• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.1012-1016
• /
• 2004

In this paper, we propose a simple but optimized NC code generating technique for disk cams by means of tool path error control in a five-axis CNC machining center. Using the geometric theorem of the triangle made between manufacturing points and error checkpoint, the tool path error has been studied for disk cams profile generation and an improvement in the profile has been obtained. Then, based on the present manufacturing approach a computer program is developed on $C^{++}$ language to perform and to verify the shape design, the manufacturing simulation, and the optimized generation of the NC code.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2431-2433
• /
• 1999

Phase errors of arrayed waveguide degrade the performance of AWG router, especially for dense WDM system. So it is necessary to measure the phase error and to compensate. The analysis method of the interference signal from the low coherence interferometer to measure the path length difference phase error is studied. The interference signal generated assuming the intentional path length difference errors of 0.1$\sim$0.4${\mu}m$ are analyzed and the results show that the path length difference phase error of ${\Delta}L$ within ${\pm}14^{\circ}$ of sampling phase error can be accurately measured.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.58-58
• /
• 2001

This paper shows a practical approach that is robust to the errors causing path-delay in mobile wireless location, and analyzes its performance by comparing with other methods. NLOS(non-line-of-sight) error and multipath are two big sources of positioning error in wireless location. Contrary to GPS(global positioning system), they result from the terrestrial propagation of a signal. Especially, since LOS(line-of-sight) path between a transceiver and a receiver is blocked by intermediate buildings and topography, NLOS causes a signal to be reflected and diffracted. This path-delay error is very localized, and so, it is not easy to be estimated and mitigated. To treat such localized error, therefore ...

• 제어로봇시스템학회논문지
• /
• 제20권2호
• /
• pp.211-217
• /
• 2014

This paper addresses an algorithm of path planning for autonomous driving of a ground vehicle in waypoint navigation. The proposed algorithm is flexible in utilization under a large GPS positioning error and generates collision-free multiple paths while pursuing minimum traveling time. An optimal path reduces inefficient steering by minimizing lateral changes in generated waypoints along a path. Simulation results compare the proposed algorithm with the A* algorithm by manipulation of the steering wheel and traveling time, and show that the proposed algorithm realizes real-time obstacle avoidance by quick processing of path generation, and minimum time traveling by producing paths with small lateral changes while overcoming the very irregular positioning error from the GPS.

• 로봇학회논문지
• /
• 제16권3호
• /
• pp.250-259
• /
• 2021

Path planning is one of the important technologies for automated parking. It requires to plan a collision-free path considering the vehicle's kinematic constraints such as minimum turning radius or steering velocity. In a complex parking lot, Rapidly-exploring Random Tree^* (RRT^*) can be used for planning a parking path, and Reeds-Shepp or Hybrid Curvature can be applied as a tree-extension method to consider the vehicle's constraints. In this case, each of these methods may affect the computation time of planning the parking path, path-tracking error, and parking success rate. Therefore, in this study, we conduct comparative analysis of two tree-extension functions: Reeds-Shepp (RS) and Hybrid Curvature (HC), and show that HC is a more appropriate tree-extension function for parking path planning. The differences between the two functions are introduced, and their performances are compared by applying them with RRT^*. They are tested at various parking scenarios in simulation, and their advantages and disadvantages are discussed by computation time, cross-track error while tracking the path, parking success rate, and alignment error at the target parking spot. These results show that HC generates the parking path that an autonomous vehicle can track without collisions and HC allows the vehicle to park with lower alignment error than those of RS.

• 한국기계가공학회지
• /
• 제3권4호
• /
• pp.50-55
• /
• 2004

Because of the development in mold industries, the geometrical form accuracy of the milled surface is getting more and more important. It has been known that the geometrical form accuracy is affected by machine conditions, cutting conditions, tool conditions and tool path and so on. Among them, the tool approaching path causes the change in material removal per tooth at the end of each machining cycle. And, this change generates the geometrical form error around the region where the tool engages the workpiece initially. So, it is impossible to eliminate the geometrical error caused by the tool approaching path. Thus, characteristics of this geometrical error are studied analytically and experimentally to minimize this region.

• 소음진동
• /
• 제8권3호
• /
• pp.485-493
• /
• 1998

Many of the adaptive noise control systems utilize a form of the least mean square (LMS) algorithms. In the active control of noise, it is common practice to locate an error microphone far from the control source to avoid the near-field effects by evanescent waves. Such a distance between the control source and the error microphone makes a certain level of time-delay inevitable and, hence, may yield undesirable effects on the convergence properties of control algorithms such as filtered-x LMS. This paper discusses the dependence of the convergence rate on the acoustic error path in these popularalgorithms and introduces new algorithms which increase the convergence region regardless of the time-delay in the acoustic error path. Performances of the new LMS algorithms are presented in comparison with those by the conventional algorithms based on computer simulations and experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 B
• /
• pp.843-845
• /
• 1995

There are a variety of trajectory and control algorithms available for robot trajectory tracking. Before using the enhanced trajectory and control algorithms to reduce the tracking error, we introduce the new method which reduces the tracking error by clipping the joint velocity. A lot of robot trajectory tracking methods are proposed to enhance the robot tracking, but irregular tracking errors are always accompanied. Up to now, these irregular tracking errors are gradually but uniformly reduced by introducing more complicated control algorithms. It is intuitively obvious to reduce only the big errors selectively in the irregular ones for the better performance. By heuristic method, big tracking errors in these irregular ones are assumed mostly due to the fast moving of joint with respect to the same tracking and control method. So, in this paper, we introduce a new method which reduce the big tracking errors by clippings the joint velocity with the constraint of given path. Using this method, desired trajectory tracking is obtained within the far reduced error bound. Also, this method is successfully applied to generate the path-constrained error reducing trajectories for 2-axis SCARA type robot.

• 전기전자학회논문지
• /
• 제23권1호
• /
• pp.22-28
• /
• 2019

본 연구는 차량용 보링 생산 공정에서 기계적인 에러를 체크하기 위한 품질 체크용 모니터링 시스템을 개발한다. 기계적인 에러는 이상적인 절단경로와 비교하여 실제 절단경로의 공간위치 차이에서 나타난다. 제조공정 제품의 오차를 모니터하기 위해 제품의 인지왜곡, 죄임 에러, 기계공구의 회전과 운동에러의 반경회전과 같이 보링 품질에 영향을 미치는 다수 요소들을 설명한다. 생산품질을 입증하기 위해 IT 융합에 기반한 공정 에러율을 분석하고 분석 데이터를 메모리에 저장하는 품질체크 방법을 제안한다. 따라서 불량 생산 제품을 감지함으로써, 생산 코스트와 베어링의 손실을 줄일 수 있다.

• 대한기계학회논문집
• /
• 제14권6호
• /
• pp.1542-1551
• /
• 1990

본 연구에서는 직경오차를 최종 다듬질 가공 직전에 선반의 주축 정지 상태에 서 공구대에 부착시킨 전기마이크로미터로 측정하는 방법을 이용하여, 어떠한 공작물 형상에 대해서도 오차 측정경로를 NC 프로그램으로 자동 생성하고 이를 이용하여 직경 오차를 측정, 보정하는 알고리즘을 제안함과 동시에 수정된 최종 다듬질 가공용 NC프 로그램을 자동적으로 생성하는 시스템을 개발하고자 한다.