimated from the speed estimator for vector control of a PMSM with hall sensors. The motor starts to rotate at standstill in BLDC mode with 120 degree conduction. After start up, the operating mode is changed to the vector control with maximum torque per ampere(MTPA) operation at low speeds and flux weakening control at high speeds. The performance of the proposed control algorithm is verified through the experiment in the electric scooter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.540-545
• /
• 2001

In case of small motors, coil bundle occupies a large portion of stator in view of mass and volume as well as dynamics. It is observed through modal test on the stator of an IPM BLDC (interior permanent magnet brushless direct current) motor that coil bundle wound on the stator core causes the first and second natural frequencies to decrease by about 20-30% compared with those of bare stator. Especially the third natural frequency is newly observed below 3 KHz, which is not observed on the bare stator. It is found that at the third mode the end-coil and the core vibrate out of phase in radial direction. In this paper, the stator is dynamically modeled in terms of the core and the coil bundle consisting of the end-coil and the slot coil based on the above observations for the prediction of dynamic properties. The core can easily be modeled using finite element method with its actual material properties and geometric shape. The concept of equivalent bending stiffness is used for modeling of the end-coil so that predictions may match with the measured natural frequencies for the end-coil cut out of the stator. Although the same concept can be applied to the slot coil, separation of the slot coil from the stator is impractical. Therefore, equivalent bending stiffness of the slot coil is determined through iterative comparisons with the measurements of natural frequencies of the stator with the slot coil in it.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.835-836
• /
• 2006

최근의 선박 추진시스템은 기존의 엔진, 터빈 등의 구동 원에서 선박의 발전기로부터 선체 외부의 프로펠러와 일체형으로 구성된 모터를 구동하여 추진하는 전기추진식으로 변화되고 있다. 특히, 히토류계 영구자석재질의 발달로 인하여 대형 선박의 추진을 위한 대용량 자석계자형 BLDC와 영구자석형 동기전동기의 설계가 가능해 졌으며, 이에 대한 연구구도 활발히 이루어지고 있다. 그러나 이도 중 소형 선박기기에 한정되어 있으며, MW급 이상의 대형기기의 설계 연구도 일부 선진국에서만 진행 되고 있는 실정이다. 이에 본 연구에서는 5MW, 150rpm급 대용량 추진전동기 설계에 관한 연구를 하였다. 본 설계 모델은 오랜 기간 해양 운행을 해야 하는 선박특성 상 중요한 부분인 에너지 효율을 높이기 위하여 인버터를 전동기 내부에 배치한 구조로 부피와 중량을 줄이고, 더불어 속도에 따라 인버터를 커플링하여 상변환이 가능한 전동기를 설계하였다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.6
• /
• pp.21-30
• /
• 2022

This paper describes the design, manufacture, and testing of servos applicable to small tracking radars. First, Chapter 1 describes the necessity of this study. Chapter 2 describes the development of servos applicable to future tracking radars in small missile systems. Chapter 3 describes the design and test results for current control of brushed DC motors, brushless DC motors, and permanent magnet synchronous motors. And Chapter 4 describes the design and test results for speed control of the test wheel. And in Chapter 5, the results of the previous tests are summarized. In this paper, some pictures were intentionally blurred for security reasons, and the control result of test wheel was described, not the test with the developed gimbals.