• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.146-151
• /
• 2005

Electromagnetic penetration into an annular aperture in a thick conducting plane is investigated with the integral transform and eigen-function expansion method. The solution is analytic and is represented in rapidly-convergent series which is amenable to numerical analysis. Numerical computations shows that apertures with narrow annular gap have sharp transmit power peaks in frequency response.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.567-570
• /
• 2005

This study aims to verify the relationship between the penetration depth and chemical resistance, which can demonstrates the performance of the applied surface penetration sealers.

• The Journal of Engineering Geology
• /
• v.31 no.3
• /
• pp.433-445
• /
• 2021

Plasma blasting by high voltage arc discharge were performed in laboratory-scale soil samples to investigate the fluid penetration efficiency. A plasma blasting device with a large-capacity capacitor and columnar soil samples with a diameter of 80 cm and a height of 60 cm were prepared. Columnar soil samples consist of seven A-samples mixed with sand and silt by ratio of 7:3 and three B-samples by ratio of 9:1. When fluid was injected into A-sample by pressure without plasma blasting, fluid penetrated into soil only near around the borehole, and penetration area ratio was less than 5%. Fluid was injected by plasma blasting with three different discharge energies of 1 kJ, 4 kJ and 9 kJ. When plasma blasting was performed once in the A-samples, penetration area ratios of the fluid were 16-25%. Penetration area ratios were 30-48% when blastings were executed five times consecutively. The largest penetration area by plasma blasting was 9.6 times larger than that by fluid injection by pressure. This indicates that the higher discharge energy of plasma blasting and the more numbers of blasting are, the larger are fluid penetration areas. When five consecutive plasma blasting were carried out in B-sample, fluid penetration area ratios were 33-59%. Penetration areas into B-samples were 1.1-1.4 times larger than those in A-samples when test conditions were the same, indicating that the higher permeability of soil is, the larger is fluid penetration area. The fluid penetration radius was calculated to figure out fluid penetration volume. When the fluid was injected by pressure, the penetration radius was 9 cm. Whereas, the penetration radius was 27-30 cm when blasting were performed 5 times with energy of 9 kJ. The radius increased up to 333% by plasma blasting. All these results indicate that cleaning agent penetrates further and remediation efficiency of contaminated soil will be improved if plasma blasting technology is applied to in situ cleaning of contaminated soil with low permeability.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.2
• /
• pp.16-21
• /
• 2014

Characteristics of coating color penetration into paper were elucidated using various types of pulps and pigments. A commercial paper, KP and TMP handsheets were used for base paper. Clay and GCC were used as coating pigment. Laboratory rod draw down coater was used for coating application. Coating color penetration was evaluated by measuring the roughness of surface and back side of a coating layer. The results of coating roughness showed that clay was much better than GCC as a coating pigment. In case of pulp type, KP base paper was more effective than TMP base paper to reduce coating penetration.

• Journal of the Korean Ceramic Society
• /
• v.17 no.4
• /
• pp.188-196
• /
• 1980

To investigate the corrosion behavior of the clay-bonded kaolin chamotte by molten aluminum, the mixture of 20 wt% fire clay and 80 wt% kaolin chamotte was prepared and fired in the temperature range 900~120$0^{\circ}C$. The specimens fired at each temperature were reacted with molten aluminum at 90$0^{\circ}C$. The results obtained in this experiment are as followed. 1) It was confirmed through X-ray diffraction analysis that the clay-bonded kaolin chamotte exposed to molten aluminum suffered penetration by the reaction of aluminum with silica forming alumina and metallic silicon. 2) Penetration was independent whether the silica existed as free or one component of mullite. 3) Penetration of the specimen fired at 90$0^{\circ}C$ was negligible while the others fired above 100$0^{\circ}C$ showed remarkable penetration. 4) Penetration rate at 90$0^{\circ}C$ was parabolically increased with the holding time as in the case of metal oxidation.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.70-75
• /
• 1999

Adaptive control in the robotic GMA(Gas Metal Arc) welding is employed to monitor the information about weld characteristics and process paramters as well as modification of those parameters to hold weld quality within the acceptable limits. Typical characteristics are the bead geometry composition micrrostructure appearance and process parameters which govern the quality of the final weld. The main objectives of this paper are to realize the mapping characteristicso f penetration through the learning. After learning the neural network can predict the pene-traition desired from the learning mapping characteristic. The design parameters of the neural network estimator(the number of hidden layers and the number of nodes in a layer) were chosen from an error analysis. partial-penetration single-pass bead-on-plate welds were fabricated in 12mm mild steel plates in order to verify the performance of the neural network estimator. The experimental results show that the proposed neural network estimator can predict the penetration with reasonable accuracy and gurarantee the uniform weld quality.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2003.11a
• /
• pp.148-153
• /
• 2003

The influence of sizing, fiber and pigment type on coating penetration, using commercial paper and two types of handsheets as the base paper which were prepared from thermomechanical pulp(TMP) and hardwood bleached kraft pulp(KP) sized internally with alkyl ketone dimmer(AKD), was studied in terms of characteristics of coating holdout. Laboratory rod draw down coater was used for surface sizing and coating application. Characterization of coating penetration was done by measuring the roughness of the backside of coating layer. The backside of the coating was exposed by dissolving the fibers in a solution of cupriethylenedimine(CED). Data show that internal sizing of base paper is effective and surface sizing is more effective to prevent coating penetration. Comparing between the two types of base papers, backside roughness of coating layer of TMP sheet is much larger and sizing is more effective to reduce coating penetration than those of KP sheet. With regard to pigment type, clay is more effective than calcium carbonate for better coating holdout.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.1
• /
• pp.21-26
• /
• 2013

The influences of heat treatment and surface sizing on coating penetration were studied using two types of commercial base papers. Dry oven was used for heat treatment and laboratory rod draw down coater was used for surface sizing and coating application. Coating penetration was evaluated by measuring the roughness of the backside of coating layer. The backside of the coating was exposed by dissolving the fibers in a cupriethylenedimine(CED) solution. The results showed that both heat treatment and surface sizing were the effective methods to increase sizing degree and to reduce coating penetration.

• Journal of the Korea Furniture Society
• /
• v.18 no.4
• /
• pp.307-311
• /
• 2007

An experiment was conducted to know the essential oil penetration depth in radial and longitudinal direction of Prunus sargentii. Oil penetration depth was found greater than radial flow depth. Vessel conducted oil more than wood fiber. In radial direction, body ray parenchyma was found more permeable than marginal ray parenchyma and it was about 138% times higher. Furthermore penetration depth of oil in intercellular space was greater than ray parenchyma and it was about 250% higher than ray parenchymas. Initial flow speed was found high and then it gradually decreased.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.5
• /
• pp.566-573
• /
• 2015

The most important factor for the penetration performance of shaped charge is the liner design. By designing the liner to have properties of both high jet tip velocity and long jet break-up time, the better penetration performance could be acquired. Usually it is very difficult to satisfy above two conditions simultaneously. In this study, the liner with the shape of ogive was developed to have relatively larger jet mass compared to the conventional trumpet liner. The designed shaped charge showed jet properties with high jet tip velocity and long jet break-up time by using ogive liner and wave shaper. A commercially available hydro-dynamic code AUTODYN-2D was used for numerical analysis of jet formation. The flash X-ray test and the static penetration test were conducted to verify the results of numerical analysis.