• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.9
• /
• pp.812-817
• /
• 2002

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.8
• /
• pp.766-771
• /
• 2005

In this study, PD(partial discharge) signals which occur at stator coil of traction Motor are acquired these data are used for classifying the PD sources. NN(neural network) has recently applied to classify the PD pattern. The PD data are used for the learning process to classify PD sources. The PD data come from normal specimen and defective specimens such as internal void discharges, slot discharges and surface discharges. PD distribution parameters are calculated from a set of the data, which is used to realize diagnostic algorithm. NN which applies distribution parameters is useful to classify the PD patterns of defective sources generating in stator coil of traction motor.

• Korean Journal of Environmental Biology
• /
• v.22 no.1
• /
• pp.89-92
• /
• 2004

The effects of different light quality on the change of membrane potential difference (PD) of the guard cell in the intact leaf have been investigated. The mombrane PD was about -5.5 mV by white light of 600 $\mu$moles $m^{-2}\; s^{-1}$. The mean PD of change caused by red light was about -5.2 mV at the light intensity of 80 $\mu$moles $m^{-2}\; s^{-1}$. Membrane PD of guard cells in response to blue light was saturated at low light intensity. However, red and green light enhanced the change of membrane PD of guard cells with increasing intensity. In green light the biggest change of memrane PD was around -4 mV, whereas, with blue light the change of of memrane PD was around -2 mV. Accordingly, the membrane PD of guard cell showed the different degree of hyper-polarization by each wavelength.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.152-155
• /
• 2002

During normal operation, partial discharge(PD) tests were performed using turbine generator analyzer(TGA) in high voltage motor. Epoxy-mica couplers are installed at motor terminal and analyzed PD signal using TGA. #A motor stator insulation is good because small partial discharges are detected PD pattern show that PD occurs in insulation. PD of #B motor is larger than that of #A motor and PD pattern show that positive PD larger than negative PD. It means that PD occurs between insulation and slot. And A phase PD magnitude of #B motor is large and high compare with any other phase. Therefore wedge, core and slot of #B motor need to check and repair.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.199-202
• /
• 2002

During normal operation, partial discharge(PD) tests were performed using turbine generator analyzer(TGA) in high voltage motor. Epoxy-mica couplers are installed at motor terminal and analyzed PD signal using TGA. #A motor stator insulation is good because small partial discharges are detected. PD pattern show that PD occurs in insulation. PD of #B motor is larger than that of #A motor and PD pattern show that positive PD larger than negative PD. It means that PD occurs between insulation and slot. And A phase PD magnitude of #B motor is large and high compare with any other phase. Therefore wedge, core and slot of #B motor need to check and repair.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.5
• /
• pp.177-181
• /
• 2003

Partial discharge pulse shapes from variable PD (partial discharge) sources sustain many characteristics such as types of PD. Ultra high frequency antennas have wide bandwidth from 30KHz to 2㎓. Therefore, signals taken from a UHF antenna have important attributes (rising time, falling time, shape factor, etc.) for electromagnetic sources, such as PD sources. We investigated PD pulse shapes from several PD sources using a UHF antenna and the results were used for classification of PD sources. Features for discrimination are extracted from frequency distribution and LPC (Linear Prediction Coefficient) of time signal. RBFN are used for investigating the possibility of classification of multi-PD sources.

• Electrical & Electronic Materials
• /
• v.11 no.11
• /
• pp.1-8
• /
• 1998

This paper presents an arificial neuro-fuzzy technique based prtial discharge (PD) pattern classifier to power system application. This may require a complicated analysis method employ -ing an experts system due to very complex progressing discharge form under exter-nal stress. After referring briefly to the developments of artificical neural network based PD measurements, the paper outlines how the introduction of new emerging technology has resulted in the design of a number of PD diagnostic systems for practical applicaton of residual lifetime prediction. The appropriate PD data base structure and selection of learning data size of PD pattern based on fractal dimentsional and 3-D PD-normalization, extraction of relevant characteristic fea-ture of PD recognition are discussed. Some practical aspects encountered with unknown stress in the neuro-fuzzy techniques based real time PD recognition are also addressed.

• Polymer(Korea)
• /
• v.33 no.6
• /
• pp.615-619
• /
• 2009

Pd-POSS nanoparticles were produced from the reaction of palladium (II) acetate and octa(3-aminopropyl)octasilsesquioxane octahydrochloride (POSS-${NH_3}^+$) in methanol at room temperature. Pd-POSS nanoparticles with a mean diameter of 60-80 nm were the highly ordered spherical aggregates. In contrast, Pd nanoparticles with a size of 4.0 nm were obtained when POSS-${NH_3}^+$ was not introduced. Pd-POSS/PAA nanocomposites of Pd-POSS nanoparticles and poly(acrylic acid) (PAA) were fabricated by utilizing ionic interactions between positively charged Pd-POSS nanoparticles and negatively charged carboxylate groups of PAA. PAA was used as a cross-linker for the preparation of hybrid nanocomposites with the controlled organized structures of Pd-POSS nanoparticles. That is, the self-organization of Pd-POSS nanoparticles was formed into the shape of continuous lines by using PAA as a cross-linker. The composition, structure, surface morphology, and thermal stability of the Pd-POSS/PAA nanocomposites were studied by FE-SEM, AFM, TEM, FT-IR, and TGA.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.5
• /
• pp.411-420
• /
• 2017

In this paper, two methods of making the Pd-added $SnO_2$ ($Pd-SnO_2$) powder with pure tetragonal phase by the hydrazine method were suggested and compared in terms of crystal structure, surface morphology, and alcohol gas response. One of the addition methods is to use $PdCl_2$ as a Pd source, the other is to use Pd-based organic with oleylamine (OAM). When Pd concentration was increased from 0 to 5 wt%, the average grain size of $Pd-SnO_2$ made with Pd-OAM were decreased from 32 to 12 nm. In the case of using with $PdCl_2$, grain size of the $PdCl_2$ fell to less than 10 nm. However, agglomerated and extruded surface morphology was observed for the films with Pd addition over 4 wt%. The crack-free $Pd-SnO_2$ thick films were able to successfully fill the $30{\mu}m$ gap of patterned Pt electrodes by optimized ink dropping method. Also, the 2 wt% $Pd-SnO_2$ thick film made with PdCl2 showed gas responses ($R_{air}/R_{gas}$) of 3.7, 5.7 and 9.0 at alcohol concentrations of 10, 50 and 100 ppm, respectively. On the other hand, the prepared 3 wt% $Pd-SnO_2$ thick film with Pd-OAM exhibited very excellent responses of 3.4, 6.8 and 12.2 at the equivalent measurement conditions, respectively. The 3 wt% $Pd-SnO_2$ thick film with Pd-OAM has a specific surface area of $31.39m^2/g$.

• Journal of the Korean Vacuum Society
• /
• v.12 no.4
• /
• pp.218-227
• /
• 2003

Pd/Si/Ti/Pt and Pd/Si/Pd/Ti/Au ohmic contacts to n-type InCaAs were investigated for applications to AlGaAs/GaAs HBT emitter ohmic contacts. In the Pd/Si/Ti/Pt ohmic contact, as-deposited contact showed non-ohmic behavior, and high specific contact resistivity of $5\times10^{-3}\Omega\textrm{cm}^2$ was achieved by rapid thermal annealing at $375^{\circ}C$/10 sec. However, the specific contact resistivity decreased remarkably to $2\times10^{-6}\Omega\textrm{cm}^2$ by annealing at $425^{\circ}C$/10sec. In the Pd/Si/Pd/Ti/Au ohmic contact, minimum specific contact resistivity of $3.9\times10^{-7}\Omega\textrm{cm}^2$ was achieved by annealing at $400^{\circ}C$/20sec. In both ohmic contacts, low contact resistivity and non-spiking planar interface between ohmic materials and InGaAs were maintained. Therefore, these thermally stable ohmic contact systems are promising candidates for compound semiconductor devices. RF performance of the AlGaAs/GaAs HBT was also examined by employing the Pd/Si/Ti/Pt and Pd/Si/Pd/Ti/Au systems as emitter ohmic contacts. Cutoff frequencies were 63.9 ㎓ and 74.4 ㎓, respectively, and maximum oscillation frequencies were 50.1 ㎓ and 52.5 ㎓, respectively. It shows very successful high frequency operations.