• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.3
• /
• pp.449-459
• /
• 1999

The scattering problems from electromagnetic absorbers can be greatly simplified using the transmission line approximations (TLA) and effective medium theory. This method has been widely used for the absorber design because of its very simple calculation and intuitional approach, while numerical analysis needs the tremendous computation requirements, This paper examined the accuracy and limitations originated by the intrinsic approximation limits of TLA by comparison with FEM results for various absorber design examples. It was found that the TLA result is valid when λ $\geq$ 2p, where λ is the wavelength of the interested upper frequency and p is the distance between two periodic cone arrays. Therefore, the electromagnetic absorbers having high material properties and big base-area commonly do not meet this condition, and the electromagnetic scattering from those absorbers must be evaluated by the numerical analysis in those cases.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.55 no.5
• /
• pp.195-201
• /
• 2006

Tower footing resistance and fault current division factor are important design factors for evaluation of the lightning performance of the transmission line and/or design of the grounding electrode system. The periodic measurement of those factors are also important to verify that the grounding performance of the towers has been maintained good. However, the direct measurement of those factors in operating or energized condition is very difficult because of many practical reasons, such as the difficulty of disconnecting overhead groundwires from the tower under test. With supports by GECOL (General Electricitiy Company of Libya), we had a special chance to conduct Fall-Of-Potential (FOP) test on the energized 220 kV transmission towers before and after disconnecting the overhead groundwires from the towers under test. In this paper, the FOP test results on the towers and the fault current division factors estimated from the comparision of the FOP tests with and without overhead groundwires were presented. The computer models for the FOP test simulations were also constructed to find that the simulated results agreed very well with the measured ones.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.929-931
• /
• 1993

The design sensitivity analysis based on the finite element method is presented for the eddy current problem with a voltage source. Since, in this problem, the complex variable is used as the state variable, new approach to the sensitivity calculation for the complex variable system is required. Its result is applied to the design of the rotor slot shape of squirrel cage induction motor. As a analysis model, only one slot pitch of rotor is analyzed by using a Periodic boundary condition. The use of this minimal modelling method leads to much saving of calculation time. The design objective is to obtain the desired slip-torque characteristic. Because the shape of rotor slot has much influence on the slip torque characteristic, the design variables are taken on the interface shape between rotor core and rotor bar. The initial shape of rotor slot is the trapezoidal type with rounding corners. The obtained final shape is quite similar to the double squirrel cage type.

• Journal of Power System Engineering
• /
• v.21 no.4
• /
• pp.18-25
• /
• 2017

This paper deals with vibration control of a small mount with MR(Magneto-Rheological) fluid as a functional fluid mount for precision equipment of automobiles. Damping and stiffness coefficients of the mount with MR fluid are changed by variations of the applied magnetic field strength. We present the robust control scheme, based on a conventional sliding mode control theory, for the design of a stable controller that is capable of vibration control due to various disturbances such as impact and periodic excitations, and is insensitive to dynamic properties of the mount. We got stable controller by using Lyapunov stability theory. The controller is then realized by using a semi-active control condition in simulations. Chattering problem of the sliding mode control is eliminated by saturation function instead of signum function. The sliding mode control with Lyapunov stability theory is superior to passive and Sky-Hook control in performance.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.1 s.145
• /
• pp.22-31
• /
• 2006

Recent studies have shown that the short time solution of the equation of motion for the rolling of ships is important in deciding the possibility of capsize of ships due to the excessive heel. Since most of known solutions for nonlinear equations of motion are long time or steady periodic solutions, here a simple way is described to get the short time solutions of the Duffing equation, which was chosen for deriving a criterion for the capsize of the ship. With the small external rolling moment, we first assume the state of the small damping and near resonance. Then, for cases when the frequency of the external moment is higher than the resonant one, an inequality was derived as a criterion for the capsize. This gives the range of the initial condition and the magnitude of the external moment which should be avoided for a ship to be safe from capsize. Furthermore, from the linearized equation, it is also shown that a simple and self-explanatory solution can be obtained consistent with that for the case of no damping, which yields the well-known linear growth with time.

• Membrane and Water Treatment
• /
• v.10 no.2
• /
• pp.155-163
• /
• 2019

The roles of polypropylene (PP) beads and pH on membrane fouling and treatment efficiency were investigated in a hybrid advanced water treatment process of tubular carbon fiber membranes (ultrafiltration (UF) or microfiltration (MF)) and PP beads. The synthetic feed including humic acid and kaolin flowed inside the membrane, and the permeated contacted the PP beads fluidized in the space between the membrane and the module with UV irradiation and periodic water back-flushing. In the hybrid process of UF ($0.05{\mu}m$) and PP beads, final resistance of membrane fouling ($R_f$) after 180 min increased as PP beads increased. The turbidity treatment efficiency was the maximum at 30 g/L; however, that of dissolved organic matters (DOM) showed the highest at PP beads 50 g/L. The $R_f$ strengthened as pH of feed increased. It means that the membrane fouling could be inhibited at low alkali condition. The treatment efficiency of turbidity was almost constant independent of pH; however, that of DOM showed the maximum at pH 5. For MF ($0.1{\mu}m$), the final $R_f$ was the minimum at PP beads 40 g/L. The treatment efficiencies of turbidity and DOM were the maximum at PP beads 10 g/L.

• Ocean and Polar Research
• /
• v.42 no.4
• /
• pp.293-301
• /
• 2020

Blades of tidal stream turbines have to sustain many different loads during operation in the underwater environment, so securing their structural safety is a key issue. In this study, we focused on periodic loads due to wave orbital motion and propose a load reduction method with a blade design. The flap of an airplane wing is a well-known structure designed to increase lift, and it can also change the load distribution on the wing through deflection. For this reason, we adopted a passive flap structure for the load reduction and investigated its effectiveness by an analytical method based on the blade element moment theory. Flap torsional stiffness required for the design of the passive flap can be obtained by calculating the flap moment based on the analytic method. Comparison between a flapped and a fixed blade showed the effect of the flap on load reduction in a high amplitude wave condition.

• International Journal of High-Rise Buildings
• /
• v.10 no.2
• /
• pp.149-164
• /
• 2021

Most of high-rise buildings in Japan^*1 are structure with damping systems recently. The design procedure is performance-based design (PBD), which is based on the nonlinear response history procedure (NRHP) using 2 or 3-dimentional frame model. In addition, hysteretic property of steel plates or velocity-dependent property of viscous dampers are common practice for the damping system. However, for the selection of damping system, the easy dynamic analysis of recent date may lead the most of engineers to focus attention on the maximum response only without thinking how it shakes. By nature, the seismic design shall be to figure out the action of inertia forces by complex & dynamic loads including periodic and pulse-like characteristics, what we call seismic ground motion. And it shall be done under the dynamic condition. On the contrary, we engineers engineers have constructed the easy-to-use static loads and devoted ourselves to handle them. The structures with damping system shall be designed considering how the stiffness & damping to be applied to the structures against the inertia forces with the viewpoint of dynamic aspect. In this paper we reconsider the role of damping in vibration and give much thought to the basic of shake with damping from a standpoint of structural design. Then, we present some design examples based on them.

• International Journal of Computer Science & Network Security
• /
• v.21 no.5
• /
• pp.84-89
• /
• 2021

Medical tests are very important part of the health monitoring process. It is performed for various reasons like diagnosing diseases, determining medications effectiveness, etc. Due to that, patients should be able to read and understand the available online tests and results in order to take proper decisions regarding their health condition. In fact, people are varying in their educational level and health backgrounds that make providing such information in an easily readable format by the majority of people considered as a challenge in the health domain since ever. This paper describes the MTReadable corpus which constructed for evaluating the readability of online medical tests. It covered 32 basic periodic check-up tests with over 36k words. These tests information are annotated and labelled based on three readability levels which are easy, neutral and difficult by three non-specialists native Arabic speakers. This paper contributes to enriching the Arabic health research community with an investigation of the level of readability of online medical tests and to be a baseline for further complex health online reports and information.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.423-433
• /
• 2020

Direct current (DC) electric fields have been used for electro-osmotic dewatering. Under DC conditions, however, the electrical contact resistance between the electrode and the dewatering material increases considerably during the process of dewatering. Such a circumstance hinders the continuation of effective electro-osmotic dewatering. To reduce this hindrance, an applied pulse electric field with periodic reversals of the electrode polarity should improve electro-osmotic dewatering. In this study, electro-osmotic dewatering under pulse conditions was experimentally investigated for electrode polarity reversals. During the dewatering process, the pulse electric field was able to reduce the hindrance caused by the DC, resulting in an increased final dewatered amount relative to that under a DC electric field. For a constant applied voltage, the reversed polarity condition, under which the electric current passing through the material was almost unchanged with time, yielded the maximum final dewatered amount. This technique can be used to enhance drainage from a water storage facility during a period of extreme drought and the seawater desalination plants using reverse osmosis in drought stricken coastal regions.