• Journal of the Korean Applied Science and Technology
• /
• v.37 no.3
• /
• pp.484-495
• /
• 2020

This study is a mixed surfactant (MimicLipid-MSM1000) that forms the same structure as that of the stratum corneum, sucrose distearate, polyglyceryl-2 dioleate, fermented squalane, ergosterol, 10-hydroxystearic acid, mixture consisting of was synthesized. When using 2~5 wt% of this mixed surfactant, it was possible to make an artificial skin mimetic that forms a multi-layer lamellar structure of 5~30 layers. An emulsion was prepared using this mixed surfactant, and a multi-layered lamellar phase was formed and analyzed mechanically. The appearance of this surfactant was a light brown hard wax, the hydrophilic lipophilic balance (HLB) was 12.53, the critical parameter value was 0.987, and the acid value was 0.13. Stability according to pH change was also stable in acidic (3.8), neutral (7.2) and alkaline (10.8). The particle size of the liquid crystal was found to be the most stable maltese cross lamellar crystalline droplet at 5~25mm. The size of the emulsified particles according to the change in the speed of the homo agitator is 2500 rpm (17.9mm±2.6mm), 3500rpm (12.5mm±2.1mm), 4500rpm (6.2mm±1.8mm) particles were formed. Liquid crystal forming particles were observed through a polarization microscope, and the formation structure of the liquid crystal was precisely analyzed with a scanning electron microscope (cryo-SEM). As an application field, it is expected that it will be widely applicable to the development of various prescriptions, such as various skin care cosmetics, makeup care cosmetics, and scalp protection cosmetics, by using a skin-mimicking surfactant.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.32 no.2
• /
• pp.121-126
• /
• 1999

In order to degrade chitin by enzymatic hydrolysis, it is required from screening highly active deacetylase. To this end, we examined three fungal strains and it turned out that Mucor rouxii produced highly active deacetylase, this enzyme exhibited the highest enzymatic activity against colloidal chitin. The conditions for growing Mucor rouxii are as follows; the effective carbon source, nitrogen source, adequate initial pH, temperature and incubation time were $2\%$ glucose, $1.33\%$ yeast extract, $0.66\%$ pepton, 4.5, $25{\pm}2^{\circ}C$ and 48hr, respectively. The optimum pH and temperature for purified enzyme activity were 5.5 and $40^{\circ}C$, respectively. The purified enzyme was stable at pH ranging from 4.5 to 5.5. However, the enzyme activity was decreased to less than $50\%$ at pH blow 45 and above 7.5. At temperatures above $50^{\circ}C$, the enzyme activity was decreased remarkably. The enzyme was inhibited by LiC1, $HgCl_2$, and $BaCl_2$, but stimulated by $CaCl_2$ and $ZnC1_2$, The activity of purified enzyme was increased by L-cysteine and 2-mercaptoethanol, while decreased by O-phenanthroline, p-CMB, EDTA, and iodoacetate. The $K_m$ and the $V_{max}$ value of purified enzyme were $1.2\%$ and 59.5 U/mg, respectively. The deacetylation activity of purified enzyme was not detected at optimal reaction condition when chitin particle suspension was used.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.3
• /
• pp.332-344
• /
• 1996

The vertical profiles of the natural $^{210}Po,\;^{210}Pb\;and\;^{234}Th$, activities were measured at the upper 150 m or 200 m of water column from west-east intersection in the east-southern coastal area of the Korea Peninsula during the period from 26 to 29 April 1994 to compare the removal rates (residence time) and removal processes for $^{210}Po\;and\;^{234}Th$. At the inshore stations, the $^{210}Po$ activity was generally higher in the thermocline and its under layer than in the surface mixed layer, while represented the reversed pattern at the offshore stations. However, the $^{210}Pb$ activity decreased generally with depth. Also, the activity of $^{210}Po$ relative to its parent $^{210}Pb$ was deficient in the water column above the main thermocline, but was slightly excess or close to equilibrium in the thermocline and its under layer. The vertical profiles for the activity of $^{210}Pb$ relative to its parent $^{226}Ra$ showed the reversed pattern with the vertical variation of $^{210}Po$ excess (or deficiency). The $^{234}Th$ activity was significantly lower in the surface mixed layer and thermocline than in the deeper layer. The residence time of $^{210}Po$ ranged from 1 to 4 years at the five stations except station E8 that showed yet long residence time (approximately 10 years). The long residence time at the station E8 may resulted from the thicker surface mixed layer and subsequent the vertical mixing of $^{210}Po$ which was recycled in the lower surface mixed layer compared to at the other stations. Also, the residence time of $^{210}Po$ was shorter at the inshore stations than at the offshore stations. However, the residence time of $^{234}Th$ ranged from 52 to 74 days at all station without the significant variation, was very much shorter relative to the residence time of $^{210}Po$. The correlation between the removal rate of dissolved $^{234}Th$ and the concentration of total suspended matter (TSM) was generally positive. Therefore, it seems that the major route of the removal mechanism of $^{234}Th$ from seawater in the surface mixed layer is via adsorption onto suspended particle surfaces (most likely inorganic particles) and subsequent settling to the bottom layer. Between the removal rate of dissolved $^{210}Po$ and the concentration of chlorophyll-a was positively good correlation. Consequently, most likely the removal of $^{210}Po$ may be occurred by uptake to organisms (mainly such as planktonic debris or fecal pellets) and subsequent settling.

• Restorative Dentistry and Endodontics
• /
• v.25 no.3
• /
• pp.399-406
• /
• 2000

The effect of inlay surface treatment on bonding was investigated when resin inlay was bonded to resin-modified glass-ionomer base with resin cement. For the preparation of glass-ionomer base, resin-modified glass-ionomer cement (Fuji II LC, GC Co., Japan) was filled in class I cavities of 7mm in diameter and 2mm in depth made in plastic molds. Eighty eight resin inlay specimens were made with Charisma$^{(R)}$ (Kulzer, Germany) and then randomly assigned to the four different surface treatment conditions: Group I, $50{\mu}m$ aluminium oxide sandblasting and silane treatment ; Group II, silane treatment alone ; Group III, sandblasting alone, and Group IV (control), no surface treatment. After a dentin bonding agent with primer (One-Step$^{TM}$, Bisco Inc., IL., U.S.A.) was applied to bonding surface of resin inlay and base, resin inlay were cemented to glass-ionomer base with a resin cement (Choice$^{TM}$, Bisco Inc., IL., U.S.A.). Shear bond strengths of each specimens were measured using Instron universal testing machine (4202 Instron, lnstron Co., U.S.A.) and fractured surfaces were examined under the stereoscope. Statistical analysis was done with one-way ANOVA and Dunkan's multiple range test. The results were as follows: 1. Sandblasting and silane treatment provided the greatest bond strength(10.56${\pm}$1.95 MPa), and showed a significantly greater bond strength than sandblasting alone or no treatment (p<0.05). 2. Silane treatment provided a significantly greater bond strength(9.77${\pm}$2.04 MPa) than sandblasting alone or no treatment (p<0.05). However, there was no significant difference in bond strength between sandblasting treatment and silane one (p>0.05). 3. Sandblasting alone provided no significant difference in bond strength from no treatment (p>0.05). 4. Stereoscopic examination of fractured surface showed that sandblasting and silane treatment or silane treatment alone had more cohesive failure mode than adhesive failure mode. 5. In relationship between shear bond strength and failure mode, cohesive failure occurred more frequently as bond strength increased.

• Restorative Dentistry and Endodontics
• /
• v.32 no.6
• /
• pp.498-513
• /
• 2007

Since it was reported that incipient enamel caries can be recovered, previous studies have quantitatively evaluated that enamel artificial caries have been, remineralized with fluoride showing simultaneously the increase of width of surface layer and the decrease of width of the body of legion. There is, however, little report which showed that remineralization could occur without fluoride. In addition, the observations on the change of hydroxyapatite crystals also have been scarcely seen. In this study, enamel caries in intact premolars or molars was induced by using lactic acidulated buffering solutions over 2 days. Then decalcified specimens were remineralized by seven groups of solutions using different degree of saturation(0.212, 0.239, 0.301, 0.355) and different pH(5.0, 5.5, 6.0) over 10 days. A qualitative comparison to changes of hydroxyapatite crystals after fracturing teeth was made under SEM(scanning electron microscopy) and AFM(atomic force microscopy). The results were as follows: 1. The size of hydroxyapatite crystals in demineralized area was smaller than the normal ones. While the space among crystals was expanded, it was observed that crystals are arranged irregularly. 2. In remineralized enamel area, the enlarged crystals with various shape were observed when the crystals were fused and new small crystals in intercrystalline spaces were deposited. 3. Group 3 and 4 with higher degree of saturation at same pH showed the formation of large clusters by aggregation of small crystals from the surface layer to the lesion body than group 1 and 2 with relatively low degree of saturation at same pH did. Especially group 4 showed complete remineralization to the body of lesions. Group 5 and 6 with lower pH at similar degree of saturation showed remineralization to the body of lesions while group 7 didn't show it. Unlike in Group 3 and 4, Group 5 and 6 showed that each particle was densely distributed with clear appearance rather than crystals form clusters together.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.101-111
• /
• 2016

It is possible that aggregates add on to geopolymer based fly ash to mix mortar and concrete like cement. This is necessary to evaluate mineral composition, particle shape, surface, size distribution, density and absorption ratio for fine aggregates due to few detailed research to examine influence of fine aggregates properties on unhardened geopolymer concrete. In this research, used two different fine aggregates, Jumunjin sand(having quartz, mica, feldspar, pyroxene in mineral composition, more than 96% of total size between -0.60 and +0.30mm, angular shape and rough surface) and ISO sand(having almost all quartz in mineral composition, more than 51% size between -1.40 and +0.60mm, simultaneously varied size distribution, spherical shape and smooth surface). After an experimental result of the varied ratio of Si/Al=1.0-4.1 geopolymer paste, mix proportion respectively applied Si/Al=1.5 having the highest compressive strength to mortar and Si/Al=3.5 having the highest consistency to concrete. Geopolymer mortar by mixing with Jumunjin and ISO sand in varied range of 20-50wt.% showed flow size increase between 69.5 and 112.0mm, between 70.5 and 126.0mm respectively. Geopolymer concrete at an addition of 77wt.% of total aggregates ratio showed that average compressive strength was 32MPa and the consistency was favorable to molding. Since ISO sand observing varied size distribution, spherical shape, smooth surface, low absorption ratio resulted in advantageous properties on consistency of geopolymer, geopolymer concrete can be suitable for using the fine aggregates similar to ISO sand.

• Journal of Technologic Dentistry
• /
• v.33 no.1
• /
• pp.93-102
• /
• 2011

Purpose: The study aimed to evaluate working environment for dental technician by measuring dust level, ventilation conditions and the use of personal protective equipment and to provide basic information required to improve working environment and develop health education programs for dental technician. Methods: A total of 240 dental technician who are registered with the Daegu Association of Dental technician and working at 34 dental laboratories participated in the study. And the dust level was measured at 21 different spots in 16 dental laboratories out of 34. Results: Of 34 dental laboratories, 31 (91.2%) were equipped with a ventilator, but the remaining 3 (8.8%) did not have a ventilator. By the number of ventilator, 1 to 3 ventilators were found in 22 dental laboratories (71.0%), 4 to 6 ventilators were in 7 laboratories (22.5%) and more than 7 ventilators in 2 laboratories(6.5%). According to the frequence of changing filters in dust collector, 20 dental laboratories (58.9%) changed filters every four weeks, 10 laboratories (29.4%) changed them every six weeks and 4 laboratories (11.7%) changed them every eight weeks. Of total respondents, 114 (61.3%) said they wore a mask all the time while working, 56 (29.6%) said they frequently wore a mask, 19 (10.1%) said they did not wear a mask. As for the type of masks, 159 (84.1%) used a disposable mask, 25 (13.2%) used a cotton mask and 5 (2.7%) used an anti-dust mask. For dust sat on their outfits while working, 102 (54.0%) shook their uniforms inside workplace to keep dust off the uniforms, 64 (33.9%) did not anything until they wash their uniforms and 23 (12.1%) shook their uniforms outside workplace to keep dust off the uniforms. Of total respondents, 182 (96.3%) had a particle in their eyes while carrying out grinding work. Based on the measurement of floating dust at workplace, 3 dental laboratories showed dust concentration exceeding the minimum level of 10 mg/$m^3$ allowed under the permit for environment. Of those, 1 laboratory had the dust concentration that was more than 1.5 times higher than the minimum level. Dust concentration was higher in laboratories that used a dust collector with 0.5 horse power and changed filters more than 3 weeks ago. Dust comprised of nickel (more than 70%), chrome (9%) and others. The mean chrome concentration was more than twice higher than the minimum permissible level of 0.5 mg/$m^3$. There were two laboratories that showed chrome concentration exceeding the level of 0.4 mg/$m^3$. Like dust concentration, chrome level was higher in laboratories that used a dust collector with 0.5 horse power and changed filters more than 3 weeks ago. There were six laboratories that had nickel concentration exceeding the minimum permissible level of 1 mg/$m^3$. Of those, one laboratory had nickel concentration that was more than three times higher than the minimum permissible level. Nickel concentration was also higher in laboratories that used a dust collector with 0.5 horse power and changed filters more than 3 weeks ago. Conclusion: It is not likely that heavy metal concentrations found in the study constitute respiratory dust. It is however necessary for health of dental technician to apply the Industrial Safety and Healthy Law to dental laboratories and make recommendations for the use of personal protective equipment, installation of a proper number of ventilators, more frequent change of filters in dust collector and improved ventilation for polishing work. At the same time, dental technician need education on how to use personal protective equipment and how to efficiently remove dust from their uniforms.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.4
• /
• pp.288-294
• /
• 2007

The LSCF cathode far Solid Oxide Fuel Cell was investigated to develop high performance unit cell at intermediate temperature by modified oxalate method with different electrolytes and different pH. The LSCF powders employed La, Sr, Co and Fe oxides, oxalic acid, ethanol and $NH_4OH$ solution were synthesized with pH controlled as 2, 6, 7, 8, 9 and 10 at $80^{\circ}C$ Single crystalline phase was obtained from pH $2{\sim}9$. on the other hand, $La_2O_3$ appeared from pH 10. Very fine powder with particle size of 50 nm was obtained at calcination temperature of $800^{\circ}C$ for 4 hours. LSCF cathode synthesized at pH 7 showed the highest electric conductivity in the temperature range of $600^{\circ}C$ to $900^{\circ}C$ its value was 950 S/cm at $900^{\circ}C$ Under same synthesis conditions, polarization resistance of each LSCF cathode was changed with different calcination temperatures. As-prepared powder presented 2.52, 1.54 and $2.58\;{\Omega}$ at $600^{\circ}C$ with ScSZ, 8Y-YSZ and GDC as its electrolyte respectively after calcination at $800^{\circ}C$ for 4 hours.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.8
• /
• pp.1270-1277
• /
• 2014

This study investigated the quality characteristics of instant rice noodles manufactured with broken rice flour as an application of rice-processed products. We examined the physicochemical characteristics of common rice flour (CRF), broken rice flour (BRF), and CRF mixed with BRF (CBRF). Futhermore, instant rice noodles were manufactured with these three types of rice flour, and their quality and sensory characteristics were also investigated. Damaged starch content and water-binding capacity of rice flour were highest in BRF. Particle size of rice flour was significantly different among the three types. RVA pasting viscosities of BRF and CBRF were higher than that of CRF. Volume after cooking of instant rice noodles increased in rice noodles made with broken rice flour (BRN). Turbidity and cooking loss of BRN were higher than those of common rice noodles (CON). For texture properties, CON displayed the highest hardness, adhesiveness, and chewiness. In the sensory evaluation, springiness and overall acceptability values of CON were significantly higher than those of other rice noodle types (BRN and CBRN). In conclusion, BRN showed increased cooking loss and turbidity with reduced texture and overall acceptability values. The results of this study suggest that added amount of CRF may significantly increase the overall quality of instant rice noodles prepared with BRF.

• The Korean Journal of Air & Space Law and Policy
• /
• v.26 no.2
• /
• pp.203-237
• /
• 2011

Since USSR successfully launched its satellite "Sputnik"in 1957, many countries including US and USSR began military use of space, and engaged in arms race in space, which is against spirit and ideals of peaceful use of space as common heritage of mankind stipulated in many treaties such as Outer Space Treaty. With worsening Cold War between East and Western Bloc, this military use of space and arms race in space has been intensifying. Regarding the ideals of peaceful use of space, it is interpreted that military use of space is possible unless it does not have the purpose of aggression. The military use of space may have diverse forms such as attacking satellites in space, or attacking from satellites, making use of present and future technologies available which should include the use of nuclear and kinetic/hyper-speed weapons, laser, particle beams, near explosion, disturbance weapons in different directions (i.e., surface to space, space to space, and space to surface). Arms control is being implemented by the efforts of many countries in different formalities including legislature of international treaties under the auspices of UNCOPUOS and prohibition of weapons of mass destruction. Taking outstanding examples aiming at arms control by international community, there are confidence building measures (CBM), strengthening implementation of existing treaties, partial ban of nuclear tests, countryand regional approach, comprehensive approach and measures having legally binding force. While U.S. has surpassed other countries concerned in the area of military useof space, it withdrew from OST in early 2000s, thereby raising concern of international community. It requires concerted efforts of cooperationand implementation by international society to make sure peace of mankind and environmental conservation through arms control in space. Observing de facto possession of nuclear weapons by North Korea following series of nuclear tests and launching satellites, and efforts of launching rockets by South Korea, it is strongly needed for both countries to take part in arms control efforts by international community.