• YAKHAK HOEJI
• /
• v.34 no.3
• /
• pp.206-211
• /
• 1990

Total suspended particles were collected and size-fractionated by an Andersen high-volume air sampler at Chungang University located near the Han River, Seoul, Korea, during the period form March, 1986 to August, 1986 and from March, 1987 to February, 1988. The concentrations and the particle size distributions of anions such as chloride, nitrate and sulfate were determined by ion chromatography. The averages of concentrations were $125.43\;{\mu}g/m^3$ in 1986 and $189.19\;{\mu}g/m^3$ in 1987 for total suspended particles (TSP), $2.12\;{\mu}g/m^3$ in 1986 and $4.14\;{\mu}g/m^3$ in 1987 for chloride, $4.39\;{\mu}g/m^3$ in 1986 and $5.95\;{\mu}g/m^3$ in 1987 for nitrate and $11.98\;{\mu}g/m^3$ in 1986 and $19.29\;{\mu}g/m^3$ in 1987 for sulfate. Size distribution of TSP was found to be generally bimodal. Chloride exhibited a seasonal variation in the distribution; fine particles were predominant in the winter whereas the concentration of coarse ones was almost same through four seasons. Nitrate showed a distribution similar to that of chloride. Such variation was less significant for sulfate. For chloride and nitrate, the relationship between the monthly averaged distribution pattern and air temperature was analyzed in terms of fine fraction (FF). The FF decreased with increasing air temperature.

• Journal of the Korean Magnetics Society
• /
• v.8 no.3
• /
• pp.125-130
• /
• 1998

13Cr-1.5Nb-Fe alloy powder was fabricated by water atomization method, and ring-shape specimen of this composition was fabricated by oil press, and then sintered in the vacuum furnace. Powder shape, size distribution, composition (C, N, O, S) analysis and saturation magnetization of as-prepared 13Cr-1.5Nb-Fe alloy powder were investigated. Ac permeability and power loss was measured after forming and sintering process. Saturation magnetization and contents of oxygen of the alloy powder is160 emu/g and about 6000 ppm, respectively. 50 % volume fraction indicate particle size of 70$\mu$m. The ac permeability of sintered specimen increases with increasing sintering temperature and forming pressure. The power loss is 107 W/cc at sintering temperature of 1200 $^{\circ}C$, 12 ton/$\textrm{cm}^2$ forming pressure, and 20 KHz. It is the lowest among the prepared specimen.

• YAKHAK HOEJI
• /
• v.29 no.4
• /
• pp.176-182
• /
• 1985

As a part of the studies on adsorptive properties of Korean halloysite clays, Hadong white clays of premium grade were examined for geometric pore structured by mercury porosimetry and for specific surface areas by nitrogen adsorption according to the BET procedure. Three size fractions of the native clay sample were derived from passage BS #100, #200 and #325 meshes, respectively. Several parameters lhus observed in relation to the pore structures are shown below: 1. The size fraction of BS #100, #200 and #325 show internal pore volumes of 25.3, 30.2 and $35.0m^2g^{-1}$, respectively. 2. In the distribution curves of the cumulative pore volume against pore diameter, it has been shown that the larticle sizes, the steeper the distribution over the larger ranges of pore diameters. The converse is true the smaller particles. 3. Internal pore areas increase with decrease in pore sizes. It follows that the pores having diameters of $\leq$0.1$\mu\textrm{m}$ are responsible for more than 90% of the total pore area. 4. The behaviour of nitrogen adsorption can be best described by BET type IV isotherm. Further, the hysteresis loops of the adsorptiondesorption curves become narrower with decresing particle sizes. 5. The specific surface areas observed for the fractions of BS #100, BS #200 and BS #325 are 34.6, 35.4 and 43.2m $^2g^{-1}$, respectively. and the calcined clay of BS #325 has a specific surface area near $30.4m^2g^{-1}$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.9
• /
• pp.496-504
• /
• 2009

In order to investigate the feasibility of a direct ice slurry transporting system for the purpose of district cooling, a case study of field application is performed. The research aims include the field measurement of ice packing factor, the performance of coldness delivery, and the branching characteristics of ice slurry. Two representative types of pipe branch are dealt with in this work. For the slurry flow with ice volume fraction of 0.16 or less, the pipe blocking due to aggregation is not observed. Based on the time-wise variation of temperature in the storage tank, a calculating method of ice packing factor is newly developed, which seems to be useful when the brine concentration is unknown. It is confirmed that the mass flow rate of ice slurry per unit cooling load is markedly reduced with increasing the ice content. The pumping power also decreases, but remains unchanged for high ice fractions. The distribution of ice particle before and after branching shows a good uniformity within the range of 5% difference, but yields a unique trend depending on the flow rate.

• Korean Journal of Materials Research
• /
• v.15 no.12
• /
• pp.824-828
• /
• 2005

In this study the effect of the content of $TiB_2$ on wear properties was investigated. $Cu-TiB_2$ composites have been fabricated by hot extrusion. Sliding wear tests were peformed by a pin-on-disk type wear test machine under dry condition and loads varied with from 20N to 80N at sliding speed 3.5Hz. The test results showed that the wear losses and the friction coefficients decreased with increasing $Cu-TiB_2$ volume fraction and increasing the size of $Cu-TiB_2$ particle. Wear property of $10{\mu}m,\;5 vol\%\; TiB_2$ specimen was excellent all of the wear specimens. It is thought that the increase of plastic flow resistivity due to uniform distribution of $10{\mu}m,\;5 vol\%\; TiB_2$ wear specimen would improve wear property. The worn surface and wear debris were examined by optical microscope and scanning electron microscope.

• Korean Journal of Materials Research
• /
• v.15 no.1
• /
• pp.61-65
• /
• 2005

The titanium $diboride(TiB_2)$ has high strength(750MPa), high melting point $(3225^{\circ}C)\;and\;10\%$ IACS electrical conductivity. On this account, the dispersion hardening $Cu-TiB_2$ composites(MMCs) are a promising candidate for applications as electrical contact materials. MMCs for electrical contact materials can reduce material cost and resource consumption caused by wear, due to its good mechanical and electrical property. In this study, we attempt to prepare MMCs with various volume fraction and particle size of $TiB_2$ by means of hot extruded and cold drawn process. Dry sliding wear tests were performed on a pin-on-disk type wear tester, sliding against SM45C under the different applied loads. After wear testing, the microstructures of the worn surfaces were observed by SEM and the microhardnesses of the subsurface zone were measured.

• Steel and Composite Structures
• /
• v.33 no.3
• /
• pp.463-472
• /
• 2019

Initial thermo-elastic and steady state creep deformation of a rotating functionally graded simple blade is studied using first-order shear deformation theory. A variable thickness model for cantilever beam has been considered. The blade geometry and loading are defined as functions of length so that one can define his own blade profile and loading using any arbitrary function. The blade is subjected to a transverse distributed load, an inertia body force due to rotation and a distributed temperature field due to a thermal gradient between the tip and the root. All mechanical and thermal properties except Poisson's ratio are assumed to be longitudinally variable based on the volume fraction of reinforcement. The creep behaviour is modelled by Norton's law. Considering creep strains in stress strain relation, Prandtl-Reuss relations, Norton' law and effective stress relation differential equation in term of effective creep strain is established. This differential equation is solved numerically. By effective creep strain, steady state stresses and deflections are obtained. It is concluded that reinforcement particle size and form of distribution of reinforcement has significant effect on the steady state creep behavior of the blade.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.36 no.1
• /
• pp.1-16
• /
• 2010

The preparation and properties of emulsions stabilized by the adsorption of solid particles at the oil-water interface are reviewed. Comparison is made with the behaviour of surfactant-stabilized emulsions. Many of the properties of Pickering emulsions are attributed to the large free energy of adsorption for particles. The main differences is due to the irreversible adsorption of particles to the interface. Phase inversion from w/o (water-in-oil) to o/w (oil-in-water) can be brought by increasing the volume fraction of water. Hydrophilic particles tend to form o/w emulsion whereas hydrophobic particles form w/o emulsion. The contact angle at the oil-water interface is main parameter to decide the emulsion type. The aspects of stability of Pickering emulsions are in contrast to general emulsions in some points. The possibility using Pickering emulsions for cosmetics is also proposed.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.162-167
• /
• 2006

Nanofluid is a kind of new engineering material consisting of nanoparticles dispersed in base fluid. Nanofluids could have various applications such as magnetic fluids, heat exchanger working fluids, lubricants, drug delivery and so on in present study, various nanoparticles, such as MWCNT (Multi-walled Carbon Nanotube), fullerene, copper oxide, and silicon dioxide are used to produce nanofluids. As base fluids, DI-water, ethylene glycol, oil, and silicon oil are used. To investigate the thermo-physical properties of nanofluids, thermal conductivity and kinematic viscosity are measured. Stability estimation of nanofluid is conducted with UV-vis spectrophoto-meter. In this study, the high pressure homogenizer is the most effective method to produce nanofluid with the prepared nanoparticle and base fluid. Excellently stable nanofluids are produced with the magnetron sputtering system. Thermal conductivity of nanofluid increases with increasing particle volume fraction except water-based fullerene nanofluid which has lower thermal conductivity than base fluid due to its lower thermal conductivity, 0.4 W/mK. The experimental results can't be predicted by Jang and Choi model.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.78-86
• /
• 2019

Aluminum, which is a metal fuel contained in the composite solid propellant, is not ignited and burned on the combustion surface by the oxide film, and it partially melts and coalesces with surrounding aluminum particles. For the evaluation and design of the propellant performance, modeling was performed to predict the size and distribution of agglomerated particles, and the size and distribution of agglomerates were compared and verified through experiment. The predicted values showed the tendency to decrease with pressure as in the experiment, but the error increased as the pressure increased. The agglomerated particle distribution graph showed a difference in the volume fraction although the diameter at the peak was the same.