• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.208-211
• /
• 2005

This paper presents an ultra-low partial discharge(PD) measurement system that has been accepted as a non-destructive method to estimate electrical insulation of low-voltage electric devices. The PD measurement system is composed of a coupling network, a low noise amplifier, and associated electronics. A shielding box is used to make a better condition against electromagnetic interference. A low cut-off frequency of the coupling network was 1MHz(-3 dB). Calibration tests on laboratory set-up have shown that the PD measurement system has a stable sensitivity of 11.4mV/pC. In an application experiment on a low-voltage induction motor(5HP), we could detect 0.77pC level of partial discharge pulse at the applied voltage of AC 664 V$_{peak}$.

• Journal of Korean Port Research
• /
• v.14 no.4
• /
• pp.475-479
• /
• 2000

A possibility of the implementation of a quartz crystal sensor to the determination of chemical oxygen demand is examined by checking the electrochemical behavior of the sensor in a glucose solution. Since the surface of a quartz crystal has to be oxidized, a relatively active metal is coated on the surface of a usual 9 MHz AT-cut crystal. The electrochemical behavior is investigated by measuring the changes of current, resonant frequency and resonant resistance while a constant potential is applied. The crystal is installed in a specially designed container, and a quartz crystal analyzer is utilized to measure the frequency and resistance simultaneously. The variations of the measurements are examined at different concentrations of glucose solution, and a proper relation between the concentrations of glucose solution, and a proper relation between the concentration and the measurements is analyzed. As a result, it is found that a linear relation between the concentration of less than 900 ppm and the peak current when a constant potential of -180 mV (SSCE) is applied. The relation can be utilized for the determination of glucose concentration in sea water, and considering a direct relation between gluose concentration and chemical oxygen demand tells a possibility of the measurement of chemical oxygen demand using quartz crystal oscillators.

• Journal of Korean Society on Water Environment
• /
• v.27 no.5
• /
• pp.654-660
• /
• 2011

One of the best way to control Combined Sewer Overflow (CSO) is proposed to construct first flush storage tank. But there is little known parameters for optimum design of these facilities. This study was conducted to get optimum design parameters for a first flush storage tank construction. The optimization of the tank is generally based upon some measure of SS(Suspended Solid) mass holding efficiency. Water quality deterioration of receiving water body happened right after first time occurring rainfall in dry weather seasons. So, design rainfall intensity is used at 2 mm/hr for peak of monthly average intensities of dry seasons. The capacities for each evaluated catchment are designed from 14.4 min to 16.1 min HRT of CSOs flow at design rainfall intensity. Owing to all storage tanks are connected to interception sewer having a redundancy, the suggested volume could be cut down.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.2
• /
• pp.229-235
• /
• 2004

Soy protein was hydrolyzed by 5 different pretenses and determinated antimicrobial activity of each hydrolysate. The soy protein hydrolysate treated by pretense from Aspergillus saitoi showed the highest antimicrobial activity among the protease studied and was used for further analysis. Soy protein hydrolysate was fractionated by ultrafiltration for M.W. 10,000,3,000 and 1,000. The M.W 1,000∼3,000 showed the highest antimicrobial activity. The minimum inhibition concentrations of obtained fraction were 0.5∼0.8 mg/mL for gram positive and negative microbials, and its activity was even observed after heating at 121$^{\circ}C$ for 10 min, suggesting that hydrolyzed protein having antimicrobial activity is quite heat-stable. Reverse-phase HPLC was further applied to separate the fraction and 8 peaks were found. Each 8 peaks were separated and pooled and measured antimicrobial activity. Among them, retention time of peak at 16.02 min showed the prominent antimicrobial activity.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.5
• /
• pp.41-50
• /
• 2014

This study evaluated the bonding property of fiber and flexural behavior of fiber reinforced concrete. Amorphous steel fiber, hooked steel fiber and polyamide fiber was used for evaluation of bonding property and flexural behavior. As a result, the hooked steel fiber was pulled out from matrix when peak stress. However amorphous steel fiber occurred shear failure because bonding strength between fiber and matrix was higher than tensile strength of fiber. Polyamide fibers occurred significantly displacement to peak stress because of elongation of fiber. After that peak stress, fiber was cut off. Amorphous steel fiber reinforced concrete had a greater maximum flexural load compared with hooked steel fiber reinforced concrete because bonding performance between fiber and matrix was high and mixed population of fiber was many. However flexural stress was rapidly reduced in load-deflection curve because of shear failure of fiber. Flexural stress of hooked steel fiber reinforced concrete was slowly reduced because fiber was pulled out from the matrix. In the case of polyamide fiber reinforced concrete, flexural stress was rapidly lowered because of elongation of fiber. However flexural stress was increased again because of bonding property between polyamide fiber and matrix. The pull-out properties of the fiber and matrix has effect on the deformation capacity and flexural strength of fiber reinforced concrete.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.4
• /
• pp.329-336
• /
• 2008

Efficient traffic network is required in urban area for good living condition. However, dense traffic network creates traffic jam and gives bad influences to the ground environment. Therefore, advanced use of underground and tunnel is required. But, in the last 20 years many tunnel fire accidents have occurred all over the world. Increase of tunnels and increase of traffics result in increase of tunnel fire. Tunnel fire creates damage to people and to the tunnel structure. Also, tunnel fire creates a big economical loss. In a mountain tunnel, the stability of the tunnel will not be disturbed by fire although the tunnel lining will get a severe damage. However, in a shield tunnel or immersed tube tunnel, cut and cover tunnel, there is a high possibility that tunnel itself will collapse by fire because their tunnel concrete lining is designed as a structural member. The aim of this experimental research is to verify the fire protection performance of newly developed cementitious material compared with the broadly used existing products in Europe and Japan. For the experiments, the general NATM tunnel concrete linings with the newly developed material were tested using fire loading curve of RABT (Maximum peak temperature is $1,200^{\circ}C$) and RWS (Maximum peak temperature is $1,350^{\circ}C$). From the test results, the newly developed fire protection material applied with 30 mm thickness showed good fire-proofing performance under RABT fire loading.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.2
• /
• pp.217-226
• /
• 2007

Putting score counts about 43 % of the golf score. The dominant idea of the putting motion to amateur golfers as well as to many professional golfers is a pendulum-like motion. If a golfer's putting stroke motion is a pendulum-like motion, the putting motion should be straight-back-and-through, the same backswing, downswing, and follow through length and period, and a swing with a fixed hinge joint. If the putting motions of the human are different from the pendulum motion, there could be confusion in understanding and teaching golf putting. The purpose of this study was to examine the center of rotation(COR) of the putter head to reveal whether professional golfers really putt like a pendulum. Thirteen male professional golfers were recruited for the study. Each golfers executed 10.94 m putts six times on an artificial grass mat. Putter head position data were collected through a 60 Hz three-dimensional motion analysis system and low pass filtered with cut-off frequency of 6 Hz. COR of the putter head was mathematically acquired. Each golfer's last five putting motions were considered. The results show that the COR of the putter head was neither fixed nor located inside of the golfer. The medio-lateral directional component of the COR of the putter head fluctuated in the range of 10 cm during downswing and follow through. The anterior-posterior directional component of the COR of the putter head was fixed from the beginning of the downswing through impact. Just after impact, however, it moved to the target up to 60 cm. The superior-inferior directional component of COR of the putter head moved in a superior direction with the beginning of the downswing and showed peak height just prior to impact. During the follow through, it moved back in an inferior direction. The height-normalized peak value of the COR of the putter head was $1.4{\pm}0.3$ height. Technically speaking, male professional golfers' 10.94 m putting motion is not a pendulum-like motion. The dominating idea of a pendulum-like motion in putting might come from the image of the flawless, smooth motion of a pendulum.

• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.77-82
• /
• 2000

A surface of polytetrafluoroethylene(PTFE) was modified with changing ion doses by 1 keV $Ar^+$ ion irradiation and Cu films having thickness $5000\;{\AA}$ were deposited on the modified PTFE. The SEM study showed that the surface texture of modified PTFE was in the form of cones whose height increased depending on ion doses. Through XPS spectra, it was found that the intensity of F ls peaks decreased with ion doses by preferential sputtering of F atoms and the C-C and / or C-F chains were formed by the crosslinking in the newly unstable chains. Cu films were deposited uniformly along the filaments formed on the modified PTFE. In x-ray diffraction (XRD) spectra of deposited Cu films on modified PTFE, a preferred orientation along (111) and (200) planes was found and the peak intensity of (111) plane increased as surface roughness of modified PTFE increased. The resistivity of Cu films was changed from $2.7{\mu}{\Omega}cm$ of unmodified PTFE to $4.3{\mu}{\Omega}cm$ of modified PTFE at ion dose of $1{\times}10^{16}/\textrm{cm}^2$ and the abrupt increase of resistivity in the modified PTFE at ion dose of $1{\times}10^{17}/\textrm{cm}^2$ was due to being cut off the film which resulted from the increased surface roughness.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.12 s.103
• /
• pp.1229-1238
• /
• 2005

OFDM(Orthogonal Frequency Division Multiplexing) communications system is very attractive for the high data rate wireless transmission. However, it may be distorted in the nonlinear HPA(High Power Amplifier) since OFDM signal has hish PAPR(Peak-to-Average Power Ratio). In this paper, a new method using control tone is studied for reducing the PAPR and we call it PCT(PAPR Control Tone) method. This proposed PCT method is to assign control tones for PAPR reduction at the predefined sub-carriers. After IFFT(Inverse Fast Fourier Transform) and PAPR calculation, the OFDM data signal of the lowest PAPR is selected to transmit. Unlike the conventional method, it can cut down the computational complexity because it does not require the transmission and demodulation process of side information about the phase rotation. Furthermore, if this method is made up in parallel configuration, it can solve the time delay problem so that it can be processed in real time processing. This proposed method is compared with the conventional selected mapping(SLM) technique. We find out the PAPR reduction performance and BER when the number of control tone is 6 and nonlinear HPA is considered.

• The Korean Journal of Nuclear Medicine
• /
• v.31 no.1
• /
• pp.83-89
• /
• 1997

About one-third of radiologically indeterminate solitary pulmonary nodules (SPN) are eventually turned out to be malignant. It is very important to noninvasively determine whether the SPN is malignant or not for the decision of its way of management. PET imaging is highlighted by its unique ability of imaging the function and metabolism of cells. Glucose metabolism is increased in malignant transformed cells. We peformed FDG-PET studies in patients who had radiologically indeterminate SPN and compared the findings with histologic diagnoses to assess the diagnostic accuracy in the detection of malignancy and to decide which parameter is the most suitable for clinical practice among peak SUV (pSUV), average SUV (aSUV), 50/10 ratio, and time-activity curve (TAC), Thirty patients were included in this study and the most useful parameter was pSUV. The sensitivity and specificity in the detection of malignant SPN using 3.5 as a cut off pSUV were both 87%. Interestingly, all 2 false-negative cases were bronch-ioloalveolar carcinoma on histologic examination. If these cases, which could be strongly suspected by CT findings, were excluded, the sensitivity of pSUV was 100%. In conclusion, PET imaging is very helpful for determining malignancy in indeterminate SPN and pSUV is a conveniently measurable parameter which is valuable for interpretation.