• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.10
• /
• pp.802-808
• /
• 2003

The air-side particulate fouling of the HVAC heat exchangers degrades the performance of cooling capacity, pressure drop across a heat exchanger, and indoor air quality. The purpose of this study is to investigate the fouling characteristics using accelerated particle loading system. The fouling characteristics are analyzed as functions of a dust concentration, a face velocity and a wet or dry surface condition. The pressure drop increases with increasing test operation and reaches constant asymptotic level. For the saturated condition due to particle loading, the pressure drop across the slitted finned-tube heat exchangers at the face velocity of 1 m/sec increases up to 57% and the cooling capacity decreases about 2%. The cooling capacities are not affected greatly by the presence of the fouling deposits if the thickness of the fouling deposits can not change substantially the flow pattern through the fins.

• Journal of Pharmaceutical Investigation
• /
• v.34 no.2
• /
• pp.125-130
• /
• 2004

Paclitaxel is an effective antineoplastic drug for various cancers especially ovarian and breast cancer. This study is to find the optimum condition for the preparation of nanoemulsions and to improve the stability and loading amount of paclitaxel in nanoemulsions. Nanoemulsions were prepared by modified spontaneous emulsification solvent diffusion method. It was composed of phosphatidylcholine:cholesterol:1,2-Distearoyl-sn-Glycero-3-Phosphoethanolamine-N-[Metoxy (Polyethylene glycol)-2000]:paclitaxel at a weight ratio of 5:3:1:1 and the Tween 80 as a surfactant. The particle size and the shape of nanoemulsions were measured by particle analyzer and SEM, respectively. The loading amount of paclitaxel in nanoemulsion was measured by UV-visible spectroscopy at 227 nm. The particle sizes were $80{\sim}120\;nm$ and the loading efficiency of paclitaxel was $8{\sim}39%$. The optimum conditions for the preparation of nanoemulsions were 8% w/w phospholipid, 16% w/v Tween 80 and 2% w/w paclitaxel, respectively.

• Korean Journal of Metals and Materials
• /
• v.47 no.1
• /
• pp.7-12
• /
• 2009

The detailed quantitative microstructural data on the cracking of coarse constituent particles in 7075 (T651) series wrought Al-alloys have been studied using the utility of a novel digital image processing technique, where the particle cracks are generated due to monotonic loading. The microstructural parameters such as number density, volume fraction, size distribution, first nearest neighbor distribution, and two-point correlation function have been quantitatively characterized using the developed technique and such data are very useful to verify and study the theoretical models for the damage evolution and fracture of Al-alloys. The data suggests useful relationships for damage modeling such as a linear relationship between particle cracking and strain exists for the uniaxial tensile loading condition, where the larger particles crack preferentially.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.360.1-360.1
• /
• 2016

Hydroxyapatite (Ca10(PO4)6(OH)2, HAP) particles have attracted a great deal of attention in biomedical fields due to their good biocompatibility, bioactivity and fairly broad applications as drug delivery, dental implant, bone cement, and etc. Thus, many researchers have made an effort to add new functionalities such as luminescence, drug delivery, and bone regeneration properties up to HAP powders by controlling their nanostructure as well as composition. In this research, the mesoporous strontium substituted HAP (Sr-HAP) microspheres were synthesized using a hydrothermal method. In this synthesis, aspartic acid monomers were utilized to form microsphere by controlling surface energy of HAP particles and Sr ions were substituted into Ca ion sites, which induced luminescence property in HAP powders. Moreover, the change in the amount of Sr substitution was found to influence the particle size, morphology, and concurrently surface area, which led to changing drug loading as well as drug release property. The amount of Sr influences the morphology, luminescent properties, particle size, surface area cell viability and drug loading property, which are investigated by SEM, TEM, XRD, FTIR, BET, XPS and in vitro test such as MTT assay and drug release test. In particular, the multifunctional Sr-HAP with molar ratios of 0.25 (Sr/(Ca+Sr)) possessed the strongest luminescent property as well as the superior drug loading and sustained release properties that were correspondent with large surface area and pore size. Our study indicates that the fabricated multifunctional Sr-HAP microspheres are quite useful for bone regeneration and drug delivery.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.214-224
• /
• 1990

A "two-fluid" model using thermal eddy diffusivity concept and Lumley's drag reduction theory, is proposed to analyze heat transfer of the turbulent dilute gas-particle flow in a vertical pipe with constant wall heat flux. The thermal eddy diffusivity is derived to be a function of the ratio of the heat capacity-density products .rho. over bar $C_{p}$ of the gaseous phase and the particulate phase and also of the ratio of thermal relaxation time scale to that of turbulence. The Lumley's theory dictates the variation of the viscous sublayer thickness depending on the particle loading ratio Z and the relative particle size $d_{p}$/D. At low loading ratio, the size of viscous sublayer thickness is important for suspension heat transfer, while at higher loading, the effect of the ratio .rho. $_{p}$ over bar $C_{p}$$_{p}$/ .rho. $_{f}$ over bar $C_{p}$$_{f}$ is dominant. The major cause of decrease in the suspension Nusselt number at lower loading ratio is found to be due to the increase of the viscous sublayer thickness caused by the suppression of turbulence near the wall by the presence of solid particles. Predicted Nusselt numbers using the present model are in satisfactory agreements with available experimental data both in pipe entrance and the fully developed regions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.5
• /
• pp.386-392
• /
• 2020

In this study, the drift current characteristics of charged particles are analyzed for panels fabricated by varying the waveform biasing of the active particle loading method (APLM), which is a method driven by the electrophoretic principle of loading charged particles into a cell of a barrier rib-type electronic paper. We prepare 3 panels using APLM and 1 panel without APLM. The waveform of APLM uses square wave and ramp wave, and the step voltage wave is applied to the driving voltage. The drift currents measured from the square wave and ramp wave with the same period applied by APLM are 4.872 µC and 5.464 µC, respectively, and the ramp wave is shown to be relatively advantageous for loading charged particles that have a large q/m. The time-current curve results confirm that the abrupt movement of charged particles is occurring. When the step form wave signal with a short time of 1s is first applied, initial large movement of the charged particles is confirmed to occur in all samples, which is understood as the effect of applying the voltage necessary to remove the imaging force. The results of this study are expected to improve the loading of charged particles into the electronic paper cell, driven by the electrophoretic principle and optimization of the driving conditions.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.5
• /
• pp.1947-1955
• /
• 2013

The purpose of this paper is to present an photoelasticity technique for measuring the displacement and stress distribution in particle assembly subjected to shallow foundation loading. Photoelastic measurement technique was employed to visualize the force transmission of a particle assembly. A model assembly bounded by a steel frame was built by stacking bi-dimensional circular particles made of polycarbonate elastomer. Each particle was coated by a thin photoelastic sheet so that the force transmission represented by bright light stripes can be visualized. In a contacted particle, both magnitude and orientation of principal stress difference can also be measured via the photoelasticity technique. The different distributions of the contact stresses at the initial loading and near the failure were quantitatively compared. The photoelastic patterns and displacement fields observed in the pre-failure state disappears immediately after the buckling of confined force chains.

• Journal of Energy Engineering
• /
• v.5 no.2
• /
• pp.131-137
• /
• 1996

Typical size distribution of emission particulates is bi-modal in shape with particles in the fine mode (< 2.0 $\mu\textrm{m}$) and the coarse mode. An experimental study of pressure drop across the industrial gas cleaning filters has been conducted using particle mixture of fine alumina and coarse Arizona dusts with a rotating aerosol disperser to generate the bi-modal test aerosol. Pressure drop increased linearly with increasing mass loading. The pressure drop was found to be strongly dependent upon the mass ratio of fine to coarse particles. The smaller the mass ratio of fine to coarse particles and the higher face velocity are, the faster pressure drop rises. The fine particles and the greater inertia of the particle moving fast would cause a denser cake formation on the filter surface, resulting in a greater specific resistance to the gas flow.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.812-815
• /
• 2007

Computational simulation has been performed to design the filtration system for Korea model IGCC demonstration plant. The filtration system for optimal design has four effective filters corresponding to the clusters composed of a group of ceramic candle filters. It was analyzed how the different entrance geometry influences the flow field and the particle behavior in the filtration system. The particle loading is minimum when the gas mixed with particles flows into the filter vessel with a shroud tube through a tangential inlet. However, the particle loading is maximum when the gas with particles enters the filter vessel through a normal inlet which a entrance tube extended from. By controling adequately both conditions of inflow, the filtration system can be operated optimally to prolong the filter life-time and to save the energy for cleaning filters.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.97-103
• /
• 1998

The flow structure of particles for two different injectors has been investigated experimentally by means of a Phase Doppler Particle Analyzer(PDPA). Two injectors used in the present study are the pipe and contraction nozzle. Particles of 0.8${\mu}{\textrm}{m}$, 30${\mu}{\textrm}{m}$, 60 ${\mu}{\textrm}{m}$, and 100${\mu}{\textrm}{m}$ diameter were injected with a constant mass loading ratio of 0.01 and a Reynolds number of 13200. The initial mean velocity and turbulent intensity of particle are strongly influenced by the particle size and the injector geometry. The flow angles of particle at nozzle exit are sensitive to the particle size rather than the injector geometry.