• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.112-112
• /
• 2008

최근 Ruthenium (Ru) 은 높은 화학적 안정성, 누설전류에 대한 높은 저항성, 저유전체와의 높은 안정성 등과 같은 특성으로 인해 금속층-유전막-금속층 캐패시터의 하부전극으로 각광받고 있다. 또한 Cu와의 우수한 Adhesion 특성으로 인해 Cu 배선에서의 Cu 확산 방지막으로도 주목받고 있다. 그러나 이렇게 형성된 Ru 하부전극의 각 캐패시터간의 분리와 평탄화를 위해서는 CMP 공정이 도입이 필요하다. 이러한 CMP 공정에 공급되는 Slurry 에는 부식액, pH 적정제, 연마입자 등이 첨가되는데 이때 연마입자가 응집하여 Slurry의 분산 안전성 저하에 영향을 줄수 있다. 이로 인해 응집된 Slurry는 Scratch와 Delamination 과 같은 표면 결함을 유발할 수 있으며, Slurry의 저장 안정성을 저하시켜 Slurry의 물리적 화학적 특성을 변화시킬 수 있다. 그리하여 본 연구에서는 Ru CMP Slurry에서의 Surfactant와 같은 분산 안정제에 따른 Surface tension, Zeta potential, Particle size, Sedimentation의 분석을 통해 Slurry 안정성에 대한 영향을 살펴보았다. 그 결과 pH9 조건의 31ppm Dispersant 농도에서 50%이상의 Sedimentation 상승효과를 얻을 수 있었다. 또한 선택된 Surfactant가 첨가된 Ru CMP Slurry를 제조하여 Ru wafer의 Static etch rate, Passivation film thickness 와 Wettability를 비교해 보았다. 그리고 CMP 공정을 실시하여 Ru의 Removal rate와 TEOS에대한 Selectivity를 측정해 보았다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.4
• /
• pp.378-383
• /
• 2004

Tungsten is widely used as a plug for the multi-level interconnection structures. However, due to the poor adhesive properties of tungsten(W) on SiO$_2$ layer, the Ti/TiN barrier layer is usually deposited onto SiO$_2$ for increasing adhesion ability with W film. Generally, for the W-CMP(chemical mechanical polishing) process, the passivation layer on the tungsten surface during CMP plays an important role. In this paper, the effect of oxidant on the polishing selectivity of W/Ti/TiN layer was investigated. The alumina(A1$_2$O$_3$)-based slurry with $H_2O$$_2$ as the oxidizer was used for CMP applications. As an experimental result, for the case of 5 wt％ oxidizer added, the removal rates were improved and polishing selectivity of 1.4:1 was obtained. It was also found that the CMP characteristics of W and Ti metal layer including surface roughness were strongly dependent on the amounts of $H_2O$$_2$ oxidizer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.8
• /
• pp.479-483
• /
• 2017

The effect of $NH_3$ plasma treatment on device characteristics was confirmed for an optimized thin film transistor of poly-Si formed by ELA. When C-V curve was checked for MIS (metal-insulator-silicon), Dit of $NH_3$ plasma treated and MIS was $2.7{\times}10^{10}cm^{-2}eV^{-1}$. Also in the TFT device case, it was decreased to the sub-threshold slope of 0.5 V/decade, 1.9 V of threshold voltage and improved in $26cm^2V^{-1}S^{-1}$ of mobility. Si-N and Si-H bonding reduced dangling bonding to each interface. When gate bias stress was applied, the threshold voltage's shift value of $NH_3$ plasma treated device was 0.58 V for 1,000s, 1.14 V for 3,600s, 1.12 V for 7,200s. As we observe from this quality, electrical stability was also improved and $NH_3$ plasma treatment was considered effective for passivation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.20-23
• /
• 2004

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing(CMP) process was required for the global planarization of inter-metal dielectric(IMD) layer with free-defect. However, as the IMD layer gets thinner, micro-scratches are becoming as major defects. Chemical-Mechanical polishing(CMP) of conductors is a key process in Damascene patterning of advanced interconnect structure. The effect of alternative commercial slurries pads, and post-CMP cleaning alternatives are discuss, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. Electroplated copper deposition is a mature process from a historical point of view, but a very young process from a CMP perspective. While copper electro deposition has been used and studied for decades, its application to Cu damascene wafer processing is only now gaining complete acceptance in the semiconductor industry. The polishing mechanism of Cu-CMP process has been reported as the repeated process of passive layer formation by oxidizer and abrasion action by slurry abrasives. however it is important to understand the effect of oxidizer on copper passivation layer in order to obtain higher removal rate and non-uniformity during Cu-CMP process. In this paper, we investigated the effects of oxidizer on Cu-CMP process regarding the additional volume of oxidizer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.227-230
• /
• 2004

As the organic acids were added in the slurry, zeta potential of alumina was changed to negative value and IEP value was shifted from alkaline to acidic pH. In citric acid based slurry, Cu surface continuously dissolved and etching depth linearly increased. On the contrary, passivation layer was grown on Cu surface in oxalic acid based slurry. As the platen rotation speed increased, Preston coefficient decreased in both slurries. With oxalic acid based slurry, at low velocity, removal rate is high value because of high friction force compared to citric acid based slurry. As platen velocity increased, removal of Cu in citric acid based slurry became higher value than oxalic acid based slurry. Typical lubrication behaviors were observed in both slurries. As Sommerfeld number increased, COF values gradually decreased and then re-increased. It indicated that lubrication was changed to direct contact or semi-direct contact mode to hydro-lubrication mode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.42-43
• /
• 2005

본 연구에서는 Cu 슬러리에 부식방지제인 BTA를 첨가하여 슬러리내의 과수의 농도, pH 의 변화, 연마입자의 종류에 따라 연마거동에 미치는 영향과 각 chemical 변화에 따른 Cu surface의 변화를 살펴보았다. BTA (Benzotriazole, $C_6H_4C_3H$)를 첨가함으로써 본 연구에서 시행된 pH 와 과수의 변화에 상관없이 Cu-BTA film을 형성하여 Cu의 dissolution을 최대한 억제하는 것을 확인할 수 있었다. 또 그로인해 BTA를 첨가하지 않았을 때보다 얇은 passivation layer를 형성함을 알 수 있었고 contact angle도 더 높았다. 연마율의 경우에도 BTA가 첨가됨으로써 감소됨을 확인할 수 있었고 연마입자로 alumina particle을 사용한 경우에는 pH6, 과수 10vol%이상에서는 오히려 연마율이 증가하였다. fumed silica의 경우에는 hardness가 작아 mechanical적인 제거력이 낮아 BTA가 첨가되어도 연마율에는 큰 영향이 없었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.160-163
• /
• 2005

Top emission OLED 소자의 안정성 위하여 Parylene을 보호층으로 적용하였다. 고분자화 방법을 이용하여 증착된 Parylene은 진공공정상온에서 증착가능하기 때문에 열에 의한 OLED 소자의 열화를 방지하며 높은 광투과율과 우수한 투습습성에 의하여 고효율 장수명을 OLED 소자에 적합하다. Parylene 5 ${\mu}m$ 의 광투과율은 90 %이상 측정 되었으며 투습율은 0.4849 $g/m^2day$로 측정되었다. Parylene의 보호층로서의 영향을 살펴보기 위하여, 보호층이 형성된 소자와 보호층이 형성되지 않은 소자를 제작하여 대기중에서 그 특성을 측정 비교하였다. 두 제작된 top emission OLED 소자는 최대 휘도가 1000 $cd/m^2$ 이상 측정되었으며, parylene 보호층 공정에 의한 소자의 구동 특성 변화는 나타나지 않았다. 대기중에서 초기휘도 200 $cd/m^2$로 측정된 parylene 보호층이 형성된 소자는 수명이 5 이었고, 보호층이 형성되지 않는 소자의 수명에 비하여 2배 이상 증가하였다.

• Corrosion Science and Technology
• /
• v.23 no.4
• /
• pp.310-314
• /
• 2024

The corrosion behavior of high chromium white cast iron was studied in 0.5 mol dm^-3 H₂SO₄ + 0.01 mol dm^-3 HCl solution over time through electrochemical and immersion experiments. Potentiodynamic and potentiostatic polarizations revealed active-passivation transition behavior, with critical current densities observed at -0.27 V_SSE and 0.00 V_SSE, repectively. The former potential showed preferential dissolution of primary γ phases, while the latter one showed preferential dissolution of eutectic γ phases. Immersion tests showed an exponential increase in corrosion rate, with significant acceleration observed around 1000 seconds due to the onset of eutectic γ phase dissolution. Over a 24-hour immersion period, both γ phases exhibited extensive corrosion, leaving carbides largely intact. These findings elucidate distinct corrosion behaviors of high chromium white cast iron in acidic environments, providing critical insights into material performance evaluation. Understanding these mechanisms is essential for predicting the longevity and durability of materials in corrosive conditions, thereby informing better material design and application strategies.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.170-170
• /
• 2013

We present a novel etching technique for 2-dimentional (2-D) hexagonal boron nitride (h-BN) by using capacitively coupled plasma (CCP) of oxygen combined with a post-treatment by de-ionized (DI) water. Oxygen CCP etching process for h-BN has been systematically studied. It is found that a passivation layer was generated to obstruct further etching while it can be easily and radically removed by DI water. An essential cleaning effect also has been observed in the etching process, organic residues are successfully removed and the surface roughness has much decreased. Considering h-BN is the most important 2-D dielectric material and its potential application for graphene to silicon-based electronic devices, such an etching method can be widely used to control the 2-D h-BN thickness and improve the surface quality.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.4
• /
• pp.221-225
• /
• 2014

Although gold wire bonding techniques have already matured in semiconductor manufacturing, weakly bonded wires in semiconductor chip assembly can jeopardize the reliability of the final product. In this paper, weakly bonded or failed aluminum bonding pads are analyzed using X-ray photoelectron spectroscopy (XPS), Auger electron Spectroscopy (AES), and energy dispersive X-ray analysis (EDX) to investigate potential contaminants on the bond pad. We found the source of contaminants is related to the dry etching process in the previous manufacturing step, and fluorocarbon plasma etching of a passivation layer showed meaningful evidence of the formation of fluorinated by-products of $AlF_x$ on the bond pads. Surface analysis of the contaminated aluminum layer revealed the presence of fluorinated compounds $AlOF_x$, $Al(OF)_x$, $Al(OH)_x$, and $CF_x$.