• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.4
• /
• pp.331-341
• /
• 2016

To evaluate the physicochemical and radiological properties of raw materials and by-products in domestic distribution, about 220 samples with 16 species were prepared. We measured the energy spectrum and the chemical content, such as U, Th, and K, using a $LaBr_3$ scintillation detector and ED-XRF. In addition, HPGe detector was used to analyze the radioac-tivity of $^{234}Th$, $^{234}mPa$, and $^{214}Bi$ in uranium decay series and $^{228}Ac$, $^{212}Pb$, and $^{208}Tl$ in thorium decay series, and $^{40}K$. The correlation between characteristic variables, such as the count rate in several ROIs, chemical content, and radioactivity, was assessed to infer the radioactivity of natural radionuclides through a rapid screening method. Based on the results, a characteristic database for raw material and by-product in domestic distribution was established and it will provide useful information in the analysis procedure and improve the accuracy and reproducibility in the analysis of natural radionuclides.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.12 no.2
• /
• pp.97-105
• /
• 2014

In the case of the direct measurement of $^{226}Ra$ using a HPGe gamma-ray spectrometer, the interference between gammarays with 186.21 keV of $^{226}Ra$ and 185.7 keV of $^{235}U$ should be corrected to calculate the net peak area in the energy spectrum. In general, it is very difficult to conduct peaks stripping with difference of about 0.5 keV, although a HPGe with the superior resolution is applied and the maximum channels is applied to the spectrometer. In this study, several interference correction techniques in the direct measurement were surveyed to evaluate the feasibility for the measurement of $^{226}Ra$ using the gamma-ray spectrometery. Applying the interference corrections to the analysis of raw materials and by-products, the method validation for the direct measurement of $^{226}Ra$ was conducted by evaluating the measurement uncertainty, linearity, and range. As a result, the optimum method of the interference correction was selected by comparing with the indirect measurement of which progenies of $^{226}Ra$, such as $^{214}Pb$ and $^{214}Bi$, were analyzed in the secular equilibrium state.

• Economic and Environmental Geology
• /
• v.25 no.3
• /
• pp.233-243
• /
• 1992

Ore mineralization of the Hwanghak copper deposit in the Ogsan area occurred in three stages of quartz (stage I and II) and calcite (stage III) veining along fissures in Early Cretaceous sedimentary rocks. Ore minerals are pyrite, pyrrhotite, chalcopyrite (dominant), sphalerite, hematite, galena, and Ag-, Pb-, and Bi-sulfosalts. These were deposited during the first stage at temperatures between $370^{\circ}C$ and < $200^{\circ}C$ from fluids with salinities between 0.5 and 7.6 equiv. wt. % NaCl. There is evidence of boiling and this suggests pressures of less than 180 bars during the first stage. Equilibrium thermodynamic interpretation accompanying with mineral paragenesis and fluid inclusion data indicates that copper precipitation in the hydrothermal system occurred due to cooling and changing in chemical conditions ($fs_2$, $fo_2$, pH). Gradual temperature decrease from $350^{\circ}$ to $250^{\circ}C$ of ore fluids by boiling and mixing with less-evolved meteoric waters mainly led to copper deposition through destabilization of copper chloride complexes. Sulfur isotope values of sulfide minerals decrease systematically with paragenetic time from calculated ${\delta}^{34}S_{H_2S}$ values of 8.2 to 4.7‰. These values, together with the observed change from sulfide-only to sulfide-hematite assemblages and fluid inclusion data, suggest progressively more oxidizing conditions, with a corresponding increase of the $sulfate/H_2S$ ratio of hydrothermal fluids. Measured and calculated hydrogen and oxygen isotope valutls of ore-forming fluids suggest meteoric water dominance, approaching unexchanged meteoric water values.

• Economic and Environmental Geology
• /
• v.46 no.2
• /
• pp.199-206
• /
• 2013

The Daehyun gold-silver deposit consists of two hydrothermal quartz veins that fill NE-trending fractures in the Cambro-Ordovician calcitic marble. I have sampled wallrock, hydrothermaly-altered rock and gold-silver ore vein to study the element dispersion and element gain/loss during wallrock alteration. The hydrothermal alteration doesn't remarkably recognized at this deposit and consists of mainly calcite, dolomite, quartz and minor epidote. The ore minerals composed of arsenopyrite, pyrrhotite, pyrite, sphalerite, stannite, chalcopyrite, galena, electrum, native bismuth and silver-bearing mineral. Based on analyzed data, the chemical composition of wallrock consists of mainly $SiO_2$, CaO, $CO_2$ with amounts of $Al_2O_3$, $Fe_2O_3(T)$ and MgO. The contents of $SiO_2$, $Fe_2O_3(T)$, MgO, CaO and $CO_2$ vary significantly with distance from ore vein. The element dispersion doesn't remarkably recognized during wallrock alteration and only occurs near the ore vein margin because of physical and chemical properties of wallrock. Remarkable gain elements during wallrock alteration are $Fe_2O_3(T)$, total S, Ag, As, Bi, Cd, Cu, Ni, Pb, Sb, Sn, W and Zn. Remarkable loss elements are $SiO_2$, MnO, MgO, CaO. $CO_2$ and Sr. Therefore, Our result may be used when geochemical exploration carry out at deposits hosted calcitic marble in the Hwanggangri metallogenic district.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.35 no.1
• /
• pp.27-32
• /
• 2009

Human hair is an excretory system for trace metals and thus metal content in human hair can reflect the body status. The investigation of trace elements in human hair has been correlated with the diagnosis of various diseases as well as the monitoring of deficiency statues in nutrition. Many chronic diseases may be related to mineral status, some may be related to toxic mineral. Hair samples were collected from 120 inhabitants of the city of Seoul, Korea. In this study the concentrations of 10 elements (Hg, Pb, Cd, Al, As, U, Bi, Sb, Ba, Be) in hair were determined by inductively coupled plasma mass spectroscopy (ICP-MS). The conclusions showed that people in Seoul, Korea were affected by some kinds of toxic minerals. The Hg concentrations of male are higher than those of female and reference range. The mean concentration of Sb was higher in the female than male and reference range. In age distribution, the mean concentration of Hg was in 40's are higher than 20's and 30's and reference range. The concentrations of Al were the highest in the 20's. After analyzing, we concluded that a compounded treatment should be conducted, which considers the variety of factors related to detoxification.

• Korean Journal of Optics and Photonics
• /
• v.9 no.4
• /
• pp.221-226
• /
• 1998

Ternary heavy metal oxide glasses in the $PbO-Bi_2O_3-Ga_2O_3$ system doped with $Er_2O_3$ were prepared and their spectroscopic properties, such as radiative transition probability, calculated and measured radiative lifetimes and cross-sections of 1.5 $\mu\textrm{m}$ and 2.7 $\mu\textrm{m}$ emissions were analyzed. Enhanced quantum efficiencies of some electronic transitions were evident mainly because of the low vibrational phonon energy ($~500cm^{-1}$) inherent in the host glasses. This seems to be the main reason for obtaining the 2.7 $\mu\textrm{m}$ luminescence which is normally quenched in the conventional oxide glasses. In addition, green and red fluorescence emissions were observed through the frequency upconversion processes of the 798 nm excitation. Non-radiative transition due to the multiphonon relaxation is a dominant lifetime-shortening mechanism in the 4f-4f transitions in $Er^{3+}$ ion except for the $^4S_{3/2}{\rightarrow}^4I_{15/2}$ transition where a non-radiative transfer to band-gap excitation of the host glasses is dominant. Melting of glasses under an inert gas atmosphere and (or) addition of the typical glass-network former into glasses is necessary in order to enhance the quantum efficiency of the transition.

• Journal of Radiation Protection and Research
• /
• v.46 no.3
• /
• pp.127-133
• /
• 2021

Background: Phosphogypsum is material produced as a byproduct in fertilizer industry and is generally used for building materials. This material may contain enhanced radium-226 (²²⁶Ra) activity concentration compared to its natural concentration that may lead to indoor radon accumulation. Therefore, an accurate measurement method is proposed in this study to determine ²²⁶Ra activity concentration in phosphogypsum sample, considering the potential radon leakage from the sample container. Materials and Methods: The International Atomic Energy Agency (IAEA) phosphogypsum reference material was used as a sample in this study. High-purity germanium (HPGe) gamma spectrometry was used to measure the activity concentration of the ²²⁶Ra decay products, i.e., ²¹⁴Bi and ²¹⁴Pb. Marinelli beakers sealed with three different sealing methods were used as sample containers. Due to the potential leakage of radon from the Marinelli beaker (MB), correction to the activity concentration resulted in gamma spectrometry is needed. Therefore, the leaked fraction of radon escaped from the sample container was calculated and added to the gamma spectrometry measured values. Results and Discussion: Total activity concentration of ²²⁶Ra was determined by summing up the activity concentration from gamma spectrometry measurement and calculated concentration from radon leakage correction method. The results obtained from ²¹⁴Bi peak were 723.4 ± 4.0 Bq·kg^-1 in MB1 and 719.2 ± 3.5 Bq·kg^-1 in MB2 that showed about 5% discrepancy compared to the certified activity. Besides, results obtained from ²¹⁴Pb peak were 741.9 ± 3.6 Bq·kg^-1 in MB1 and 740.1 ± 3.4 Bq·kg^-1 in MB2 that showed about 2% difference compared to the certified activity measurement of ²²⁶Ra concentration activity. Conclusion: The results show that radon leakage correction was calculated with insignificant discrepancy to the certified values and provided improvement to the gamma spectrometry. Therefore, measuring ²²⁶Ra activity concentration in TENORM (technologically enhanced naturally occurring radioactive material) sample using radon leakage correction can be concluded as a convenient and accurate method that can be easily conducted with simple calculation.

• Analytical Science and Technology
• /
• v.20 no.3
• /
• pp.219-226
• /
• 2007

Glass is frequently encountered as types of materials that are submitted to forensic science laboratories as a result of trace evidence transfers. The repeatability and the reproducibility of trace element analysis were presented. An analysis of variance (ANOVA) was performed on laser ablation inductively coupled plasma spectrometric analyses of the fragments to identify the source. Pairwise comparisons were completed for all samples. In a pairwise comparison, each sample was compared to each other for a possible [n(n-1)/2] (n : numbers of the samples) total comparison to associate/discriminate samples using Tukey's HSD method. The aim of this study was to determine the utility of LA-ICP-MS for multi-element analysis of forensic samples. The 12 glass fragments from two manufacturers were collected and analyzed to identify the source. An analysis of variance (ANOVA) was performed on 31 elements in NIST 612 Trace elements in Glass. Elements were classified into four categories defined by the combination of precision and variation of inter-samples. We selected 11 elements, 209Bi, 90Zr, 121Sb, 178Hf, 59Co, 238U, 208Pb, 140Ce, 118Sn, 49Ti and 137Ba. 6 pairs out of 66 possible pairs were not distinguished when compared by 137Ba (p<0.05). However, all samples were distinguished using both 49Ti and 137Ba (p<0.05). In conclusion, multi-elemental analysis with LA-ICP-MS is a potential tecnique for the discrimination of forensic samples.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.3
• /
• pp.19-27
• /
• 2003

Surface finishes of PCB laminates are important in the solder joint reliability of flip chip package because the types and thicknesses of intermetallic compound(IMC), and compositions and hardness of solders are affected by them. In this study, effects of surface finishes of PCB on the low cycle fatigue resistance of Sn-based lead-free solders; Sn-3.5Ag, Sn-3.5Ag-XCu(X=0.75, 1.5), Sn-3.5Ag-XBi(X=2.5, 7.5) and Sn-0.7Cu were investigated for the Cu and Au/Ni surface finish treatments. Displacement controlled room temperature lap shear fatigue tests showed that fatigue resistance of Sn-3.5Ag-XCu(X=0.75, 1.5), Sn-3.5Ag and Sn-0.7Cu alloys were more or less the same each other but much better than that of Bi containing alloys regardless of the surface finish layer used. In general, solder joints on the Au/Ni finish showed better fatigue resistance than those on the Cu finish. Cross-sectional fractography revealed microcracks nucleation inside of the interfacial IMC near the solder mask edge, more frequently on the Cu than the Au/Ni surface finish. Macro cracks followed the solder/IMC interface in the Bi containing alloys, while they propagated in the solder matrix in other alloys. It was ascribed to the Bi segregation at the solder/IMC interface and the solid solution hardening effect of Bi in the $\beta-Sn$ matrix.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.3 no.1
• /
• pp.17-21
• /
• 1974

Tasty constituents such as free amino acids. free organic acids and free sugars and minerals in clavariaceae botrytis were surveyed through the course of this study. The results were as, follows: 1. Isoleucine valine threonine alanine methionine cysteine glutamine histidine glutamic acid and aspartic acid were presented in clavariaceae botrytis, and aspartic acid showed the highest amount. 2. Succinic acid was the major organic acid in clavariaceae botrytis, and also citric acid malic acid and fumaric acid were presented. 3. Clavariaceae botrytis contained fructose, maltose glucose and sucrose ; glucose and sucrose were more than 80% of total sugars. 4. Na K Mg Ca Zn Mn Cu am Fe by atomic absorption spectrometer were detected and assayed. and Al Si Ni Sn Ti Cr Ag Pb B and Sr detected by emission spectrograph. K of these minerals showed the highest amount but very small amount of Ca was presented.