• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.414-423
• /
• 2006

Many construction projects adopt grouting technology to prevent the leakage of groundwater or to improve the shear strength of the ground. Recognition as a feasible field procedure dates back to 1925, Since then, developments and field use have increased rapidly. According to improvement of grout materials, theoretical study on grout penetration characteristics is demanded. Fluid of grout always tends to flow from higher hydraulic potential to lower and the motion of grout is also a function of formation permeability. Viscosity of grout is changed by chemical action while grout moves through pores. Due to the increment of viscosity, permeability is decreased. Permeability is also reduced by grout particle deposits to the soil aggregates. In this thesis, characteristics of new cement grout material that is developed recently is studied: injectable volume of new grout material is tested in two different sizes of sands, and the method to calculate injectable volume of grout is suggested with consideration of change in viscosity and clogging phenomena. The calculated values are compared with injection test results. Viscosity of new grout material is found to be an exponential function of time. And lumped parameter $\theta$ of new grout material to be used for assessing deposition characteristics is estimated by comparing deposit theory with injection test results considering different soil types and different injection pressure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.471.2-471.2
• /
• 2014

We demonstrate here that an improvement in precursor film density (green density) leads to a great enhancement in the photovoltaic performance of CuInSe2 (CISe) thin film solar cells fabricated with Cu-In nanoparticle precursor films via chemical solution deposition. A cold-isostatic pressing (CIP) technique was applied to uniformly compress the precursor film over the entire surface (measuring 3~4 cm2) and was found to increase its relative density (particle packing density) by ca. 20%, which resulted in an appreciable improvement in the microstructural features of the sintered CISe film in terms of lower porosity, reduced grain boundaries, and a more uniform surface morphology. The low-bandgap (Eg=1.0 eV) CISe PV devices with the CIP-treated film exhibited greatly enhanced open-circuit voltage (VOC, from 0.265 V to 0.413 V) and fill factor (FF, from 0.34 to 0.55), as compared to the control devices. As a consequence, an almost 3-fold increase in the average power conversion efficiency, 3.0 to 8.2% (with the highest value of 9.02%), was realized without an anti-reflection coating. A diode analysis revealed that the enhanced VOC and FF were essentially attributed to the reduced reverse saturation current density (j0) and diode ideality factor (n). This is associated with the suppressed recombination, likely due to the reduction in recombination sites such as grain/air surfaces (pores), inter-granular interfaces, and defective CISe/CdS junctions in the CIP-treated device. From the temperature dependences of VOC, it was confirmed that the CIP-treated devices suffer less from interface recombination.

• Korean Journal of Materials Research
• /
• v.28 no.1
• /
• pp.6-11
• /
• 2018

There are various manufacturing processes for pure $SiO_2$ that is used as abrasives, chemicals, filters, and glasses, and in metallurgy and optical industries. In the optical fiber industry, to produce $SiO_2$ preform, $SiCl_4$ is utilized as a raw material. However, the combustion reaction of $SiCl_4$ has caused critical environmental issues, such as ozone deficiency by chlorine compounds, the greenhouse effect by carbon dioxide and corrosive gas such as hydrochloric acid. Thus, finding an alternative source that does not have those environmental issues is important for the future. Octamethylcyclotetrasiloxane (OMCTS or D4) as a chlorine free source is recently promising candidate for the $SiO_2$ preform formation. In this study, we first conducted a vaporizer design to vaporize the OMCTS. The vaporizer for the OMCTS vaporization was produced on the basis of the results of the vaporizer design. The size of the primary particle of the $SiO_2$ formed by OMCTS was less than 100 nm. X-ray diffraction patterns of the $SiO_2$ indicated an amorphous phase. Fourier-transform infrared spectroscopy analysis revealed the Si-O-Si bond without the -OH group.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.1 no.1
• /
• pp.46-54
• /
• 1996

A study on the concentrations of total suspended matters (TSM) and their distribution pattern was conducted off the west coast of Tae-An Peninsula during the spring season. Especially non-destructive and fine-tuned analysis for the size-distribution of suspended matters was made using SPECTREX instrument. Water masses were characterized by the typical tidal front, with vertically homogenous coastal waters and the strong thermoclines on the offshore area. Concentrations of suspended matters were generally less than 10 mg/l, but the concentrations increased up to 25 mg/l at the bottom waters and mid-depth waters. Mean particle size of the suspended matters were generally 5-6$\mu\textrm{m}$ and 8-10$\mu\textrm{m}$ for the fine-grained suspended matters and the coarse-grained suspended matters, respectively. They are considered to be composed dominantly of detrital materials. On the coastal area, landward side of tidal front, bottom sediments can be easily resuspended by the strong tidal currents, and therefore, deposition of suspended materials are thought to be rather limited. On the offshore area, however, suspended sediments mostly supplied from the northern part of the present study area near Kyunggi Bay are thought to be transported southward and/or southwestward along the mid- depth layer of strong thermocline.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.312-312
• /
• 2011

In SiH4/H2 discharge for growth process of hydrogenated amorphous silicon (a-Si:H), silane polymers, produced by SiH2 + Sin-1H2n ${\rightarrow}$ SinH2n+2, have no reactivity on the film-growing surface. However, under the SiH2 rich condition, high silane reactive species (HSRS) can be produced by electron collision to silane polymers. HSRS, having relatively strong reactivity on the surface, can react with dangling bond and form Si-H2 networks which have a close correlation with photo-induced degradation of a-Si:H thin film solar cell [1]. To find contributions of suggested several external plasma conditions (pressure, frequency and ratio of mixture gas) [2,3] to suppressing productions of HSRS, some plasma characteristics are studied by numerical methods. For this study, a zero-dimensional global model for SiH4/H2 discharge and a one-dimensional particle-in-cell Monte-Carlo-collision model (PIC-MCC) for pure SiH4 discharge have been developed. Densities of important reactive species of SiH4/H2 discharge are observed by means of the global model, dealing 30 species and 136 reactions, and electron energy probability functions (EEPFs) of pure SiH4 discharge are obtained from the PIC-MCC model, containing 5 charged species and 15 reactions. Using global model, SiH2/SiH3 values were calculated when pressure and driving frequency vary from 0.1 Torr to 10 Torr, from 13.56 MHz to 60 MHz respectively and when the portion of hydrogen changes. Due to the limitation of global model, frequency effects can be explained by PIC-MCC model. Through PIC-MCC model for pure SiH4, EEPFs are obtained in the specific range responsible for forming SiH2 and SiH3: from 8.75 eV to 9.47 eV [4]. Through densities of reactive species and EEPFs, polymerization reactions and production of HSRS are discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.183-183
• /
• 2012

In the era of 45 nm or beyond technology, conventional etch mask using photoresist showed its limitation of etch mask pattern collapse as well as pattern erosion, thus hard mask in etching became necessary for precise control of etch pattern geometry. Currently available hard mask materials are amorphous carbon and polymetric materials spin-on containing carbon or silicon. Amorphous carbon layer (ACL) deposited by PECVD for etch hard mask has appeared in manufacturing, but spin-on carbon (SOC) was also suggested to alleviate concerns of particle, throughput, and cost of ownership (COO) [1]. SOC provides some benefits of reduced process steps, but it also faced with wiggling on a sidewall profile. Diamond like carbon (DLC) was also evaluated for substituting ACL, but etching selectivity of ACL was better than DLC although DLC has superior optical property [2]. Developing a novel material for pattern hard mask is very important in material research, but it is also worthwhile eliminating a potential issue to continuously develop currently existing technology. In this paper, we investigated in-situ dry-cleaning (ISD) monitoring of ACL coated process chamber. End time detection of chamber cleaning not only provides a confidence that the process chamber is being cleaned, but also contributes to minimize wait time waste (WOW). Employing Challenger 300ST, a 300mm ACL PECVD manufactured by TES, a series of experimental chamber cleaning runs was performed after several deposition processes in the deposited film thickness of $2000{\AA}$ and $5000{\AA}$. Ar Actinometry and principle component analysis (PCA) were applied to derive integrated and intuitive trace signal, and the result showed that previously operated cleaning run time can be reduced by more than 20% by employing real-time monitoring in ISD process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.198-198
• /
• 2011

단분산 결정질 실리콘 나노입자 (<10 nm)는 양자점 효과로 인한 선택적 파장 흡수가 가능하므로 태양전지 분야에 응용 가능성이 크다. 특히 입경의 크기가 작아지면 부피대비 표면적이 넓어지기 때문에 태양빛 흡수 면적이 증가한다. 따라서 입자의 크기는 태양전지에서 효율을 결정하는 중요한 요소 중 하나이다. 이러한 이유에서 plasma arc synthesis, laser ablation, pyrolysis 그리고 PECVD (Plasma Enhanced Chemical Vapor Deposition) 등이 실리콘 나노입자를 합성하는데 연구되어 왔으며, 특히 PECVD는 입자 생성과 동시에 균일한 증착이 이루어질 수 있기 때문에 태양전지 제작 시 공정 효율을 높일 수 있다. PECVD를 이용한 나노입자 합성에서 입경을 제어하는데 중요한 전구물질은 Ar과 SiH4가스이다. Ar 가스는 ICP (Inductively Coupled Plasma) 챔버 내부에 가해준 전력을 통해 가속됨으로써 분해되어 Ar plasma가 생성된다. 이는 공급되는 SiH4가스를 분해시켜 핵생성을 유도하고, 그 주위로 성장시킴으로써 실리콘 나노입자가 합성된다. 이때 중요한 변수 중 하나는 핵생성과 입자성장시간의 조절을 통한 입경제어 이다. 또한 공급되는 가스의 유량은 입자가 생성될 때 필요한 화학적 구성비를 결정하므로 입경에 중요한 요소가 된다. 마지막으로 공정압력은 챔버내부의 plasma 구성 요소들의 평균 자유 행로를 결정하여 SiH4가 분해되어 입자가 생성되는 속도와 양을 제어한다. PECVD를 이용한 실리콘 나노입자 형성의 주요 변수는 RF pulse, 가스(Ar, SiH4, H2)의 유량, Plasma power, 공정압력 등이 있다. 본 연구에서는 RF (Radio Frequency) PECVD방법을 이용하여 실리콘 나노입자를 만드는데 필요한 여러 변수들을 제어함으로써 이에 따른 입경분포 차이를 연구하였다. 또한 SEM (Scanning Electron Microscopy)과 SMPS (Scanning Mobility Particle Sizer)를 이용하여 각 변수에 따라 생성된 나노입자의 입경과 농도를 분석하였다. 이 중 plasma power에 따른 입경분포 측정 결과 600W에서 합성된 실리콘 나노입자가 상당히 단분산 된 형태로 나타남을 확인할 수 있었고 향후 다른 변수의 제어, 특히 DC bias 전압과 열을 가함으로써 나노입자의 결정성을 확인하는 추가 연구를 통해 태양전지 제작에 응용 할 수 있을 것으로 예상된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.391-391
• /
• 2011

최근 나노에 대한 연구가 활성화되고 나노입자가 가지는 특성이 부각되면서 이를 소자 제조에 응용하고자 하는 연구가 집중적으로 이루어지고 있다. 박막에 포함된 나노입자는 메모리, 고효율 박막형 태양전지 등에 이용될 수 있는 가능성을 보여주었으며, 나노입자를 바탕으로 소자 제조에 관한 연구가 이루어지면서 플라즈마 내 발생하는 나노입자를 이용하여 패터닝 등에 적용하고자 하는 연구가 국내외에서 활발히 이루어지고 있다. 특히 플라즈마에서 발생하는 나노입자는 플라즈마 내 전기적 및 화학적 특징으로 인해 다른 입자 제조 공정과 달리 응집이 없는 균일한 입자를 제조할 수 있다. 이러한 플라즈마 내 발생 입자를 응용하기 위해서는 공정 조건에 따른 입자의 생성 및 성장 분석이 필요하다. 하지만 이러한 입자 발생 특성에 관한 연구는 기존에 밝혀진 반응 메커니즘으로 인해 수치해석적 연구는 체계적으로 진행되었으나 실험적 연구의 경우 적합한 측정 장비의 부재로 인해 제한이 있었다. 따라서 본 연구에서는 저압에서 실시간으로 나노입자 분포를 측정할 수 있는 PBMS (particle beam mass spectrometer)를 이용하여 나노입자 합성 공정 중 발생하는 입자의 존재를 확인하고 특성을 분석하였다. 실리콘 나노 입자의 측정은 PBMS 장비의 전단 부분을 PECVD (plasma enhanced chemical vapor deposition) 장치 내부에 연결하여 진행하였다. PECVD를 이용한 실리콘 나노입자 형성의 주요 변수는 RF pulse, 가스(Ar, SiH4, H2)의 유량, Plasma power, 공정압력 등이 있다. 본 연구에서는 실리콘 나노입자를 만드는데 필요한 여러 변수들을 제어함으로써 이에 따른 입경분포를 측정하였다. 또한 동일한 조건에서 생성 나노입자를 포집하여 TEM과 SEM을 이용하여 분석하여 그 결과를 비교하였다. 추후 지속적 연구에 의해 변수에 따른 나노입자 생성을 데이터베이스화 하여 요구되는 응용분야에 적합한 특성을 가지는 나노입자를 형성하는 조건을 정립 하는데 중요한 역할을 할 것을 기대할 수 있다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.304-304
• /
• 2011

열필라멘트 화학 기상 증착 공정(HWCVD, hot wire chemical deposition)은 낮은 기판 온도에서 다결정 실리콘 박막을 빠른 속도로 증착할 수 있는 방법이다. 이는 후처리가 없어도 전기적 특성이 우수한 박막을 저온에서 얻을 수 있기 때문에 녹는점이 낮은 기판에 증착을 할 수 있으며 공정비용 절감 효과가 있다. 이러한 박막 증착 공정 중 기상 핵생성에 의해 나노 입자가 생성되며, 새로운 관점에서는 그 농도와 크기가 박막 성장에 중요한 변수로 작용한다. 따라서 공정조건의 변화에 따라 생성되는 나노 입자의 크기 분포를 실시간으로 분석하여 박막 형성의 최적 조건을 찾는 연구가 필요하다. 하지만 이러한 입자 발생 특성에 관한 연구는 기존에 밝혀진 반응 메커니즘으로 인해 수치해석적 연구는 체계적으로 진행되었으나 실험적 연구의 경우 적합한 측정장비의 부재로 인해 제한이 있었다. 따라서 본 연구에서는 저압에서 실시간으로 나노입자 분포를 측정할 수 있는 PBMS (particle beam mass spectrometer)를 이용하여 열필라멘트 화학 기상 증착 공정 중 발생하는 입자의 존재를 확인하고 특성을 분석하였다. 실리콘 나노 입자의 측정은 PBMS 장비의 전단 부분을 HWCVD 배기 라인에 연결하여 진행하였으며 반응기 내 샘플링 위치, 필라멘트 온도, 챔버 압력, 작동기체의 비율을 변수로 하여 진행하였다. 그 결과 실리콘 나노 입자는 양 또는 음의 극성을 가진 하전된 상태임을 확인 하였고, 측정 조건에 따라 일부 단일 극성으로 존재하였다. 한편, 필라멘트 온도가 증가할수록 하전된 나노입자의 최빈값은 감소하였다. 또한 반응 가스인 SiH4 농도가 증가할수록 최빈값은 농도에 비례하여 증가하였다. 이런 결과는 기존 HWCVD 실험에서 투과 전자 현미경(TEM)을 이용하여 분석한 실리콘 나노 입자의 크기 분포 결과와 경향이 일치함을 확인하였다. 본 연구를 통하여 확인된 하전된 나노 입자의 존재를 실험적으로 확인하였으며 추후 지속적 연구에 의해 이러한 하전된 나노 입자가 박막 형성에 기여 하는 것을 규명하고 박막 형성 조건을 최적화하는데 중요한 역할을 할 것을 기대할 수 있다.

• Korean Journal of Materials Research
• /
• v.12 no.4
• /
• pp.296-303
• /
• 2002

For potential application to quantum mechanical devices, nano-composite thin films, consisting of GaAs quantum dots dispersed in SiO$_2$ glass matrix, were fabricated and studied in terms of structural, chemical, and optical properties. In order to form crystalline GaAs quantum dots at room temperature, uniformly dispersed in $SiO_2$matrix, the composite films were made to consist of alternating layers of GaAs and $SiO_2$in the manner of a superlattice using RF magnetron sputter deposition. Among different film samples, nominal thickness of an individual GaAs layer was varied with a total GaAs volume fraction fixed. From images of High Resolution Transmission Electron Microscopy (HRTEM), the formation of GaAs quantum dots on SiO$_2$was shown to depend on GaAs nominal thickness. GaAs deposits were crystalline and GaAs compound-like chemically according to HRTEM and XPS analysis, respectively. From measurement of optical absorbance using a spectrophotometer, absorption edges were determined and compared among composite films of varying GaAs nominal thicknesses. A progressively larger shift of absorption edge was noticed toward a blue wavelength with decreasing GaAs nominal thickness, i.e. quantum dots size. Band gaps of the composite films were also determined from Tauc plots as well as from PL measurements, displaying a linear decrease with increasing GaAs nominal thickness.