• Journal of Korean Society of Transportation
• /
• v.35 no.3
• /
• pp.210-219
• /
• 2017

Electric vehicles, which are attracting attention as eco-friendly vehicles, have been increasing in number since 2011 in Korea. The purpose of this study is to analyze the efficient operation of existing charging stations and factors to consider when installing additional charging stations based on the case of Jeju Island where the electric vehicle penetration rate is high and the charging infrastructure is relatively well established. The characteristics of using electric car charging stations by region, type of facility, and time of day are analyzed. As a result of analyzing the frequency of using the charger installed in Jeju Island, the utilization of both the fast charger and the slow charger is found to be concentrated in a specific area. The usage rate of charger installed in a business facility and a public parking lot is high in both fast charger and slow charger. However, according to the usage rate by time of day, the fast charger has a high utilization rate throughout the afternoon, while the use of a slow charger is concentrated in the morning. In order to enable users to utilize the electric vehicle charging station efficiently, it is necessary to provide a publicity guide for the charging station having a low utilization rate, a notice for using the charger, and a notification of completion of charging. Considering the charging demand, the area where the charger is not yet installed should be considered as the area to install the charger, and in addition, the additional installation should be considered in the area and the facility where the amount of charge is large. Service improvement is expected to be possible by utilizing actual electric vehicle charging behavior analysis result.

• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1263-1269
• /
• 1999

An FBAR(Solidly Mounted Resonator) was fabricated using reflector layers which prohibit the penetration of bulk acoustic wave into substrate. The SMR consisted of top and bottom electrodes(Al films), a piezoelectric layer (ZnO film), reflector layers(W/$Si_2$ films) and Si substrate. The electrodes were deposited by dc sputtering. The piezoelectric layer and the reflector layers were deposited by rf magnetron sputtering. The control of crystallinity, microstructures and electric properties of each layer was essential for attaining the optimum FBAR characteristics. Under the best deposition conditions for FBAR devices, the ZnO films had highly c-axis preferred orientation(${\sigma}=2.17^{\circ}$), resistivity of $10^4\;{\omega}cm$, and surface roughness of 10.6 ${\AA}$. On the other hand, the surface roughness of W and $Si_2$ films was 16 ${\AA}$ and 33 ${\AA}$, respectively, and the resistivity of Al film was $5.1{\times}10^{-6}\;{\Omega}cm$. The SMR devices were fabricated by the conventional semiconductor processes. In the resonance conditions of the SMR, the series resonance frequency (fs) and the parallel resonance frequency(fp) were 1.244 GHz and 1.251 GHz, respectively and the quality factor(Q) was 1200.

• Asia pacific journal of information systems
• /
• v.23 no.4
• /
• pp.29-51
• /
• 2013

In line with network technology development and smart device penetration, the social network service (SNS) has expanded its influence. The SNS which is a service based on communication and sharing among people, has grown based on users' voluntary engagement and participation and its influence has appeared beyond the cyberspace into the overall areas of domestic and foreign culture and society. In particular, SNS-based real-time communication during diverse disasters, can help prevent further damage. By sharing information on social donation activities and environmental campaigns, people have used SNS as a tool to change the society in a more positive way. Such series of activities functioning as a power to change the society have been made much faster and wider through the help of a new media called SNS. To better understand such trends, we are required to study about the SNS and its user relationships first. In this context, this study sought to identify the effects of people's desire to build friendships through SNS on the voluntary and society-friendly activities of people. This study considers online pro-social behavior and proposes online citizenship behavior. Citizenship behavior has been examined in organization context. That is, organizational citizenship behavior explains an employee's pro-social behavior in an organization context. Organizational citizenship behavior is characterized by the individual's helping others and promoting the functioning of the organization. By applying organizational citizenship behavior to an online context, we propose online citizenship behavior, an individual's pro-social behavior in an online context. An individual's pro-social behavior, i.e., online citizenship behavior, could be considered as a way for the better management of online community and society. It also needs to examine the development of online citizenship behavior. This study examined online citizenship behavior from the friendship desire. Because online society or community is characterized by online relationships between members, the friendship between members would lead to pro-social behavior, i.e., helping others and promoting the functioning of the online society, in such online context. This study further examines the antecedents of friendship desire in terms of SNS interactivity with its four factors. The findings based on the survey from real SNS users explain that the three factors of SNS interactivity (connectivity, enjoyment, and synchronicity) increases online friendship desire which then increases online citizenship behavior significantly. This study contributes to the literature by examining the key role of online friendship desire in leading to online citizenship behavior and identifying its antecedents in terms of SNS characteristics. The findings in this study also provide guidance on how to manage online society and how to promote the effective functioning of SNS.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.204-212
• /
• 2016

This study was conducted to develop an edible smoked egg by penetrating seasoning through pressurization without damaging the eggshell and to investigate the quality characteristics of the product. The lyophilized smoked egg consisted of 2.43% moisture, 4.11% crude ash, 46.08% crude protein, 40.85% crude fat and 6.53% hydrated carbon. The total content of polyphenol was 3.11 mg%, 35.70% saturated fatty acid and 64.30% unsaturated fatty acid. Major types of saturated fatty acids included palmitic acid (C16:0), stearic acid (C18:0) and lauric acid (C12:0), while major unsaturated fatty acids included oleic acid (C18:1) and linoleic acid (C18:2). Due to smoking of the egg, the eggshell is dark brown, the egg albumen, egg yolk and egg shell are darker than boiled eggs, and the value of a (redness) is higher than that of boiled eggs. Overall, smoked eggs were organically superior than boiled eggs because of their seasoning and smoke flavor. The results of this study are expected to further the development of processed foods using domestic eggs and improve the egg processing industry.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.4
• /
• pp.169-177
• /
• 2018

Glass fiber reinforced polyester (GFRP) composites are widely used as structural materials in harsh environment such as underground pipes, tanks and boat hulls, which requires long-term water resistance. Especially, these materials might be damaged due to delamination between gelcoat and composites through an osmotic process when they are immersed in water. In this study, GFRP laminates were prepared by surface treatment of UPE (unsaturated polyester) gelcoat by vacuum infusion process to improve the durability of composite materials used in underground pipes. The composite surface coated with gelcoat was examined for surface defects, cracking, and hardness change characteristics in water-immersion environments (different temperatures of $60^{\circ}C$, $75^{\circ}C$, and $85^{\circ}C$). The penetration depth of cracks was investigated by micro CT imaging according to water immersion temperature. It was confirmed that cracks developed into the composites material at $75^{\circ}C$ and $85^{\circ}C$ causing loss of durability of the materials. The point at which the initial crack initiated was defined as the failure time and the life expectancy at $23^{\circ}C$ was measured using the Arrhenius equation. The results from this study is expected to be applied to reliability evaluation of various industrial fields where gelcoat is applied such as civil engineering, construction, and marine industry.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.603-615
• /
• 2020

The design factors of artificial recharge are determined by considering the hydrogeological characteristics of the aquifer. The optimal design factors for artificial recharge were derived after performing the injection tests step by step for each injection type (vertical well, ditch and mixed type), which were built in the test site of the study area. It was analyzed that the difference in the injection effect according to the diameter of the injection well was not large, and the 100 mm well was evaluated as appropriate in consideration of the availability and economy of land use. Since the injection effect was well maintained even in the upper rock, the depth of the injection well was proposed for the alluvial layer and the upper rock layer. On the other hand, in four cases of filter media in the ditch, it was analyzed that the penetration efficiency and the hydraulic interference effect indicated excellent injection performance when a filter medium of 10 to 30 mm diameter was filled in the ditch. In addition, the proper spacing of the injection wells was analyzed as 9~12 m considering the interference efficiency. The interference efficiency attenuation coefficient per 1 m of hole spacing was calculated to be 1.75% in this area. In the future study, the artificial recharge design factors obtained in this stage are applied and verified on site construction and operation. Also it is expected to contribute to securing water in areas where there is always a lack of water.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.2
• /
• pp.25-36
• /
• 2022

In this study, seepage control effect of relief well was evaluated quantitatively on embankment of small fill dam and levee. Seepage analysis of dam and levee were carried out according to the permeability of fill material and foundation and to analyze behaviour characteristics of seepage. The up-lift pressure at toe of embankment was analyzed which is generated by seepage according to relief well installation condition. The relief well could reduce pore water pressure which is to cause piping or up-lift pressure at foundation ground of embankment and it does not be influenced on geometric condition such as dam height and slope incline. In case of relative low permeable ground, the pore water pressure reduction effect of relief well was decreased compare with high permeable ground but it shows pore water pressure reduction effect compare with no relief well condition. The reduction effect of relief well shows relative gap according to diameter and penetration length of relief well and the installation length of relief well is the most effective factor for seepage control.

• Journal of Internet of Things and Convergence
• /
• v.8 no.2
• /
• pp.35-40
• /
• 2022

In the agricultural environment, pesticide control requires a high risk of work and a high labor force for farmers. The effectiveness of pesticide control using unmanned aerial vehicles varies according to climate, land type, and characteristics of unmanned aerial vehicles. Therefore, an effective method for pesticide control by unmanned aerial vehicles considering the spraying conditions and environmental conditions is required. In this paper, we propose an efficient pesticide control system based on agricultural unmanned aerial vehicles considering the application conditions and environmental information for each crop. The effectiveness of the proposed model was demonstrated by measuring the drop uniformity of pesticides according to the change in altitude and speed after attaching the sensory paper and measuring the penetration rate of the drug inside the canopy according to the change in crop growth conditions. Experiment result, the closer the height of the UAV is to the ground, the more evenly the crops are sprayed, but for safety reasons, 2m more is suitable, and on average a speed of 2m/s is most suitable for control. The proposed control system is expected to help develop intelligent services based on the use of various unmanned aerial vehicles in agricultural environments.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.128-133
• /
• 2002

This study was conducted to investigate the influence of storage time on the sapstain development of Japanese red pine and Korean pine logs during storage in log yard, and their stain characteristics. Japanese red pine and Korean pine trees were harvested and cut into logs in mid January of 2001. These logs were transported to the two local sawmills where they were closely stacked in remote parts of log yard. The logs were then sampled destructively by cutting seven to nine 3-cm long discs along the length of each log at intervals of 3, 4, 5, 6, and 8 month after felling. The stain coverage and maximal radial penetration of stain were measured from the discs of the sampled logs after the isolation of causal staining fungi. The sapstain was primarily infested by the attack of bark beetles and the species of bark beetle was identified as Tomicus piniperda. The main fungal species isolated from stained wood was Ophiostoma species. Based on the present study, the logs could be stored in log yard until May without stain; but stain development was rapid after May and the severity of stain increased proportionally with storage time. Korean pine was more susceptible to fungal stain than Japanese red pine. During summer storage, decay started to develop in logs and the main species were identified as Tyromyces sp. and Schizophyllum commune. Information provided in this paper would be very useful to develop more effective control strategies for sapstain prevention in Japanese red pine and Korean pine logs.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.4
• /
• pp.450-456
• /
• 2022

In this study, as the preliminary research on the development of heating concrete members, compressive strength and accelerated chloride diffusion behavior in the mortar specimens containing C₁₂A₇ based binder and anhydrite was evaluated. Also, the effect of the mixing ratio of the citric acid based retarder was quantitatively evaluated by considering 4 levels of mixing cases. The compressive strength tests of the mortar specimen were performed referred to KS L ISO 679, and the accelerated chloride diffusion tests were performed according to NT BUILD 492 and ASTM C 1202. In the mortar with 0.3 % of retarder, the highest compressive strength was evaluated, which showed the strength development ratio of 127.6 % compared to the control case. It was considered that engineering performance was improved by effectively securing setting and curing time with 0.3 % of citric acid based retarder. As the result of the evaluation of the passed charge and the accelerated chloride diffusion coefficient, the evaluation results had similar behavior with the results of compressive strength. According to the previous study, the strength behavior and the chloride diffusion behavior had a linear relationship. The mixture showing the highest strength performance had the highest durability performance for chloride ingress, and the heating concrete development from this study will be performed in the future.