• 한국컴퓨터그래픽스학회논문지
• /
• 제14권4호
• /
• pp.7-18
• /
• 2008

연기와 같은 유체의 모습을 영화나 애니메이션에서의 특수 효과에 활용하기 위해는 연기를 사실적으로 모델링하는 과정과 모델링 된 연기 내부에서의 빛의 흐름이 잘 반영된 렌더링 과정이 필요하다. 컴퓨터 그래픽스 분야에서는 연기 모델링의 사실성을 살리기 위해 물리 기반의 유체 시뮬레이션 기법을 많이 차용하고 있는데, 그동안 시뮬레이션 기법으로 주로 연구되어 온, 격자 기반의 Euler 방법과는 근본적으로 다른, 파티클 기반의 Lagrange 방법이 시뮬레이션 단계에서 얻을 수 있는 장점 때문에 최근 관심이 높아지고 있다. 연기 렌더링은 연기 모델링 방법에 종속적일 수밖에 없으므로, 결과적으로 격자 기반의 시뮬레이션 결과에 대한 렌더링 방법은 많이 연구되고 있는 데 비해, 파티클 형태로 산출된 연기 데이터에 대하여 사실적인 영상을 생성해주는 랜더링 기술에 대한 연구는 아직 부족한 상황이다. 이에, 본 논문에서는 Lagrange 기법을 적용하여 생성한 파티클 집합 형태의 연기 시뮬레이션 데이터를 사실적으로 렌더링하기 위해, 전역 조영을 위한 최신 랜더링 기술인 포톤 매핑 기법을 파티클 데이터에 맞게 변형 및 확장한 파티클맵 기법을 소개하고, 개선된 파티클템 기법을 제시하여, 기존 연구와의 차이점을 보여준다. 또한 렌더링 과정에서 효율성을 높이기 위해 볼륨 렌더링 방정식의 다중 산란 항을 미리 계산하는 광도맵이라는 방법을 제시한다.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2005년도 추계학술대회 논문집
• /
• pp.50-53
• /
• 2005

The turbulent flow around a sphere was investigated in a streamwise meridian plane using two experimental techniques: smoke-wire flow visualization in wind tunnel at Re=5,300 and PIV measurements in a circulating water channel at Re=7,400. The smoke-wire visualization shows flow separation points near an azimuthal angle of $90^{\circ}$, recirculating flow, transition from laminar to turbulent shear layer, evolving vortex roll-up and fully turbulent eddies in the sphere wake. In addition, the mean flow pattern extracted by particle tracing method in water tunnel at Re= 14,500 reveals two distinct comparable toroidal(not closed) vortices in the recirculation region. The mean velocity field measured using a PIV technique demonstrates the detailed wake configuration of close symmetric recirculation and near-wake configuration with two toroidal vortices, reversed velocity zone and vorticity contours.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2005년도 추계학술대회 논문집
• /
• pp.99-102
• /
• 2005

This study was conducted for obtaining the optimized data to build the mixer or micro fluid device as measuring the three dimensions flow field in micro mixer. To acquire the rapid diffusion on the region of low Reynolds (Re < 100), the staggered herringbone mixer using chaotic advection was selected in this case. At first, by conducting the numerical analytical virtual experiment using CFD-ACE+, three dimensions flow field in the micro mixer was estimated As this flow field was proven using defocusing particle tracing method, the behavior of micro flow with three dimensional aspects could be analyzed. Numerical analysis and flow pattern in the micro mixer by experimental verification made to be able to analyze the chaotic advection. These can be important sources for building more optimized form. Verifying the information of three dimensional flow structure, these information can be used as the data for developing and improving the $\mu$ -TAS.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1586-1588
• /
• 1994

Some interesting corona characteristics of a airgap of penpoint-to-plate with a tracing insulator paper has been investigated in a temperature and humidity controlled metal chamber. It is found that the positive and the negative carriers in the plasma region could be understood from the waterdrop traces on the paper, which indicate the bombardment by the one of electron or positive gas particle from the plasma region of near the point. It is also found that a corona discharge could be used as a means of a humidifying, since the discharge makes dispersion of watersprays from the penpoint. And the negative corona was more effective for waterspray dispersion than the positive ones.

• 대한기계학회논문집B
• /
• 제25권2호
• /
• pp.260-268
• /
• 2001

Wake structures behind two circular cylinders with different groove configurations(U and V-shape) have been investigated experimentally. The results were compared with those for the smooth cylinder having the same diameter D. The drag force, mean velocity and turbulent intensity profiles of wake behind the cylinders were measured with varying the Reynolds number in the range of Re(sub)D=8,000∼14,000. As a result, the U-shaped groove was found to reduce the drag up to 18.6%, but the V-shaped groove reduced drag force only 2.5% compared with the smooth cylinder. As the Reynolds number increases, the vortex shedding frequency becomes a little larger than that of the smooth cylinder. The visualized flow using the smoke-wire and particle tracing methods shows the flow structure qualitatively.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2013년도 제46회 KOSCO SYMPOSIUM 초록집
• /
• pp.5-8
• /
• 2013

The ignition of aluminum particles under high pressure and temperature conditions is studied. The laser ablation method is used to generate aluminum particles exposed to pressures ranging between 0.35 and 2.2 GPa. A continuous wave $CO_2$ laser is then used to heat surface of the aluminum target until ignition is achieved. We confirm ignition by a spectroscopic analysis of AlO vibronic band of 484 nm wavelength. The radiant temperature is measured with respect to various pressures for tracing of required heating energy for ignition. Then the ignition temperature is deduced from the radiant temperature using the thermal diffusion equation. The established ignition criteria for corresponding temperature and pressure can be used in the modeling of detonation behavior of heavily aluminized high explosives or solid propellants.

• Applied Science and Convergence Technology
• /
• 제26권6호
• /
• pp.189-194
• /
• 2017

Effects of gas injection scheme and rf driving current configuration in a dual turn inductively coupled plasma (ICP) system were analyzed by 3D numerical simulation using CFD-ACE+. Injected gases from a tunable gas nozzle system (TGN) having 12 horizontal and 12 vertical nozzles showed different paths to the pumping surface. The maximum velocity from the nozzle reached Mach 2.2 with 2.2 Pa of Ar. More than half of the injected gases from the right side of the TGN were found to go to the pump without touching the wafer surface by massless particle tracing method. Gases from the vertical nozzle with 45 degree slanted angle soared up to the hottest region beneath the ceramic lid between the inner and the outer rf turn of the antenna. Under reversed driving current configuration, the highest rf power absorption region were separated into the two inner islands and the four peaked donut region.

• 반도체디스플레이기술학회지
• /
• 제21권4호
• /
• pp.33-38
• /
• 2022

With an attempt to suppress the moiré phenomenon caused by the interference between the black matrix of a display panel and the metal grid of a camera, we have fabricated an anti-moiré filter using light diffusing particles (LDPs) with the average diameter of 20 ㎛. It is demonstrated that the anti-moiré filter coated on a glass substrate (370 mm × 470 mm) using a table slot-die coater reduces the moiré intensity to a great extent when the area covered by LDPs is 50%. To quantify the intensity of moiré phenomenon, we have measured the lightness ratio and found that it is reduced from 132.12 down to 105.71 by the filter. To find the optimum area covered by LDPs, we have performed ray tracing simulations using Mie scatters as a substitute for LDPs. From the simulated irradiation distribution, we have calculated the standard deviation (SD) and contrast ratio (CR) to evaluate the moiré strength. As expected, the SD and CR values decrease with increasing covered area by LDPs. However, there exists a trade-off between the transmittance of the filter and its capability of reducing the moiré intensity in determining the area covered by LDPs.

• 한국지구과학회지
• /
• 제18권6호
• /
• pp.529-539
• /
• 1997

본 연구는 2차원 순압모델을 사용하여 황해와 동중국해에서 조석잔차류와 춘 하 추 동 4계절의 해상풍에 의한 해수 순환과 이러한 순환에 의한 부유물의 이동 궤적을 추적하는데 목적을 두었다. 황해 해수 순환의 주요 외력은 조석과 바람이라고 생각되어, 조석은 $M_2$ 조석으로부터 조석잔차류를 계산하였고, 계절별 바람으로서 1월(겨울), 4월(봄), 7월(여름), 10월(가을)을 사용하였다. 조석잔차류는 한국 남 서해안과 제주도 부근과 중국 양자강 하구역 부근에서 크게 나타난다. 제주도 부근에서는 10 cm/s 이상의 최대 잔차류가 나타나며 시계방향의 순환을 보이지만 전반적으로 남해안을 따라 동향류의 경향이 있다. 또한, 중국의 연운항에서 상하이 사이의 영역에서는 한국의 남해로 향하는 순환 구조가 나타나고 있다. 바람에 의해 형성된 순환은 북풍의 성격을 띤 1월, 4월, 10월에는 해역에 시계 방향의 순환이, 남풍과 열대성 저기압의 영향을 받는 7월에는 반시계 방향의 순환이 우세했다. 이로 인하여, 한국연안에서는 7월을 제외하고는 남향류가 나타났다. 부유물은 조석 잔차류와 취송류에 의해 이동한다. 10일 동안의 이동에서는 수 십 cm/s에 달하는 취송류가 조석 잔차류보다 크게 작용했다. 그러나, 수 개월 이상의 이동에 있어서는 수 cm/s의 조석잔차류의 영향이 더 크게 나타났다.

• International Journal of Vascular Biomedical Engineering
• /
• 제2권2호
• /
• pp.27-32
• /
• 2004

The objective of the present study is to visualize the steady and pulsatile flow fields in a branching model by using a high-resolution PIV system. A bifurcated flow system was built for the experiments in the steady and pulsatile flows. Harvard pulsatile pump was used to generate the pulsatile velocity waveforms. Conifer powder as the tracing particles was added to water to visualize the flow fields. CCD cameras($1K{\times}1K$(high resolution camera) and $640{\times}480$(low resolution camera)) captured two consecutive particle images at once for the image processing of several cross sections on the flow system. The range validation method and the area interpolation method were used to obtain the final velocity vectors with high accuracy. The results of the image processing clearly showed the recirculation zones and the formation of the paired secondary flows from the distal to the apex of the branch flow in the bifurcated model. The results also indicated that the particle velocities at the inner wall moved faster than the velocities at the outer wall due to the inertial force effects and the helical motions generated in the branch flows as the flow proceeded toward the outer wall. Even though the PIV images from the high resolution camera were closer to the simulation results than the images from the low resolution camera at some locations, both results of the PIV experiments from the two cameras generally agreed quite well with the results from the computer simulations. Therefore, instead of using the expensive stereoscopic PIV or 3D PIV system, the three-dimensional flow fields in a bifurcated model could be easily and exactly investigated by this study.