• 제목/요약/키워드: Particle Volume Concentration

검색결과 198건 처리시간 0.026초

제주도 고산에서의 1994년 여름 측정: (I) 입자 이온 조성 (Measurements at Kosan, Cheju Island during the Summer, 1994: (I) Aerosol Ion Composition)

  • 김용표;김성주;진현철;백남준;이종훈;김진영;심상규;강창희;허철구
    • 한국대기환경학회지
    • /
    • 제12권3호
    • /
    • pp.297-305
    • /
    • 1996
  • Aerosol measurements were carried out at Kosan, Cheju Island, Korea for the period from July 20 to August 10, 1994. Total suspended particles were collected by high volume samplers and PM 2.5 particles with gaseous volatile species were collected by a filter pack sampler and their ionic composition are analyzed. The average mass concentration of PM 2.5 particles was comparable to that of PM 3 particles collected during March, 1994 at the same site but the average non sea-salt sulfate concentration was higher that that of PM 3 particles, implying the fraction of anthropogenic air apllutants during this period is higher than that during March, 1994. During the measurement period, two distincitive patterns were observed, high concentrations of mass and water soluble ions were observed between July 20 and August 1 while those during after August 2 were low. Back trajectory analysis results show that air masses arriving at Kosan during the earlier period were mainly from Korea and Japan while those during the later period were from the North Pacific Ocean. It is suggested that the particle ion concentrations during the later period are marine background concentrations at Kosan during the summertime.

  • PDF

대기오염 물질인 $SO_2$ 제거반응 특성 연구 (A Study on the Removal Reaction Characteristics of Sulfur Dioxide)

  • 강순국;정명규
    • 한국환경과학회지
    • /
    • 제4권1호
    • /
    • pp.41-52
    • /
    • 1995
  • The effects of reaction temperature, SO2 and CO2 concentration in an air gas stream, particle sizes of limestone on the reactivity and capacity of SO2 removal have been determined in a thermogravimetric analyser(TGA). The apparent reaction order of sulfation reaction of pre-calcined lime(CaO) with respect to SO2 is found to be close to unity. The apparent activation energies are found to be 17,000 kcal/kmol for sulfation of pre-calcined lime and 19,500 kcal/kmol for direct sulfation of limestone(CaCO3). The initial sulfation reaction rate of pre-calcined lime increases with increasing temperature, whereas the sulfur capture capacity exhibits a maximum value at 90$0^{\circ}C$. In direct sulfation of limestone, sulfation reactivity and sulfur capature capacity of sorbent increase with increasing temperature and decreasing CO2 concentration in a gas bulk stream. The main pare of pre-calcined lime is shifted to the larger pore sizes and pore volume decreases with increasing sulfation time and temperature. The surface area of lime decreases with increasing calcination temperature under an air atmosphere, whereas is yearly constant under a CO2(5, 10%) atmosphere in a gas stream.

  • PDF

연속회분식반응기 공정의 하이드로사이클론 도입 하수처리 최적 운전특성 (Optimal Operational Characteristics of Wastewater Treatment Using Hydrocyclone in a Sequencing Batch Reactor Process)

  • 권규태;김현구;안대희
    • 한국환경과학회지
    • /
    • 제31권4호
    • /
    • pp.295-309
    • /
    • 2022
  • The purpose of this study was to evaluate the operational characteristics of wastewater treatment using Sequencing Batch Reactor (SBR) with Aerobic Granular Sludge (AGS) separator in the pilot plant. Pilot plant experiments were conducted using SBR with AGS separator and pollution removal efficiencies were evaluated based on the operational condition and surface properties of AGS. The results of the operation on water quality of the effluent showed that the average concentration of total organic carbon, suspended solids, nitrogen, and phosphorus was 6.89 mg/L, 7.33 mg/L, 7.33 mg/L, and 0.2 mg/L, respectively. All these concentrations complied the effluent standard in Korea. The concentration of mixed liquor suspended solid (MLSS) fluctuated, but the AGS/MLSS ratio was constant at 86.5±1.3%. Although the AGS/MLSS ratio was constant, sludge volume index improved. These results suggested that the particle discharged fine sludge and increased the AGS praticle size in the AGS. Optical microscopy revealed the presence of dense AGS at the end of the operation, and particles of > 0.6 mm were found. Compared to those of belt-type AGS separator, the required area and power consumption of the hydrocyclone-type AGS separator were reduced by 27.5% and 83.8%, respectively.

국내 중소 도시지역 강우유출수의 유출특성 (Runoff Characteristics of Stormwater in Small City Urban Area)

  • 이홍신;이승환
    • 대한환경공학회지
    • /
    • 제31권3호
    • /
    • pp.193-202
    • /
    • 2009
  • 본 연구는 국내 중소 도시지역에서 강우 시 발생하는 강우유출수의 유출경향을 분석하고 초기강우기준을 산정하기 위하여 수행되었다. 연구지역은 국가산업단지가 소속되어 있는 구미시 원평동의 주거지역으로 선정 되었으며 모니터링 기간은 3개월에 걸쳐 시행되었다. 연구지역의 유역면적은 24.9 ha이고, 토지이용형태는 주거지역으로 대상유역의 80%가 불투수 면적(포장의 형태: 아스팔트)인 것으로 나타났다. 모니터링은 총 6회의 강우사상에 대하여 실시하였으며 모든 수질항목에 대해 EMC (Event Mean Concentration)와 SMC (Site Mean Concentration)를 산정하였다. 또한 강우지속시간에 따른 입경크기분포의 변화와 초기세척 현상을 관찰하였는데, 입경크기분포는 10%입경($D_{0.1}$), 50%입경($D_{0.5}$, 90%입경($D_{0.9}$이 각각 9.82 ${\mu}m$, 38.99 ${\mu}m$, 159.61 ${\mu}m$로 나타났고, 초기세척 현상은 용존성 물질보다 입자성 물질이 더 강하게 나타났다. $MFF_n$ (Mass first flush)을 이용하여 초기강우기준을 검토한 결과 초기우수유출수의 부피 30%에 오염물질부하량의 부피 44.4~58.5%를 포함하고 있는 것으로 나타났다. $MFF_n$과 입경크기분포는 자연형, 장치형 시설과 같은 다양한 비점오염저감시설의 설계 및 운전과 초기강우기준 결정을 위한 정보를 제공할 수 있을 것으로 기대된다.

지하역사 승강장에서 코로나19 바이러스 공기감염 대응 공기조화기와 공기청정기의 적용 효과 비교 (Comparison of applicability of HVAC and air cleaners in a subway station platform against airborne infection of SARS-CoV-2)

  • 이건희;김상복;박인용;홍기정;이예완;김학준;김용진;한방우
    • 한국입자에어로졸학회지
    • /
    • 제18권3호
    • /
    • pp.51-59
    • /
    • 2022
  • In this work, virion concentration and its dose changes by HVAC and air cleaners were estimated in a subway station platform to control airborne infection of SARS-CoV-2. Collection efficiencies with particle size were measured for the air filter equipped in a HVAC in one subway station in Daejeon. Indoor PM2.5 changes according to outdoor PM2.5 with time were also measured to estimate air infiltration rate in the subway station platform. When infected persons generate virions by 104, 105, 106, 3 × 106 and 5 × 106 h-1 in a 2,400 m3 volume platform, the concentration and dose were estimated as 9, 92, 275 and 458 virions/m3 and 4, 43, 130 and 217 virions after 1 hour exposure, respectively. The concentration and dose were reduced by 70%, and 64%, respectively by operations of both HVAC (with a flow rate of 16,000 m3/h, MERV 11) and ten air cleaners(with total CADR 10,740 m3/h) compared to those without operation of both HVAC and air cleaners. However, virion dose in the platform was estimated to be too low at the general conditions due to a large space, a high air infiltration (3 h-1) and a short residence time (usually < 10 mins) in the platform irrespective of the operations of HVAC or air cleaners. HVAC with filters and air cleaners would be more necessary in the concourse or shopping areas in the subway stations to reduce the infection dose from a few hundred to several tens virions in a hour.

대체 연료인 DME 혼합에 의한 대향류 에틸렌 확산화염내 매연 생성에 대한 실험적 연구 (Experimental Study on Soot Formation in Opposed-Flow Ethylene Diffusion Flames by Mixing DME as an Alternative Fuel)

  • 윤두호;윤석훈;최재혁
    • 해양환경안전학회지
    • /
    • 제16권3호
    • /
    • pp.301-306
    • /
    • 2010
  • DME는 환경 친화적인 특성으로 인해 현재 전 세계적으로 주목을 받고 있다. 지금까지 DME는 매연을 적게 생산하는 청정 에너지라는 특성으로 인해 디젤 자동차의 주요 대체 에너지로서 연구되어 왔다. 이에 본 연구에서는 에틸렌 대향류 확산화염에 DME를 5%, 14% 및 30% 혼합했을 때, DME의 혼합 비율에 따른 매연의 수밀도 및 크기에 대한 영향을 조사하였다. 레이저 투과법 및 산란법을 이용해 수밀도 및 크기를 측정하였다. 그 결과 DME를 30% 혼합한 경우에는 매연이 감소한 반면, 5%와 14%의 혼합 비율에서는 매연이 증가하는 경향을 나타내었다. 이 결과는 DME가 매연 생성이 적은 청정 연료로 알려진 것과는 달리 에틸렌 확산화염 내에서는 DME의 혼합에 따라 매연 생성이 증가될 수 있다는 것을 의미한다.

고밀도 폴리에틸렌 분진의 열분해성과 착화에너지 (Pyrolysis Characteristic and Ignition Energy of High-Density Polyethylene Powder)

  • 한우섭;이정석
    • 한국가스학회지
    • /
    • 제18권3호
    • /
    • pp.31-37
    • /
    • 2014
  • 본 연구에서는 자료 제공을 목적으로 국내 분진폭발사고에서와 동일한 고밀도 폴리에틸렌(high-density polyethylene, HDPE ) 분진을 사용하여 열분해성과 착화에너지를 실험적으로 조사하였다. 폭발 민감도를 측정하기 위하여 시차주사열량계(differential scanning calorimeter, DSC), 열중량분석기(thermo-gravimetric analysis, TGA) 및 최소착화에너지(minimum ignition energy, MIE) 측정장치를 사용하였다. HDPE의 체적기준 평균입경은 $61.6{\mu}m$가 얻어졌으나, 입자 크기에 따른 입자 수밀도(particle number density) 분석에서는 $0.4{\sim}4{\mu}m$의 미세 입자가 98% 이상의 비율을 갖는 것으로 나타났다. TGA 및 DSC 측정결과로부터 HDPE는 $380{\sim}490^{\circ}C$의 온도 구간에서 발화가 일어날 수 있음을 알 수 있었고, MIE는 $1200{\sim}1800g/m^3$의 HDPE의 농도 범위에서 1 mJ 이하로 측정되었는데, 이는 입자 수밀도 기준에 따른 $0.4{\sim}4{\mu}m$의 미세 입자의 비율(98 %)이 매우 높았던 것이 원인으로 판단된다.

External Gelation 방법을 이용한 구형 UO3 Gel 입자 제조 (Spherical UO3 Gel Preparation Using the External Gelation Method)

  • 정경채;김연구;오승철;조문성;이영우;장종화
    • 한국세라믹학회지
    • /
    • 제42권11호
    • /
    • pp.729-736
    • /
    • 2005
  • HTGR (High Temperature Gas-cooled Reactor) is spotlighted to next generation nuclear power plant for producing the clean hydrogen gas and the electricity. In this study, the spherical $UO_3$ gel particles were prepared by the external gelation process, and the characteristics of these particles were analyzed the particle shape, composition of precipitate, and thermal decomposition characteristics with the Streoscope, FT-IR, and X-ray diffractometer. Raw material of the ADUN (Acid Deficient Uranyl Nitrate) solution, which has [$NO_3$]/[U] mole ratio = 1.75, was obtained from dissolution of the $U_{3}O_{8}$ powder with concentrated $HNO_3$, and its concentration is 3.5 M-U/l. The broth solution is prepared with the ADUN, urea, PVA, and THFA solution. The droplets of the broth solution was made through a nozzle system. From this study, we obtained the following results; 1) an externel chemical gelation process is a suitable method in the spherical $UO_3$ particle production, 2) the particle shape are changed by an urea mixing time, THFA volume, and the viscosity of the broth solution, 3) the amorphous $UO_3$ particles obtained from these experiments was converted to $U_{3}O_{8}$ and then $UO_2$ by heat treatment in hydrogen atmosphere at $600^{\circ}C$.

에어로졸 마이크로반응기에 의한 Titanium Tetraisopropoxide로부터 TiO2 나노입자 제조 (Preparation of TiO2 Nanoparticles from Titanium Tetraisopropoxide Using an Aerosol Microreactor)

  • 최재길;박균영
    • Korean Chemical Engineering Research
    • /
    • 제43권5호
    • /
    • pp.609-615
    • /
    • 2005
  • $1{\mu}l$ 정도의 미량 titanium tetraisopropoxide(TTIP)를 주사기를 사용하여 1 cc 부피의 증발관에 주입하여 기화시킨 후 질소에 의해 직경 4 mm, 길이 35 cm의 관형 에어로졸반응기로 운반하여 열분해 시킴으로써 30-300 nm 크기의 $TiO_2$ 나노입자를 제조하였으며, 반응온도 및 TTIP 증기 농도가 생성된 $TiO_2$ 입자의 형상, 크기, 결정성 등에 미치는 영향을 조사하였다. 전구체 증기 농도 1 mol%에서 반응온도를 300, 500, $700^{\circ}C$로 변화시킨 결과 반응온도가 증가함에 따라 응집체를 구성하고 있는 1차 입자 크기가 감소하였고, $700^{\circ}C$에서는 입자 크기분포가 bimodal 형태를 나타내었다. 반응온도를 $700^{\circ}C$로 유지하고 전구체 증기 농도를 1, 3.5, 7 mol%로 변화시킨 결과 전구체 증기 농도 3.5 mol% 이상에서는 1 mol%에서 관찰되었던 bimodal 분포가 사라지고 응집체 내 1차 입자들의 개수가 상대적으로 많이 증가하였다. 반응온도 및 전구체 농도가 입자의 형상, 크기분포에 미치는 이와 같은 영향들을 이전의 연구결과들과 함께 비교 분석하였다.

슬러리 기포탑 반응기에서 침강성 탄산칼슘의 모폴로지에 대한 조업변수들의 영향 (Effect of Operating Variables on the Morphology of Precipitated Calcium Carbonate in a Slurry Bubble Reactor)

  • 황정우;이융;이동현
    • 청정기술
    • /
    • 제16권2호
    • /
    • pp.124-131
    • /
    • 2010
  • 슬러리 기포탑을 이용하여 수산화칼슘 농도(0.16~0.64 wt%), 계면활성제 농도(2~16 wt%), 총 부피유량(3~6 L/min) 및 $CO_2$ 유량의 부피분율(0.3~0.6)이 탄산칼슘의 morphology, 결정구조, 입자의 크기, 입자 간의 응집화, 비표면적에 미치는 영향을 알아보았다. 실험에 사용한 반응기는 높이가 1.0 m이고 직경이 0.11m, 그리고 중앙에는 직경 4 cm인 튜브가 들어있는 슬러리 기포탑이다. 실험에 사용한 음이온 계면활성제 Dispex N40은 탄산칼슘 합성에 있어 반응 속도에 영향을 주어 반응 종결 시간을 감소시켰다. Dispex N40의 농도가 2 wt%일 때 수산화칼슘의 포화농도인 0.16 wt%에서 이산화탄소의 유량에 따른 침강성 탄산칼슘의 morphology를 살펴보면 반응 속도가 증가할수록 결정의 형태는 단일 결정으로 존재하는 입자들이 많아졌다. Dispex N40은 탄산칼슘의 crystal의 성장과 입자와 입자간의 응집 현상에 영향을 주어 탄산칼슘의 평균 입도를 변화시켰다. 또한 $0.9 L/min\;CO_2$ 유량에서 수산화칼슘의 농도가 0.64 wt%일 때 2 wt%의 계면활성제 첨가로 인해 비표면적을 $35m^2/g$에서 $44m^2/g$로 크게 증가시켰다.