• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.11-14
• /
• 2007

Noise level and Airflow amount of a kitchen hood are affected by the conditions of airflow path. Thus this study is expected to be used as a basic reference in designing airflow path of apartment housing throughout analysing changes in noise level and airflow amount from the various conditions of airflow path. Noise level generated by the kitchen hood is estimated in a kitchen and a living room of two constructed apartment houses, and an experiment is conducted in an half anechoic chamber to analyze noise level and airflow amount by the different length, diameter and number of windings of a round shaped soft duct which is connected to the kitchen hood. The measured results in apartment houses show that the noise level in both apartments exceeds the NC standard greatly in living spaces. In apartment A, a regular apartment house, the noise level was $NC-65{\sim}75$, $NC-45{\sim}60$ and NC-70, NC-45 in the kitchen and living room with an operation of kitchen hood in 1 and 3 stages. In apartment B, an apartment complex, the noise level was NC-55 and NC-60 in the kitchen and living room with an operation of kitchen hood in 3 stages. In particular, there was an increase of noise level at 125Hz-band resulted from an amplification of sound, which requires adequate measures in noise reduction. The results measured in Half anechoic chamber show 99% of airflow amount increase with the modification of a duct' s diameter from ${\Phi}$ 100mm to ${\Phi}$ 125mm, 37% of airflow amount increase with the modification of a duct' s diameter from ${\Phi}$ 125mm to ${\Phi}$ 150mm, and 173% of airflow amount increase with the modification of a duct' s diameter from ${\Phi}$ l00mm to ${\Phi}$ 150mm. The noise level was lower than the level measured in apartment housing about 20 in NC-value and 11.4 in dB(A)-value, which was interpreted as the effect of the load by the pressure condition at the rear end of the duct. Also, an amplification of sound in 125Hz-band influenced NC-value considerably, therefore effective measure is needed.

• Journal of Broadcast Engineering
• /
• v.15 no.1
• /
• pp.63-75
• /
• 2010

In this paper, the equalizer techniques that is able to adopt the digital on-channel repeater for 8VSB-based DTV system has been analyzed and we propose an effective equalizer structure which can reduce the error propagation phenomenon by the feedback signal and improve the receiver performance at the same time. In order to confirm the effective cancellation of the feedback signal, the multi-level Correlation LMS scheme is proposed through the analysis of conventional basic LMS based DFE and Correlation LMS algorithm and as compared with the conventional method, we can confirm the reduction of error propagation. When performing the computer simulation, as the Brazil channel model which is very popular for DTV broadcasting system is adopted, the result is drawn by comparing and analysing the equalizer algorithm. We have examine the symbol error rate which is in the range of 15~25dB of operation receipt SNR and MSE(Mean Square Error) in the DTV broadcasting system. As a result of comparing with the existing method, the signal-noise ratio which is necessary for maintain the bit error correction ability that the means of proposal is same is reduced by about 2~5dB, and in the rate of convergence through the MSE, we found the reduction of needed time.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.2
• /
• pp.447-454
• /
• 2011

Power-line interference(PLI) can distort certain regions in analysing the ECG signal. In particular, the regions such as P and R wave that are important element in diagnosing with arrhythmia is expressed as different type of noise according to the case whether power-line frequency is multiples of sampling frequency and or not. Noise characteristics is also divided into linearity and non-linearity. In this paper, adaptive subtraction method for removing variable PLI of ECG signal is proposed. We classify the multiple relationship between power line and sampling frequency as Multiple and Non-multiple. PLI of Linear segment is extracted through moving average filter, PLI of non-linear segment is extracted through the interference component that is extracted in the linear segment and stored in the temporary buffer. The performance of P wave and R wave detection is evaluated by using 119 data record of MIT-BIH arrhythmia database. The achieved scores indicate P wave detection rate of 97.91%, R wave detection rate of 96.66% and P wave detection rate of 99.01%, R wave detection rate of 97.93% accuracy respectively for Notch filter and proposed subtraction method.

• Korean Journal of Remote Sensing
• /
• v.13 no.1
• /
• pp.13-30
• /
• 1997

Recent improvements of satellite remote sensing sensors which are represented by hyperspectral imaging sensors and high spatial resolution sensors provide a large amount of data, typically several hundred megabytes per one scene. Moreover, increasing information exchange via internet and information super-highway requires the developments of more active service systems for processing and analysing of remote sensing data in order to provide value-added products. In this sense, an advanced satellite data processing system is being developed to achive high performance in computing speed and efficieney in processing a huge volume of data, and to make possible network computing and easy improving, upgrading and managing of systems. JAVA internet programming language provides several advantages for developing software such as object-oriented programming, multi-threading and robust memory managent. Using these features, a satellite data processing system named as GeoPixel has been developing using JAVA language. The GeoPixel adopted newly developed techniques including object-pipe connect method between each process and multi-threading structure. In other words, this system has characteristics such as independent operating platform and efficient data processing by handling a huge volume of remote sensing data with robustness. In the evaluation of data processing capability, the satisfactory results were shown in utilizing computer resources(CPU and Memory) and processing speeds.

• The Journal of the Korea Contents Association
• /
• v.21 no.11
• /
• pp.234-242
• /
• 2021

The purpose of this study was to examine the effectiveness of drama therapy in Korea by using method of meta-analysis. For the purpose of this study, master's theses, doctoral dissertations, and journal articles published in Korea up to June, 2021 were systematically reviewed. As a result, a total of 18 studies were eligible for the inclusion criteria. The mean effect sizes and test for homogeneity of effect size(Q-statistic) were analyzed by using Comprehensive Meta-Analysis Software 2.0. The main findings of the study were as follows. First, the average effect sizes for drama therapy were ES=1.325 of self-esteem, ES= -1.230 of depression and anxiety, ES= 1.025 of stress, ES=1.018 of sociability, Es=0.907 of emotional intelligence, ES= 0.897 of psychological wellbeing. Second, by analysing the moderate variables of the effect size for drama therapy, 'adult', 'the number of session' 'performance based drama therapy' of self esteem were statistically significant. Based on this study results, the drama therapy research and practice implications in Korea were discussed.

• The Journal of Korean Physical Therapy
• /
• v.3 no.1
• /
• pp.9-37
• /
• 1991

The purpose of this . study is to examine the unsatisfactory factors of the physical therapists and to obtain the materials necessary to comply with these factors by analysing their service performance and job satisfaction, To accomplish these purposes, this study was carried out by using the questionnaires 206 physical therapists registered in the Korean Physical Therapists Association, for 35 days from January 7 to February 10, 1990. The result of this study is summarized as follows. 1. Of total respondents, the male accounted for 54.4 percent, while the female for 45.6 percent. Their age showed that 20s accounted for 65.0 percent, while the service period less than 3 years accounted for 66.5 percent. In addition, 63.6 percent of them served at the general clinics. 2. The general clinics caused the physical therapists to serve for 10 hours or more per day, where their therapy room located in the underground accounted for 41.3 percent. Their health diagnosis status indicated that nondiagnosis accounted for 63.2 percent. The number of the served patients fer a day showed that 20-30 accounted for 37.4 percent, while 30 persons or more for 25.7 percent. 53.4 percent of total subjects was unsatisfied with their duty quantity. And, the monthly salary indicated that 500,000 or less accounted for 72.3 percent. 3. The average marks by their job satisfaction factors indicated 4.42 for duty importance, 4.02 for recognization of specialized job, 3.98 for ability exercise, 1.99 for promotion possibility, 2.28 for reasonable salary, and 2.41 for welfare system, respectively, based on 5 full marks. 4. The summarized job satisfaction by factors indicated that the relation with the doctor accounted for 57.8 percent, the satisfaction status with the existing job for 53.4 percent, the ability development for 41.8 percent, respectively, and the salary for 10.2 percent. Then, the satisfaction by sex showed that the male was generally satisfied with the ability development (p<0.05), the relation with the doctor (p<0.01), and the satisfaction with the existing job, while the female was satisfied with the duty quantity(p<0.05), salary, and the situation guarantee (p<0.05). On the other hand, the satisfaction by age indicated that the subject of the lower age were satisfied with the ability development (p<0.01), the relation with the doctor(p<0.05), the salary, and the situation guarantee. Also, the satisfaction by the service section showed that the physical therapists serving at the general hospital were satisfied with the ability development (p<0.01), the duty quantity (p<0.01), the salary(p<0.01), the situation guarantee(p<0.01), and the satisfaction with the existing duty (p<0.05), while the physical therapists at the hospital and the rehabilitation center were unsatisfied with the salary (p<0.01). In addition, The satisfaction with the service period at the existing section indicated that the physical therapists less than 3 years were highly satisfied with the ability development, the relation with the doctor, the situation guarantee, and the existing duty(p<0.05), while the physical therapists more than 6 years tended to show the lower satisfaction, And the satisfaction with the monthly salary indicated that the higher the monthly salary, the higher the satisfaction with the relation to the doctor(p<0.05), the duty quantity(p<0.01), the salary(p<0.01), and the situation guarantee (p<0.01). 5. The correlation between general characteristics and job satisfaction factors indicated that the sex was directly correlated to the marital status (r=-0.442), while it was reversely correlated to the age (r=-0.564) , total career (r=-0.229), and the relation with the doctor (r=-0.233). Additionally, the age was directly correlated to the total carreer (r=-0.677), and the service period at the existing section (r=0.491), while the age was reversely correlated to the marital status (r=-0.678). Accordingly, the higher job satisfaction of the physical therapists was related to factors such as their duty importance, recognization of specialized occupation, ability exercise, autonomy, relation to colleagues, decision-making's consideration, and relation with the doctor, while the lower job satisfaction includes the opportunity of promotion, salary, welfare system, service time, duty quantity, and situation guarantee. For this reason, if the factors of the lower job satisfaction are solved, then it will be possible to encourage the motive of these physical therapists, and the acyivate their duties. More over, it is also possible to improve the medical service, Additionally, if the general physical therapy room in the hospital and in the public health center are established, more development should be accomplished in the physical therapy.

• (The) Research of the performance art and culture
• /
• no.19
• /
• pp.161-190
• /
• 2009

This study presents matters of how to analyse the dance of artistic form on the course of transforming folk art to be separated from leisure to become the art form. In particular, the traditional art of dance in Korea has been of collective act like dureh, rather than of individual art, that it had to choose the repeated style of same form and rhythm. In this respect, before it can be said that the dance in its own form became more sophisticated and adopted the artistic segment in the time of modernisation, it is viewed that in the very heart of folk dance there was sufficient ability of artistic material to seek its own right. In this regard, the artistic transformation of seoljanggo nori into seoljanggo dance is an art form which is found in Korea, and expressing rhythm and playfulness is evident and sought attention. Therefore this study puts its importance in analysing how, in the aspect of the course of life of traditional arts, dance is formed in its own right and developed a form of art from fun entertainment. I have chosen, among them, seoljanggo, which used to be a form of fun entertainment and later transformed into a form of art on stage, in particular LeeGyeongh wa seoljanggo dance which maintains the style of Honam Udo farmers' music, and tried to read the text from it. It has resulted in that, Lee Gyeonghwa seoljanggo dance did a new try on tradition, in its development of expressing art through dance and onto more technical sophistication, found in the style of tune and choreography fused into its distinctive form. The art of traditional dance concerns here that seoljanggo has changed from agrarian entertainment to modern stage art, which shows how tradition can be adopted to the contemporary cultural life or to be reinvented to the needs of the aesthetic style that the current society consumes. Thus, it is necessary to think about its role in education and to represent cultural creativity from local developments.

• Journal of Biosystems Engineering
• /
• v.2 no.1
• /
• pp.7-24
• /
• 1977

This paper is the forth and fifth one of the study on balanced type oscillating mole drainer. In the light of the results from previous reports about the model tests, some design criteria were established and a prototype machine was set up for experimental purpose. Motion characteristics and functionof the each parts of the machine were checked and analyzed. After that, performance tests of the prototype machine were carried out in thefield. Obtained results are summarized as follows ; 1. Ten centimeter of the bullet diameter was determined so as to be able to attach it to the tractors with capacity of 30 PS to 40 PS. 2. To maintain the balance between the moments of the front shank and rear shank, the oscillating amplitude of the rear bullet was determined to be larger than that of the front bullet. At the same time , the oscillating direction of the rear bullet was designed with the inclines of ten to thirty degrees. 3. An octagonal dynamo transduced was developed for measuring the compressive force of the upper link is measuring the draft force of the machine. Acceptable linear relationship between forces and strain responses from O.D.T. was obtained. 4. Analysing the balancing mechanism of the acting part of the machine , it was found that the total draft force of the machine was equal to the difference between the sum of the draft force produced from the right and left side bending moments of the lower drawber and the compressive force on the upper link. 5. There are acceptable linear relationship between the strain and twisting moment by driving shaft, and between strain and shank moment. Above results enable us to carry out the field experiment with prototype machine. 6. When the test machine was used in the field, it was possible to reduce the oscillating acceleration by forty percent in average as compared it with the single bullet mole drainer. 7. When the test machine was used under the oscillating condition, the dratt torce was reduced by 27 percent to 59 percent as compared it with the test machine under non-oscillating condition, while the draft force was increased by 7 percent to 20 percent as compared it with the mole drainer having oscillating single bullet. The reasoning behind this fact was considered as the resistance force due to the rear shank and bullet. 8. As the amplitude and frequency of the bullet were increased, the torque was increased accordingly. This tendency could be varied with the various characteristics of the given soils. And the larger frequency and amplitute, the more increasing oscil\ulcornerlating power but decreasing draft brce were needed, and draft force was increased as the velocity was increased.9. When the amplitude of the rear bullet was designed to be larger than that of the front bullet, the minimum value of the moment was lowered and oscillating acceleration was reduced. And when the oscillating direction of the rear bullet was declined back\ulcornerwards, oscillating acceleration was increased along with the increasing angle of decli\ulcornernation. When the test machine was operated in high speed, the difference between maximum moments and minimum ones became narrow. This varying magnitude of moments appeared on the moment oscillogram seems to be correlated to the oscillating acceleration and draft force. 10. From the analysis of variance, it was found that those factors such as frequency, amplitude, and operating velocity significantly affected in the oscillating acceleration, the draft resistance, the torque, the moment, and the total power required. And interaction between frequency and amplitude affected in the oscillating acceleration. 11. Within the given situation of this study, the most preferable operating conditions of the test machine were 7 Hz in oscillating frequency, 0.54 m/sec in operating velocity, and 39.1 mm in oscillating amplitude of front and rear bullets. However, it is necessary to select the proper frequency and magnitude of oscillation depending on the soil properties of the field in which the mole drainer is practiced by use of a bal1nced type oscillating mole drainer. 12. It is recommended that a comparative study of the mole drainers would be performed in the near future using two separate balanced oscillating bullet with the one which is operated by oscillating the movable bullet in a single cylinder or other balanced type which may be single oscillating bullet with spring, damper or balancing weight, and that of thing. To expand the applicability of the balanced type oscillating mole drainer in practical use, it is suggested to develop a new mechanism which perform mole drain with vinyl pipe or filling material such as rice hull.

• Journal of the Korean Society for Library and Information Science
• /
• v.12
• /
• pp.269-327
• /
• 1985

This study was undertaken to meet more fully the demands for improved training of library personnel, occasioned by the rapidly changing roles and functions of libraries as they try to adapt to the vast social, economic and technological changes currently in progress in the Korean society. The specific purpose of this research is to develop a standard curriculum at the batchelor's level that will properly equip the professional personnel in Korean libraries for the changes confronting them. This study started with the premise that to establish a sound base for curriculum development, it was necessary first to determine what concepts, knowledge, and techniques are required for professional library personnel to perform it at an optimal level of efficiency. Explicitly, it was felt that for the development of useful curricula and courses at the batchelor's level, a prime source of knowledge should be functional behaviours that are necessary in the job situation. To determine specifically what these terminal performance behaviours should be so that learning experience provided could be rooted in reality, the decision was reached to use a systems approach to curriculum development, which is an attempt to break the mold of traditional concepts and to approach interaction from an open, innovative, and product-oriented perspective. This study was designed to: (1) identify what knowledge and techniques are required for professional library personnel to perform the job activities in which they are actually engaged, (2) to evaluate the educational needs of the knowledge and techniques that the professional librarian respondents indicate, and (3) to categorise the knowledge and techniques into teaching subjects to present the teaching subjects by their educational importance. The main data-gathering instrument for the study, a questionnaire containing 254 items, was sent to a randomly selected sample of library school graduates working in libraries and related institutions in Korea. Eighty-three librarians completed and returned the questionnaire. After analysing the returned questionnaire, the following conclusions have been reached: (A) To develop a rational curriculum rooted in the real situation of the Korean libraries, compulsory subjects should be properly chosen from those which were ranked highest in importance by the respondents. Characters and educational policies of, and other teaching subjects offered by, the individual educational institution to which a given library school belongs should also be taken into account in determining compulsory subjects. (B) It is traditionally assumed that education in librarianship should be more concerned with theoretical foundations on which any solution can be developed than with professional needs with particulars and techniques as they are used in existing library environments. However, the respondents gave the former a surprisingly lower rating. The traditional assumption must be reviewed. (C) It is universally accepted in developing library school curricula that compulsory subjects are concerned with the area of knowledge students generally need to learn and optional subjects are concerned with the area to be needed to only those who need it. Now that there is no such clear demarcation line provided in librarianship, it may be a realistic approach to designate subjects in the area rated high by the respondents as compulsory and to designate those in the area rated low as optional. (D) Optional subjects that were ranked considerably higher in importance by the respondents should be given more credits than others, and those ranked lower might be given less credits or offered infrequently or combined. (E) A standard list of compulsory and optional subjects with weekly teaching hours for a Korean library school is presented in the fourth chapter of this report.

• Journal of Global Scholars of Marketing Science
• /
• v.18 no.4
• /
• pp.119-155
• /
• 2008

Customer Relationship Management(CRM) has been a sustainable competitive edge of many companies. CRM analyzes customer data for designing and executing targeted marketing analysing customer behavior in order to make decisions relating to products and services including management information system. It is critical for companies to get and maintain profitable customers. How to manage relationships with customers effectively has become an important issue for both academicians and practitioners in recent years. However, the existing academic literature and the practical applications of customer relationship management(CRM) strategies have been focused on the technical process and organizational structure about the implementation of CRM. These limited focus on CRM lead to the result of numerous reports of failed implementations of various types of CRM projects. Many of these failures are also related to the absence of marketing approach. Identifying successful factors and outcomes focused on marketing concept before introducing a CRM project are a pre-implementation requirements. Many researchers have attempted to find the factors that contribute to the success of CRM. However, these research have some limitations in terms of marketing approach without explaining how the marketing based factors contribute to the CRM success. An understanding of how to manage relationship with crucial customers effectively based marketing approach has become an important topic for both academicians and practitioners. However, the existing papers did not provide a clear antecedent and outcomes factors focused on marketing approach. This paper attempt to validate whether or not such various marketing factors would impact on relational quality and CRM performance in terms of marketing oriented perceptivity. More specifically, marketing oriented factors involving market orientation, customer orientation, customer information orientation, and core customer orientation can influence relationship quality(satisfaction and trust) and CRM outcome(customer retention and customer share). Another major goals of this research are to identify the effect of relationship quality on CRM outcomes consisted of customer retention and share to show the relationship strength between two factors. Based on meta analysis for conventional studies, I can construct the following research model. An empirical study was undertaken to test the hypotheses with data from various companies. Multiple regression analysis and t-test were employed to test the hypotheses. The reliability and validity of our measurements were tested by using Cronbach's alpha coefficient and principal factor analysis respectively, and seven hypotheses were tested through performing correlation test and multiple regression analysis. The first key outcome is a theoretically and empirically sound CRM factors(marketing orientation, customer orientation, customer information orientation, and core customer orientation.) in the perceptive of marketing. The intensification of ${\beta}$coefficient among antecedents factors in terms of marketing was not same. In particular, The effects on customer trust of marketing based CRM antecedents were significantly confirmed excluding core customer orientation. It was notable that the direct effects of core customer orientation on customer trust were not exist. This means that customer trust which is firmly formed by long term tasks will not be directly linked to the core customer orientation. the enduring management concerned with this interactions is probably more important for the successful implementation of CRM. The second key result is that the implementation and operation of successful CRM process in terms of marketing approach have a strong positive association with both relationship quality(customer trust/customer satisfaction) and CRM performance(customer retention and customer possession). The final key fact that relationship quality has a strong positive effect on customer retention and customer share confirms that improvements in customer satisfaction and trust improve accessibility to customers, provide more consistent service and ensure value-for-money within the front office which result in growth of customer retention and customer share. Particularly, customer satisfaction and trust which is main components of relationship quality are found to be positively related to the customer retention and customer share. Interactive managements of these main variables play key roles in connecting the successful antecedent of CRM with final outcome involving customer retention and share. Based on research results, This paper suggest managerial implications concerned with constructions and executions of CRM focusing on the marketing perceptivity. I can conclude in general the CRM can be achieved by the recognition of antecedents and outcomes based on marketing concept. The implementation of marketing concept oriented CRM will be connected with finding out about customers' purchasing habits, opinions and preferences profiling individuals and groups to market more effectively and increase sales changing the way you operate to improve customer service and marketing. Benefiting from CRM is not just a question of investing the right software, but adapt CRM users to the concept of marketing including marketing orientation, customer orientation, and customer information orientation. No one deny that CRM is a process or methodology used to develop stronger relationships being composed of many technological components, but thinking about CRM in primarily technological terms is a big mistake. We can infer from this paper that the more useful way to think and implement about CRM is as a process that will help bring together lots of pieces of marketing concept about customers, marketing effectiveness, and market trends. Finally, a real situation we conducted our research may enable academics and practitioners to understand the antecedents and outcomes in the perceptive of marketing more clearly.