• Bulletin of the Korean Chemical Society
• /
• v.35 no.12
• /
• pp.3576-3582
• /
• 2014

Zeolite-templated carbons (ZTCs), which have high specific surface area, were prepared by a conventional templating method using microporous zeolite-Y for catalyst supports in direct methanol fuel cells. The ZTCs were synthesized at different temperatures to investigate the characteristics of the surface produced and their electrochemical properties. Thereafter, Pt-Ru was deposited at different carbonization temperatures by a chemical reduction method. The crystalline and structural features were investigated using X-ray diffraction and scanning electron microscopy. The textural properties of the ZTCs were investigated by analyzing $N_2$/77 K adsorption isotherms using the Brunauer-Emmett-Teller equation, while the micro- and meso-pore size distributions were analyzed using the Barrett-Joyner-Halenda and Harvarth-Kawazoe methods, respectively. The surface morphology was characterized using transmission electron microscopy and inductively coupled plasma-mass spectrometry. The electrochemical properties of the Pt-Ru/ZTCs catalysts were also analyzed by cyclic voltammetry measurements. From the results, the ZTCs carbonized at $900^{\circ}C$ show the highest specific surface areas. In addition, ZTC900-PR led to uniform dispersion of Pt-Ru on the ZTCs, which enhanced the electro-catalytic activity of the Pt-Ru catalysts. The particle size of ZTC900-PR catalyst is about 3.4 nm, also peak current density from the CV plot is $12.5mA/cm^2$. Therefore, electro-catalytic activity of the ZTC900-PR catalyst is higher than those of ZTC1000-PR catalyst.

• Korean journal of applied entomology
• /
• v.34 no.3
• /
• pp.218-223
• /
• 1995

A nuclear polyhedrosis virus isolated from the oriental tobacco budworm larvae, Helicoverpa assulta (Guenee) was characterized by electron microscopy, SDS-PAGE, restriction endonuclease analysis and cross infectivity. The shape of a polyhedron was $1.0\mu\textrm{m}$ in average with icosahdral outline, and the virus particle was $65nm\times300nm$ in average with rod-shape. The nuclear polyhedrosis virus was contained a single nucleocapsid within a viral envelope embedded in a polyhedron. The polyhedral protein was composed of a single polypeptide with a M.W. of 31 Kd. The genome size of the virus by restriction endonuclease analysis was about 120 Kb. Among several nuclear polyhedrosis viruses, the nuclear polyhedrosis virus from Helicoverpa assulta (HaNPV) and Autographa california nuclear polyhedrosis virus (AcNPV) were infected the oriental tobacco budworm larvae.

• Applied Chemistry for Engineering
• /
• v.29 no.4
• /
• pp.425-431
• /
• 2018

Composite particles of porous silica and cerium oxide nanoparticles blocking UV/blue light were prepared through a dry coating process. Various composite particles were prepared by varying conditions such as the mixing ratio of cerium oxide and silica, and the chamber rotating speed of mechano fusion system. The surface morphology of the composite particles was observed with SEM and the composition was analyzed using X-ray fluorescence (XRF). When the cerium oxide/silica composite particles were dispersed in water, the transparency and dispersion stability of the colloidal solution were improved. In addition, the fluidity and spreadability of the particle powder were enhanced by making composite particles. These results show that cerium oxide/silica composite particles can be used as functional cosmetic ingredients for UV/blue light protection.

• Journal of the Korean Ceramic Society
• /
• v.40 no.7
• /
• pp.709-714
• /
• 2003

Eu doped $Y_2$ $O_3$ nanoparticles were prepared with the solvothermal synthesis using the ethyleneglycol solvent at 20$0^{\circ}C$ for 3-5 h and then annealed in air at 1000-140$0^{\circ}C$ for 2-4 h. The X-ray diffraction pattern of annealed crystals at 100$0^{\circ}C$ for 2 h could be indexed as pure cubic cell of $Y_2$ $O_3$ phase with lattice parameters a=10.5856 $\AA$ which is very close to the reported data (JCPDS Card File, 41-1105 a=10.6041 $\AA$). Average size of prepared phosphor particles have about 100 nm, which were spherical morphology. The phosphor particle sizes decreased and the emission intensity increased at the annealing temperature. Though PL spectrum analysis, the 3% Eu doped $Y_{2-x}$ $O_3$:E $u_{x}$ $^{3+}$(x=0.06) phosphor showed the excitation spectrum at 250 nm wavelength and the maximum emission spectrum at 611 nm wavelength.

• Journal of the Korean Ceramic Society
• /
• v.51 no.3
• /
• pp.156-161
• /
• 2014

Gallium oxide ($Ga_2O_3$) powders were synthesized using a precipitation method and a polymerized complex method. TG-DSC, SEM, and XRD were performed to investigate the phase and morphology of the $Ga_2O_3$. In situ high-temperature XRD analysis revealed the crystal structure of $Ga_2O_3$ at different temperatures. The $Ga_2O_3$ obtained using the precipitation method and polymerized complex method were generally spherical-shaped particles and their average particle size was approximately 80 nm and $1{\mu}m$, respectively. The crystal structure of the $Ga_2O_3$ prepared by the precipitation method was changed from rhombohedral to monoclinic at $700^{\circ}C$, while monoclinic $Ga_2O_3$ was obtained directly from the precursor by the polymerized complex method.

• Advances in materials Research
• /
• v.2 no.3
• /
• pp.141-153
• /
• 2013

Nanocrystalline Barium niobate ($BaNbO_3$) has been synthesized by a novel auto-igniting combustion technique. The X-Ray diffraction studies reveals that $BaNbO_3$ posses a cubic structure with lattice constant $a=4.071{\AA}$. Phase purity and structure of the nano powder are further examined using Fourier-Transform Infrared and Raman spectroscopy. The average particle size of the as prepared nano particles from the Transmission Electron Microscopy is 20 nm. The UV-Vis absorption spectra of the samples are recorded and the calculated average optical band gap is 3.74eV. The sample is sintered at an optimized temperature of $1425^{\circ}C$ for 2h and attained nearly 98% of the theoretical density. The morphology of the sintered pellet is studied with Scanning Electron Microscopy. The dielectric constant and loss factor of a well-sintered $BaNbO_3$ at 5MHz sample is found to be 32.92 and $8.09{\times}10^{-4}$ respectively, at room temperature. The temperature coefficient of dielectric constant was $-179pp/^{\circ}C$. The high dielectric constant, low loss and negative temperature coefficient of dielectric constant makes it a potential candidate for temperature sensitive dielectric applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.471.2-471.2
• /
• 2014

We demonstrate here that an improvement in precursor film density (green density) leads to a great enhancement in the photovoltaic performance of CuInSe2 (CISe) thin film solar cells fabricated with Cu-In nanoparticle precursor films via chemical solution deposition. A cold-isostatic pressing (CIP) technique was applied to uniformly compress the precursor film over the entire surface (measuring 3~4 cm2) and was found to increase its relative density (particle packing density) by ca. 20%, which resulted in an appreciable improvement in the microstructural features of the sintered CISe film in terms of lower porosity, reduced grain boundaries, and a more uniform surface morphology. The low-bandgap (Eg=1.0 eV) CISe PV devices with the CIP-treated film exhibited greatly enhanced open-circuit voltage (VOC, from 0.265 V to 0.413 V) and fill factor (FF, from 0.34 to 0.55), as compared to the control devices. As a consequence, an almost 3-fold increase in the average power conversion efficiency, 3.0 to 8.2% (with the highest value of 9.02%), was realized without an anti-reflection coating. A diode analysis revealed that the enhanced VOC and FF were essentially attributed to the reduced reverse saturation current density (j0) and diode ideality factor (n). This is associated with the suppressed recombination, likely due to the reduction in recombination sites such as grain/air surfaces (pores), inter-granular interfaces, and defective CISe/CdS junctions in the CIP-treated device. From the temperature dependences of VOC, it was confirmed that the CIP-treated devices suffer less from interface recombination.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.807-810
• /
• 2002

$GdPO_4$:Tb phosphor particles with spherical shape and high photoluminescence were prepared by spray pyrolysis. The brightness of prepared $GdPO_4$:Tb under the vacuum ultraviolet(VUV) illumination was comparable with that of the commercial $Zn_2SiO_4$:Mn phosphor particles. The photoluminescence spectra of $GdPO_4$:Tb phosphor particles had maximum peak at 547 nm, and the sharp peaks at 480 nm, 580 nm, and 620 nm. The spherical morphology of prepared $GdPO_4$:Tb particles was completely maintained even after the posttreatment up to 1100 $^{\circ}C$. When the posttreatment temperature was over 1100 $^{\circ}C$, the particles did not have the spherical shape anymore. The average particle size of $GdPO_4$:Tb phosphor particles prepared by using $(NH_4)_2HPO_4$ was changed from 0.5 to 1.9 ${\mu}m$ and its effect on the PL intensity was investigated. It was found that the optimized $GdPO_4$:Tb particles have a good excitation spectrum comparable to that of the commercial $Zn_2SiO_4$:Mn phosphor particles under the VUV illumination from 140 to 220 nm. We concluded that the $GdPO_4$:Tb phosphor particles with spherical shape prepared by spray pyrolysis is a promising candidate for a green-emitting PDP phosphor.

• Journal of Pharmaceutical Investigation
• /
• v.38 no.1
• /
• pp.63-72
• /
• 2008

Meloxicam-loaded microspheres were prepared with poly(D,L-lactic acid)(PLA) by a solvent-emulsion evaporation method. The morphology, particle size, drug loading capacity, drug entrapment efficiency (EE) and release patterns of drug were investigated in vitro. Various batches of micro spheres with different size and drug content were obtained by changing the ratio of meloxicam to $PLA^{\circ}{\AE}s$ with different molecular weight, PLA concentration in the dispersed phase and stirring rate. Meloxicam crystals on microsphere surface, which were released rapidly and could act as a loading dose, were observed with increasing drug content. The release rate was increased with increase in drug contents and decrease in the molecular weight of PLA. Microspheres prepared with smaller molecular weight produced faster drug release rate. The release rate of meloxicam for long-acting injectable delivery system in vitro, which would aid in predicting in vivo release profile, could be controlled by properly optimizing various factors affecting characteristics of microspheres. Blood concentration-time profile of meloxicam after intramuscular injection of meloxicam-loaded microspheres in rabbits showed possibility of long term application of this system in clinical settings.

• Economic and Environmental Geology
• /
• v.29 no.1
• /
• pp.87-103
• /
• 1996

The purposes of this research are to investigate the pollution level of heavy metals due to the urbanization and industrialization in the satellite cities of Seoul, and to assess the chemical species and the sources of heavy metals in highly contaminated soils and dusts. Soil and dust samples were collected from the Uijeongbu and the Koyang cities, which are northern and the northwestern satellite cities of Seoul metropolitan city, respectively. Relatively high pH values($6.3{\sim}9.9$) were found in roadside soils compared with agricultural and forest soils. Difference in pH values of soils was not identified between before and after rainy seasons. In spite of no specific pollution sources in the above cities, the contents of Cu, Pb, and Zn in soils and dusts were much higher than the world average contents. The metal levels in dusts were higher than those in soils, but the metal concentration in dusts was significantly decreased after rainy season. Pollution index was high(> 1.0) in the areas of heavy traffic, industrial complex, and city centres. There is an appreciable proportion of total Zn in exchangeable/water-acid soluble fraction. Copper is predominantly associated with reducible and oxidizable phases, whereas Pb is largely in reducible association. It is concluded that the mobility and bioavailability of metals are high in the order of Zn >> Cu > Pb, on the basis of characteristic particle morphology and chemical composition, Pb-containing particles are originated probably from the automobile exhaust, particularly in heavy traffic areas. The metallic forms and iron-oxide associated forms of Cr, Ni, Cu, Zn, and Pb can be assessed as industrial origin.