• 한국지진공학회논문집
• /
• 제20권1호
• /
• pp.1-8
• /
• 2016

Permanent deformation plays a key role in performance based earthquake resistant design. In order to estimate permanent deformation after earthquake, it is essential to secure reliable response history analysis(RHA) as well as earthquake scenario. This study focuses on permanent deformation of an inverted T-type wall under earthquake. The study is composed of two separate parts. The first one is on the verification of RHA and the second one is on an effect of input earthquake motion. The former is discussed in this paper and the latter in the companion paper. The verification is conducted via geotechnical dynamic centrifuge test in prototype scale. Response of wall stem, ground motions behind the wall obtained from RHA matched pretty well with physical test performed under centrifugal acceleration of 50g. The rigorously verified RHA is used for parametric study to investigate an effect of input earthquake motion selection in the companion paper.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.256-261
• /
• 2016

In this paper, Shape optimal design for a chair with 4 legs and 2 stretchers consisting of stainless steel was conducted. The shape was transformed by identifying stress and deformation for the part of leg and stretcher. In addition, load condition and mesh was designed using Hypermesh. The stress analysis was carried out using CSD_Elast that is one of EDISON program. In seat test, Maximum equivalent stress was showed at the contact part between seat and legs. As a result, a leg cross-section with rectangular and arch was designed. And optimal height of stretcher was found to reduce a deformation. Also, maximum deformation was reduced by designing a stretcher with ellipse cross-section. So, Optimal chair having 4 legs with rectangular cross section and 2 stretchers with ellipse cross section was shown to satisfy the safety ratio.

• Design & Manufacturing
• /
• 제17권1호
• /
• pp.13-19
• /
• 2023

Blanking processing is one of the shear processing method in which the cut part becomes a product and piercing processing is a press molding process in which the cut part is discarded as a scrap. The shear angle of the punch used for blanking is determined by conditions such as the characteristics of the shear material, shear thickness and shear length. The shear angle of a punch is an important factor in determining the size of the shear load, the life of the shear punch, the deformation of the shear product and the quality of burrs In this study, blanking punches applied with four types of shear angles (i.e., 0°, 0°23", 0°46", 0°69") to the blanking punches of bracket products used in practical work were manufactured and tested. In the blanking experiment, the remaining variables except for the shear angle were the same. Experiments show that the product has the least amount of deformation in blanking punches with a shear angle equal to the material thickness, i.e., 0°46"..

• 열처리공학회지
• /
• 제35권2호
• /
• pp.66-73
• /
• 2022

Partial-hardened hot stamping has been well known to be very effective to absorb more energy in automotive lateral crash. Hardness distribution and dimensional change after partial-hardened hot stamping have been studied to find out effect of thermal deformation of the heated hot stamping die on dimensional accuracy of automotive center pillar. Soft zone of commercial center pillar showed 275~345 in Vickers hardness, indicating bigger non-uniformity which resulted from thermal deformation of heated die. Dimensional changes in soft zone of the commercial center pillar measured by three dimensional scanner were much bigger than that in hard zone. It has been found that hot stamping die compensation considering thermal deformation in soft zone causes a significant decrease in hardness deviation in the soft zone, corresponding to 20 percent of commercial center pillar and subsequently leads to much higher dimensional accuracy.

• 한국기계가공학회지
• /
• 제6권2호
• /
• pp.3-8
• /
• 2007

Nonlinear property and contact matter are analyzed about the pipe applied with internal pressure through this study. The weakest part and its safety can be examined. Maximum equivalent stress is shown at the contact surface between bolt and nut. The value of contact stress with the pressure of 12MPa is increased 1.4 times as large as that with no pressure. The maximum contact pressure is shown at the clamp corner of the external surface on pipe. The value of contact pressure with the pressure of 12MPa is increased 1.4 times as large as that with no pressure. The radial deformation with no pressure is also increased greatly at the middle part of internal surface on pipe. But this maximum deformation on pipe with the pressure of 12MPa is shown at the part far away the support of pipe. This value is increased 5.7 times as large as that value with no pressure. As contact status, the sticking occurs most at the external surface of pipe. It also tends to occur at the contact surface between bolt and nut. At the external surface of pipe, the sticking in case of the pressure of 12MPa occurs more than that in case of no pressure.

• 한국산학기술학회논문지
• /
• 제11권10호
• /
• pp.3641-3646
• /
• 2010

본 연구에서는 타워크레인의 지브 끝에 하중을 주고 마스트에 모멘트를 주어 그에 따른 변형 해석을 수행하여 다음과 같은 해석 결과를 보았다. 지브를 지지하고 있는 와이어의 끝 부분에서 응력이나 변형이 가장 많이 일어남을 알 수 있었고 하중이 작용하는 지브의 끝 부분에서 변형이 많이 일어나고 마스트 밑 부분은 변형이 없는 것으로 나타났다. 또한 마스트의 윗부분에서 가장 수명이 짧아져서 가장 취약함을 알 수 있었다. 이러한 크레인의 구조 해석결과를 통하여 그 안전 설계 및 내구성을 향상할 수 있다고 사료된다.

• Tribology and Lubricants
• /
• 제30권2호
• /
• pp.116-123
• /
• 2014

The objective of this study is to model and simulate the nonlinear lubrication performance of the sliding part between the piston and cylinder wall in a hydrostatic swash-plate-type axial piston pump. A numerical algorithm is developed that facilitates simultaneous calculation of the rotating body motion and fluid film pressure to observe the fluid film geometry and power loss. It is assumed that solid asperity contact, so-called mixed lubrication in this study, invariably occurs in the swash-plate-type axial piston pump, which produces a higher lateral moment on the pistons than other types of hydrostatic machines. Two comparative mixed lubrication models, rigid and elastic, are used to determine the reaction force and sliding friction. The rigid model does not allow any elastic deformation in the partial lubrication area. The patch shapes, reactive forces, and virtual local elastic deformation in the partial lubrication area are obtained in the elastic contact model using a simple Hertz contact theory. The calculation results show that a higher reaction force and friction loss are obtained in the rigid model, indicating that solid deformation is a significant factor on the lubrication characteristics of the reciprocating piston part.

• 암석학회지
• /
• 제12권3호
• /
• pp.101-109
• /
• 2003

석영의 파동소광은 암석의 변형도를 나타낼 수 있는 좋은 지표로서 사용할 수 있다. 암석의 변형도를 결정하기 위해 석영의 파동소광강도(IWE)를 편광현미경, 디지털 카메라, NIH Image 프로그램으로 측정하였다. 이러한 방법을 이용하여 흑운모화강암(Gb), 석류석흑운모화강암(Ggb) 그리고 복운모화강암(Gtm)으로 구성되어 있는 포천-기산리 일대의 쥬라기의 화강암류의 변형정도를 측정하였다. 본 연구에서는 크게 포천읍을 기준으로 서부에 분포하는 Gb와 동부에 분포하는 Ggb에서 파동소광의 강도 측정이 이루어 졌다. 측정 결과 Gb는 D2 이하의 낮은 변형도가 나타났고, Ggb는 D3이상의 고변형이 나타나, 전반적으로 조사지역의 북서부에서 남동부로 갈수록 변형도가 증가하는 양상을 보여주었다. 이는 1:250,000지질도에 기재된 Ggb상을 관통하는 단층에 의한 영향으로 사료된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.561-562
• /
• 2012

• 한국기계가공학회지
• /
• 제9권6호
• /
• pp.59-65
• /
• 2010

This study deals with the characteristic of refrigerant for heat-treatment deformation control of SCM415 steel. The control of heat-treatment deformation must need the progress of production parts for an industry machine. Most of the deformation is occurred on unequal cooling. The unequal cooling is occurred by a property of quenching refrigeration. When a heated metal is deposited in the refrigeration, the cooling speed is so slow in early period of cooling because of occurring a steam-curtain. After more cooling, the steam-curtain is destroyed. In this progress, the cooling speed is very fast. The object of this study is to control the deformation of heat-treatment for the part of the industry machine by improving the conditions of quenching. The cooling curves and cooling rates of water, oil and polymer solution are obtained and illustrated. From the characteristics of the quenching refrigerant, the effects of heat-treatments on the thermal deformation and fatigue strength are also investigated.