• 한국화재소방학회논문지
• /
• 제31권2호
• /
• pp.1-8
• /
• 2017

샌드위치패널은 건축물의 내 외벽 및 지붕구조에 사용되며 양면의 불연성재료와 단열용 심재로 구성된 복합자재이다. 뛰어난 단열성능과 경량 및 시공의 우수한 특성 대비 화재 시 패널간 결합부위를 통해 화염이 내부로 유입되어 심재가 쉽게 용융되며 급격한 화염확산으로 인명 및 재산피해를 발생시킨다. 현행 건축법은 건축물 마감재료에 대하여 소규모 시험편에 대한 화재시험방법으로 연소성능을 파악하며 규정한 성능기준에 합격한 제품을 사용하도록 한다. 외벽 마감재료의 경우 불연 준불연 성능확보 재료를 사용하거나 화재확산방지구조를 설치하도록 규정한다. 본 연구는 외벽 마감재료에 국한되어 적용하고 있는 화재확산방지 구조를 샌드위치패널 건축물에 적용하여 수평 수직 화재확산의 위험성의 차이를 확인하고자 하였다. 이에 샌드위치패널에 대하여 ISO 13784-1 시험방법을 통한 실물화재실험과 금속구조물을 이용하여 패널간 화염확산을 차단하는 시공을 통해 화염확산방지 적용 여부에 대한 연소거동과 그 효과를 측정하였다. 실험 결과 패널 조인트 부위의 화염확산방지구조 시공은 패널 내부의 화염확산을 지연하며 이에 따른 플래시오버 시간이 지연되어 복합자재 건축물의 화재안전확보에 중요한 요인으로 작용될 수 있음을 확인하였다.

• 한국산학기술학회논문지
• /
• 제10권12호
• /
• pp.3632-3637
• /
• 2009

본 논문에서는 단상 MJ81 전기선로전환기의 실용화를 위해 요구되는 현장설치시험을 수행한 결과를 기술하고 있다. 이러한 단상 MJ81 전기선로전환기는 경부고속철도 건설시에 프랑스 알스톰 및 코지프로부터 기술이전 받아 국산화한 3상 MJ81 전기선로전환기를 단상 220V를 사용하고 있는 국내 기존선에서도 선로 연변 전원설비의 변경 없이도 사용할 수 있도록 구동부의 성능 개선을 통해 공인인증시험을 통과한 제품이다. 한국철도기술연구원 및 삼성 SDS에서는 기존철도기술개발사업을 통해 기존선의 속도 및 안전성 향상을 위해 단상 MJ81 전기선로전환기를 국산화 하였으나 이의 실용화를 위해서는 연동장치와의 인터페이스 시험 뿐 아니라 실제 선로에서의 현장설치시험을 통해 성능을 입증하여야 한다. 본 논문에서는 이러한 시험을 진행한 과정과 함께 현장설치시험의 결과 분석을 통해 국산품인 단상 MJ81 전기선로전환기의 실용성을 입증하였으며, 입증된 결과를 바탕으로 2009년 2월 한국철도시설공단의 물량을 수주하여 현재 설치 중이다.

• 농업과학연구
• /
• 제42권4호
• /
• pp.389-396
• /
• 2015

This study was performed to investigate the opinions of various related-industries on ban of antibiotics growth promoters (AGPs) in commercial mixed feed. The answers on a total of 21 questions were summarized by response number and percentage. 93% of those surveyed were in agreement of a ban of dietary AGPs. The agreement reasons were the livestock safety (61.5%), the reduction of antibiotic use (23.1%), and decrease of antibiotic-resistant bacteria (11.5%). The negative effects expected by the ban of AGPs were poor growth performance (44.2%), elevated disease emergence (31.4%), increasing the feed cost (18.6%), and quality degradation of livestock (5.8%). As the efficient plans for decline of AGPs use, the feeding environment improvement was the highest with 43%, and farmer training and the consolidation inspection of residual substance on antibiotics in livestock product was 27.9% and 22.1%, respectively. 46.5% of respondent are considering the modification of feed spec and 39.5% of those surveyed have staged a modified feed spec. In conclusion, livestock related-industries approve a ban of AGPs, and they assert that the policy support, improvement of management and environment in the farm, providing technology from related-industries are multiply essential for a stable settlement of a ban policy of AGPs.

• 수산해양기술연구
• /
• 제58권1호
• /
• pp.10-18
• /
• 2022

Fishery sea anchor is widely used for many fishing vessels. However, standardization of the dimension and terminology of the fishery sea anchor has not been achieved, reducing the reliability of the performance and safety of the fishery sea anchor. Therefore, this study researches the reality of usage of fishery sea anchor and then attempts to suggest the development direction of the standard draft as basic data. As a result of the survey on the reality of usage show that various terms were used for each part of the fishery sea anchor (including the incorrect form of non-standard words derived from Japanese) and that the production of this product in the fishery sea anchor market was concentrated on one specific manufacturer. In addition, the main specifications of the fishery sea anchor are set and manufactured based on conventional experience without standards. In the field, there was no standardized drawing for fishery sea anchor and users had low awareness of the main specifications of fishery sea anchor. Therefore, this study suggested the following regarding the fishery sea anchor: standard terms for each part including Korean and English names and standard drawing of sea anchor. It is hoped that this study will contribute to research for the standardization of fishery sea anchor, which will increase in reliability and lead to increased interest in standardization in the fishery field.

• Design & Manufacturing
• /
• 제10권1호
• /
• pp.41-45
• /
• 2016

Electrical equipment in factories, buildings, etc. with the development of the industry has become a large capacity. By the development, electric load also become diversified and there is also highly functional requirements being electrical equipment. Particularly in the small and medium-sized circuit breakers, tend to preferentially consider the economy stands out and improvements in safety, ease of mounting and connection through the modularity of the basic dimensions compact and cost to block expansion of the scope of the development of capacity, etc. The product having a competitive has been strongly required. In order to implement the circuit breakers of breaking capacity and compact at the same time taking into account the economic development of this technology applied to the current-limiting mechanism is essential budget or the current limiting mechanism is currently available mechanisms applicable to small and medium-sized frame (frame) can not do it. In this paper, at the same time satisfying the economic efficiency, by minimizing the load force of the moving contactor (moving contactor) to be applied to small and medium frame other hand to secure the economical efficiency without using high speed contact parting acceleration of the moving contactor conventional current-limiting mechanism, and to develop a current-limiting mechanism that can be satisfied with the same or higher performance to meet the needs of the market.

• Nuclear Engineering and Technology
• /
• 제54권8호
• /
• pp.2792-2800
• /
• 2022

In the core of the WWR-K reactor, a long-term irradiation of tristructural isotopic (TRISO)-coated fuel particles (CFPs) with a UO₂ kernel was carried out under high-temperature gas-cooled reactor (HTGR)-like operating conditions. The temperature of this TRISO fuel during irradiation varied in the range of 950-1100 ℃. A fission per initial metal atom (FIMA) of uranium burnup of 9.9% was reached. The release of gaseous fission products was measured in-pile. The release-to-birth ratio (R/B) for the fission product isotopes was calculated. Aspects of fuel safety while achieving deep fuel burnup are important and relevant, including maintaining the integrity of the fuel coatings. The main mechanisms of fuel failure are kernel migration, silicon carbide corrosion by palladium, and gas pressure increase inside the CFP. The formation of gaseous fission products and carbon monoxide leads to an increase in the internal pressure in the CFP, which is a dominant failure mechanism of the coatings under this level of burnup. Irradiated fuel compacts were subjected to electric dissociation to isolate the CFPs from the fuel compacts. In addition, nondestructive methods, such as X-ray radiography and gamma spectrometry, were used. The predicted R/B ratio was evaluated using the fission gas release model developed in the high-temperature test reactor (HTTR) project. In the model, both the through-coatings of failed CFPs and as-fabricated uranium contamination were assumed to be sources of the fission gas. The obtained R/B ratio for gaseous fission products allows the finalization and validation of the model for the release of fission products from the CFPs and fuel compacts. The success of the integrity of TRISO fuel irradiated at approximately 9.9% FIMA was demonstrated. A low fuel failure fraction and R/B ratios indicated good performance and reliability of the studied TRISO fuel.

• 한국소음진동공학회논문집
• /
• 제23권12호
• /
• pp.1045-1055
• /
• 2013

It is true that the dependency on import is currently high in case of the safety checkup system of domestic airplanes, and it is at the point of time that localization of HUMS for small airplanes is required. In this study, the design factors were selected for the lightweight of HUMS for small airplanes by using Pro-Engineer which is a design tool and Abaqus. 9 models were made through experiment plans with Taguchi method for this, and the each model for weight lightening was selected through vibration analysis and shock analysis while in operation with experiment profile values. After fabricating HUMS, it was verified that as a result of experiment with the same profile values as the analysis, there was similarity between the analyzed values and values of the experiment. As a result of performing weight lightening which is the purpose of the study, electronic performance for small airplanes is assured and a design plan reducing 15 % weight compared to the targeted weight was deduced. Besides, it could be verified that the light weight model satisfied the maximum allowable displacement value of PCB[printed circuit board] and accordingly satisfied electronic properties of HUMS. In this study, the reliability of a product was certified through the result of an experiment on ground. If the reliability of HUMS were verified through a test flight in the future, it is considered that it would make a big contribution to localization of aerospace electronic equipment.

• 센서학회지
• /
• 제26권1호
• /
• pp.39-43
• /
• 2017

Development of vision system as a nondestructive evaluation system can be very useful in screening the defective mechanical parts before they are assembled into the final product. Since the tens of thousands of the mechanical parts are used in an automobile carefully inspecting the quality of the mechanical parts is very important to maximize the performance of the automobile. To sort out the defective mechanical parts before they are assembled, auto parts fabrication companies employ various inspection systems. Nondestructive evaluation systems are getting rapidly popular among various inspection systems. In this study, we have developed a vision system to inspect the inside of the brake caliper, a part that is used to compose a brake which is the most important to the safety of the drivers and the passengers. In a brake caliper, a piston is pushed against the brake disk by oil pressure, causing a friction to damp the rotation of the wheel. Inside the caliper, a groove is positioned to adopt an oil seal to prevent the oil leaks. Inspecting the groove with our vision system, we could examine the existence of the contaminants which are normally the residual tiny pieces from the machining process. We used a high resolution GigE camera, 360 degree lens to look in the inside view of the caliper at once, and a special illumination system in this vision system. We used the edge detection technique to successfully detect the contaminants which were in the form of small metal chips. Labview graphical program was used to process the digital data from the camera and to display the vision and the statistics of the contaminants. We were very successful in detecting the contaminants from the various size calipers. We think we are ready to employ this vision system to the caliper production factories.

• 소성∙가공
• /
• 제30권6호
• /
• pp.291-300
• /
• 2021

Currently, starting with electric vehicles, the application of ultra-high-strength steel sheets and light metals has expanded to improve mileage by reducing vehicle weight. At a time when internal combustion engine vehicles are rapidly changing to electric vehicles, the application of ultra-high-strength steel is expanding to satisfy both weight reductions and the performance safety of the chassis parts. There is an urgent need to improve the quality of parts without defects. It is particularly difficult to estimate the part formability through the finite element method (FEM) in the burring operation, so product design has been based on the hole expansion ratio (HER) and experience. In this study, design of experiment (DOE), analysis of variance (ANOVA), and regression analysis were combined to optimize the formability by adjusting the process variables affecting the burring formability of ultra-high-strength steel parts. The optimal variables were derived by analyzing the influence of variables and the correlation between the variables through FE analysis. Finally, the optimized process parameters were verified by comparing experiment with simulation. As for the main influence of each process variable, the initial hole diameter of the piercing process and the shape height of the preforming process had the greatest effects on burring formability, while the effect of a lower round of punching in the burring process was the least. Moreover, as the diameter of the initial hole increased, the thickness reduction rate in the burring part decreased, and the final burring height increased as the shape height during preforming increased.

• 한국산업융합학회 논문집
• /
• 제20권5호
• /
• pp.359-364
• /
• 2017

A machine such as bean crusher machine is subjected to different loads and vibration. Due to this vibration there will be certain deformations which affect the performance of the machine in adverse manner. This paper proposed a vibration analysis of bean crusher machine using ANSYS. The Finite Element Method (FEM) analysis is carried out to study the effect of vibration on the structure in order to ensure the safety. This work helps the machine developer make a better product at the early design stage with lower cost and faster development time. To do this, firstly, using Inventor, a CAD model is prepared. Secondly, the analysis is to be carried out using ANSYS 15. The modal analysis and random vibration analysis of the structure was conducted. The analysis shows that the proposed design was successfully shows the minimum deformation when the vibration was applied in normal condition.