• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.2
• /
• pp.135-144
• /
• 2009

Fuzzy hybrid control technique with a smart tuned mass damper(STMD) was proposed in this study for the suppression of wind-induced motion of a tall building. To develop the effective control algorithm for a STMD, skyhook and groundhook control algorithms were employed. Usually, skyhook controller can effectively reduce STMD motion and groundhook controller shows good control performance for the reduction of building responses. In this study, fuzzy hybrid controller, which can determine an optimal weighting factor for combining two controllers in real time, was developed to improve the control performance of conventional hybrid controller using weighted sum approach. A 76-story office building was used as an example structure to investigate the performance of the proposed controller. A magnetorheological(MR) damper was used to develop a STMD and the control performance of STMD was evaluated comparing with the passive and active TMD. The numerical studies show that the control effectiveness of a STMD is significantly superior to that of the conventional TMD. It is also shown that fuzzy hybrid controller can effectively adjust skyhook and groundhook control algorithms and reduce both responses of STMD and building.

• Archives of Plastic Surgery
• /
• v.43 no.2
• /
• pp.134-144
• /
• 2016

In adults, mallet finger is a traumatic zone I lesion of the extensor tendon with either tendon rupture or bony avulsion at the base of the distal phalanx. High-energy mechanisms of injury generally occur in young men, whereas lower energy mechanisms are observed in elderly women. The mechanism of injury is an axial load applied to a straight digit tip, which is then followed by passive extreme distal interphalangeal joint (DIPJ) hyperextension or hyperflexion. Mallet finger is diagnosed clinically, but an X-ray should always be performed. Tubiana's classification takes into account the size of the bony articular fragment and DIPJ subluxation. We propose to stage subluxated fractures as stage III if the subluxation is reducible with a splint and as stage IV if not. Left untreated, mallet finger becomes chronic and leads to a swan-neck deformity and DIPJ osteoarthritis. The goal of treatment is to restore active DIPJ extension. The results of a six- to eight-week conservative course of treatment with a DIPJ splint in slight hyperextension for tendon lesions or straight for bony avulsions depends on patient compliance. Surgical treatments vary in terms of the approach, the reduction technique, and the means of fixation. The risks involved are stiffness, septic arthritis, and osteoarthritis. Given the lack of consensus regarding indications for treatment, we propose to treat all cases of mallet finger with a dorsal glued splint except for stage IV mallet finger, which we treat with extra-articular pinning.

• The Korean Journal of Physiology and Pharmacology
• /
• v.18 no.6
• /
• pp.503-508
• /
• 2014

Spontaneous myometrial contraction (SMC) in pregnant uterus is greatly related with gestational age and growing in frequency and amplitude toward the end of gestation to initiate labor. But, an accurate mechanism has not been elucidated. In human and rat uterus, all TRPCs except TRPC2 are expressed in pregnant myometrium and among them, TRPC4 are predominant throughout gestation, suggesting a possible role in regulation of SMC. Therefore, we investigated whether the TRP channel may be involved SMC evoked by mechanical stretch in pregnant myometrial strips of rat using isometric tension measurement and patch-clamp technique. In the present results, hypoosmotic cell swelling activated a potent outward rectifying current in G protein-dependent manner in rat pregnant myocyte. The current was significantly potentiated by $1{\mu}M$ lanthanides (a potent TRPC4/5 stimulator) and suppressed by $10{\mu}M$ 2-APB (TRPC4-7 inhibitor). In addition, in isometric tension experiment, SMC which was evoked by passive stretch was greatly potentiated by lanthanide ($1{\mu}M$) and suppressed by 2-APB ($10{\mu}M$), suggesting a possible involvement of TRPC4/5 channel in regulation of SMC in pregnant myometrium. These results provide a possible cellular mechanism for regulation of SMC during pregnancy and provide basic information for developing a new agent for treatment of premature labor.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.6
• /
• pp.399-406
• /
• 2013

In the present study, the flat plate model test method is developed to evaluate the skin friction of the marine coating in the cavitation tunnel. Six-component force balance is used to measure the profile drag of the flat plate and strut. LDV(laser Doppler velocimetry) technique is also employed to evaluate the drag and to figure out the reason of the drag reduction. The flow velocities above the surface can be used to assess the skin friction, combined with direct force measurement. Since the vortical structure in the coherent turbulence structure influences on the skin friction in the high Reynolds number regime, the interaction between the turbulence structure and the surface wall is paying more attention. This sort of thing is important in the passive control of the turbulent boundary layer because the skin friction can't be determined only by wall condition. As complicated flow phenomena exist around a paint film, systematic measurement and analysis are necessary to evaluate the skin friction appropriately.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.2
• /
• pp.284-291
• /
• 1997

The electrode characteristics of two kinds of metal hydride electrodes using V-Ti (V-rich) based alloy were studied, in which one electrode was prepared by sintering the mixture of V-Ti alloy and Ni powders by a rapid thermal annealing technique and the other one was prepared using V-Ti-Ni ternary alloy, The discharge capacities of all electrodes during the charge-discharge cycling were completely deteriorated within 10 cycles. It appeared that the deterioration of the electrodes was caused by the dissolution of V in the near-surface region into the electrolyte and the formation of $TiO_2$ layer on the alloy particle surface. This degradation mechanism was supported by the facts that V is main hydride forming element and $TiO_2$ has very low electrical conductivity and hydrogen diffusivity.

• The Journal of Advanced Prosthodontics
• /
• v.3 no.4
• /
• pp.177-185
• /
• 2011

PURPOSE. The aim of this study was to evaluate the effect of dimensional stability of splinting material on the accuracy of master casts. MATERIALS AND METHODS. A stainless steel metal model with 6 implants embedded was used as a master model. Implant level impressions were made after square impression copings were splinted using 5 different techniques as follows. (1) Splinted with autopolymerizing resin and sectioned, reconnected to compensate polymerization shrinkage before the impression procedure. (2) Splinted with autopolymerizing resin just before impression procedure. (3) Primary impression made with impression plaster and secondary impression were made over with polyether impression material. (4) Splinted with impression plaster. (5) Splinted with VPS bite registration material. From master model, 5 impressions and 5 experimental casts, total 25 casts were made for each of 5 splinting methods. The distortion values of each splinting methods were measured using coordinate measuring machine, capable of recordings in the x-, y-, z- axes. A one-way analysis of variance (ANOVA) at a confidence level of 95% was used to evaluate the data and Tukey's studentized range test was used to determine significant differences between the groups. RESULTS. Group 1 showed best accuracy followed by Group 3 & 4. Group 2 and 5 showed relatively larger distortion value than other groups. No significant difference was found between group 3, 4, 5 in x-axis, group 2, 3, 4 in y-axis and group 1, 3, 4, 5 in z-axis (P<.0001). CONCLUSION. Both Splinting impression copings with autopolymerizing resin following compensation of polymerization shrinkage and splinting method with impression plaster can enhance the accuracy of master cast and impression plaster can be used simple and effective splinting material for implant impression procedure.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.2
• /
• pp.255-263
• /
• 2017

An infrared-guided missile has been emerging as a major threat against combat aircraft due to its passive guidance characteristics and with recent advances in stealth technology. Hence, the infrared stealth technology and its effectiveness-evaluation technique become more significant than ever before. In this study, we applied missile aerodynamics to lethal range calculation which allowed more precise prediction. CFD analyses were newly involved in estimating drag force characteristics of an infrared-guided missile. Velocity profiles during flight period of the missile were constructed utilizing these drag characteristics and then incorporated into our in-house code to predict corresponding lethal ranges. The results showed that the present method can predict lethal range more appropriately than the previous one with constant velocity profile. As one of the results, if a fighter gains altitude more which reduces less drag of the attacking missile, then the lethal envelope increases significantly more compared to the lock-on envelope.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.8C
• /
• pp.803-811
• /
• 2002

Asynchronous Transfer Mode-Passive Optical Network(ATM-PON) Technology is one of the best solutions for implementation of broadband access network. In this paper, we propose a new Dynamic Bandwidth Allocation (DBA) algorithm for ATM-PON systems. The DBA is a key technique for data traffic management. DBA has been studied widely to allow ATM-PON to transport data traffic cost-effectively and efficiently, and currently a hot standardization issue in Full Service Access Network(FSAN) and ITU-T. The proposed DBA algorithm efficiently manages the user traffics according to their service categories. Performance of the proposed algorithm, in aspect of Cell Transfer Delay(CTD) and Cell Delay Variation(CDV), is evaluated using computer simulation.

• Journal of Korean Medicine Rehabilitation
• /
• v.23 no.4
• /
• pp.129-141
• /
• 2013

Objectives The aim of this review is to investigate clinical studies for manual therapy on Temporomandibular Joint Disorder and to propose for the better method of studies in the future. Methods We investigated recent clinical studies for manual therapy on Temporomandibular Joint Disorder via searching Pubmed, KISS, KISTI, KERIS, KMBASE and National Assembly Library. 21 domestic and overseas articles were analyzed and the journals, the authors, the published years, countries, methods, periods, techniques of chiropractic, outcome measures, and purpose of those articles were examined. Results Studies on manual therapy were mainly published via Cranio. The diagnostic criteria that most frequently adopted in the overseas articles were research diagnostic criteria for temporomandibular disorders, The technique of chiropractic that most frequently adopted in the articles was passive traction and translation of TMJ. Many of the studies were researched for effectiveness of the manual therapy as the secondary treatment. Conclusions Reviewing the recent clinical studies for manual therapy on temporomandibular joint disorder and figuring out the strong points and weak points of those studies are necessary to future studies. It is anticipated that this review would benefit the in-depth treatments for temporomandibular joint disorder in terms of Korean medicine.

• Physical Therapy Korea
• /
• v.8 no.3
• /
• pp.43-52
• /
• 2001

This study was designed to determine the effect of ankle taping and short period of walking on the treadmill on the range of motion (ROM) and proprioception at the ankle joint. Twenty healthy male subjects (mean age=24.2 yr) participated in this study. Goniometry and videotape replaying method were used to measure the ankle ROM. Passive sagittal and frontal plane motions were measured. The difference in degree between the stimulus point and the reproduced point was defined as an angular error. The measurements were performed at four different phases: pre-taping (PRT), post-taping immediately (POT), post-5 minute walking with taping (P5M), and post-10 minute walking with taping (P10M). The ankle of dominant limb was taped by a certified athletic trainer using a closed basket weave technique. Participants walked on the treadmill at 2.5 mph. The results showed that the mean of the sagittal plane motion at PRT, POT, P5M, and P10M was 53.0, 30.5, 36.2, and 40.2 degrees, respectively. The frontal plane motion at PRT, POT, P5M, and P10M was 33.6, 13.9, 15.7, and 18.6 degrees, respectively. The angular error at PRT, POT, P5M, and P10M was 5.5, 1.6, 1.8, and 1.9 degrees, respectively. After 10 minutes of walking, the sagittal plane motion and frontal plane motion was increased by 9.7 and 4.7 degrees compared with POT, respectively. The proprioception was significantly improved after the application of ankle taping. Both the restriction of frontal plane motion and proprioception improvement at the ankle joint may contribute to ankle stability during walking.