• Asian-Australasian Journal of Animal Sciences
• /
• v.20 no.2
• /
• pp.208-213
• /
• 2007

The objective of the experiment was to determine the optimum cultural [moisture levels (55, 60 and 70%), days of fermentation (7, 14 and 21), temperature (25 and $35^{\circ}C$) of incubation)] and nutritional parameters (urea addition (0 and 2%) and variable levels of single super phosphate (0.25 and 0.50% SSP)) for bio-processing of the mustard (Brassica campestris) straw (MS) under solid-state fermentation (SSF) system. The performance of SSF was assessed in terms of favorable changes in cell wall constituents, protein content and in vitro DM digestibility of the MS. Sorghum based inoculum (seed culture) of Ganoderma lucidum to treat the MS was prepared. The 50 g DM of MS taken in autoclavable polypropylene bags was mixed with a pre-calculated amount of water and the particular nutrient in the straw to attained the desired levels of water and nutrient concentration in the substrate. A significant progressive increase in biodegradation of DM (p<0.001), NDF (p<0.01) and ADF (p<0.05) was observed with increasing levels of moisture. Among the cell wall constituents the loss of ADF fraction was greatest compared to that of NDF. The loss of DM increased progressively as the fermentation proceeded and maximum DM losses occurred at 28 days after incubation. The protein content of the treated MS samples increased linearly up to the day $21^{th}$ of the incubation and thereafter declined at day $28^{th}$, whereas the improvement in in vitro DM digestibility were apparent only up to the day $14^{th}$ of the incubation under SSF and there after it declined. The acid detergent lignin (ADL) degradation was slower during the first 7 days of SSF and thereafter increased progressively and maximum ADL losses were observed at the day $28^{th}$ of the SSF. The biodegradation of DM and ADL was not affected by the variation in incubation temperature. Addition of urea was found to have inhibitory effect on fungal growth. The effect of both the levels (0.25 and 0.50) of SSP addition in the substrate, on DM, NDF, ADF, cellulose and ADL biodegradation was similar. Similarly, the protein content and the in vitro DM digestibility remain unaffected affected due to variable levels of the SSP inclusion in the substrate. From the results it may be concluded that the incubation of MS with 60 percent moisture for 21 days at $35^{\circ}C$ with 0.25 percent SSP was most suitable for MS treatment with Ganoderma lucidum. Maximum delignification, enrichment in the protein content and improvement in in vitro DM digestibility were achieved by adopting this protocol of bioprocessing of MS.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.3
• /
• pp.326-332
• /
• 2011

The authors examined the effects of operating parameters on the $H_2$ production by dark fermentation of the wastewater generated from food waste recycling facilities, in short "food waste wastewater (FWW)". Central composite design based response surface methodology was applied to analyze the effect of initial pH (5.5-8.5) and substrate concentration (2-20 g Carbo. COD/L) on $H_2$ production. The experiment was conducted under mesophilic ($35^{\circ}C$) condition and a heat-treated ($90^{\circ}C$ for 20min)anaerobic digester sludge was used as a seeding source. Although there was a little difference in carbohydrate removal, $H_2$ yield was largely affected by the experimental conditions, from 0.38 to 1.77 mol $H_2$/mol $hexose_{added}$. By applying regression analysis, $H_2$ yield was well fitted based on the coded value to a second order polynomial equation (p = 0.0243): Y = $1.78-0.17X_1+0.30X_2+0.37X_1X_2-0.29X_1{^2}-0.35X_2{^2}$, where $X_1$, $X_2$, and Y are pH, substrate concentration (g Carbo. COD/L), and hydrogen yield (mol $H_2$/mol $hexose_{added}$), respectively. The 2-D response surface clearly showed a high inter-dependency between initial pH and substrate concentration, and the role of these two factors was to control the pH during fermentation. According to the statistical optimization, the optimum condition of initial pH and substrate concentration were 7.0 and 13.4 g Carbo. COD/L, respectively, under which predicted $H_2$ yield was 1.84 mol $H_2$/mol $hexose_{added}$. Microbial analysis using 16S rRNA PCR-DGGE showed that $Clostridium$ sp. such as $Clostridium$ $perfringens$, $Clostridium$ $sticklandii$, and $Clostridium$ $bifermentans$ were main $H_2$-producers.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.5452-5457
• /
• 2012

It is saving material cost and construction cost by replacing conventional building materials, and It has advantages for aesthetic value. In the Europe, the United States, Japan and other country research about BIPV is actively being carried out and marketability is also being infinity expanding. Arch type PV systems efficiency characteristics is different depending on PV array's directly connection, parallel connection and arches angle, but is a lack of analysis on this nowadays. When the arch type PV system design up, they consider about aesthetic value and they didn't consider about generation efficiency. In this paper, we try to improve the efficiency through optimization of arch type PV system and estimation of the efficiency parameters of the arch type PV system, such as latitude, longitude, temperature, insolation, arch angle and each kind loss from system organization. For improving Arched PV system efficiency, proposed multiple control inverter system, and using simulation tool of Arched PV system "Solar pro", flat-plate type and many arch type PV system configuration the driving characteristics were compared and analyzed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.42.2-42.2
• /
• 2010

Transparent conducting oxides (TCOs) are of significant importance for their applications in various devices, such as light-emitting diodes, thin-film solar cells, organic light-emitting diodes, liquid crystal displays, and so on. In order for TCOs to contribute to the performance improvement of these devices, TCOs should have high transmittance and good electrical properties simultaneously. Sn-doped $In_2O_3$ (ITO) is the most commonly used TCO. However, indium is toxic and scarce in nature. Thus, ZnO has attracted a lot of attention because of the possibility for replacing ITO. In particular, group III impurity-doped ZnO showed the optoelectronic properties comparable to those of ITO electrodes. Al-doped ZnO exhibited the best performance among various doped ZnO films because of the high substitutional doping efficiency. However, in order for the Al-doped ZnO to replace ITO in electronic devices, their electrical and optical properties should further significantly be improved. In this connection, different ways such as a variation of deposition conditions, different deposition techniques, and post-deposition annealing processes have been investigated so far. Among the deposition methods, RF magnetron sputtering has been extensively used because of the easiness in controlling deposition parameters and its fast deposition rate. In addition, when combined with post-deposition annealing in a reducing ambient, the optoelectronic properties of Al-doped ZnO films were found to be further improved. In this presentation, we deposited Al-doped ZnO (ZnO:$Al_2O_3$ = 98:2 wt%) thin films on the glass and sapphire substrates using RF magnetron sputtering as a function of substrate temperature. In addition, the ZnO samples were annealed in different conditions, e.g., rapid thermal annealing (RTA) at $900^{\circ}C$ in $N_2$ ambient for 1 min, tube-furnace annealing at $500^{\circ}C$ in $N_2:H_2$=9:1 gas flow for 1 hour, or RTA combined with tube-furnace annealing. It is found that the mobilities and carrier concentrations of the samples are dependent on growth temperature followed by one of three subsequent post-deposition annealing conditions.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.23-32
• /
• 2006

Fast and accurate power bus design (FAPUD) method for multi-layers high-speed digital boards is devised for the power supply network design tool for accurate and precise high speed board. FAPUD is constructed, based on two main algorithms of the PBEC (Path Based Equivalent Circuit) model and the network synthesis method. The PBEC model exploits simple arithmetic expressions of the lumped 1-D circuit model from the electrical parameters of a 2-D power distribution network. The circuit level design based on PBEC is carried with the proposed regional approach. The circuit level design directly calculates and determines the size of on-chip decoupling capacitors, the size and the location of off-chip decoupling capacitors, and the effective inductances of the package power bus. As a design output, a lumped circuit model and a pre-layout of the power bus including a whole decoupling capacitors are obtained after processing FAPUD. In the tuning procedure, the board re-optimization considering simultaneous switching noise (SSN) added by I/O switching can be carried out because the I/O switching effect on a power supply noise can be estimated over the operation frequency range with the lumped circuit model. Furthermore, if a design changes or needs to be tuned, FAPUD can modify design by replacing decoupling capacitors without consuming other design resources. Finally, FAPUD is accurate compared with conventional PEEC-based design tools, and its design time is 10 times faster than that of conventional PEEC-based design tools.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.1
• /
• pp.8-16
• /
• 2004

An inversion method is presented for the determination of the compressional wave speed, compressional wave attenuation, thickness of the sediment layer and density as a function of depth for a horizontally stratified ocean bottom. An experiment for estimating those properties was conducted in the shallow water of South Sea in Korea. In the experiment, a light bulb implosion and the propagating sound were measured using a VLA (vertical line array). As a method for estimating the geoacoustic properties, a coherent broadband matched field processing combined with Genetic Algorithm was employed. When a time-dependent signal is very short, the Fourier transform results are not accurate, since the frequency components are not locatable in time and the windowed Fourier transform is limited by the length of the window. However, it is possible to do this using the wavelet transform a transform that yields a time-frequency representation of a signal. In this study, this transform is used to identify and extract the acoustic components from multipath time series. The inversion is formulated as an optimization problem which maximizes the cost function defined as a normalized correlation between the measured and modeled signals in the wavelet transform coefficient vector. The experiments and procedures for deploying the light bulbs and the coherent broadband inversion method are described, and the estimated geoacoustic profile in the vicinity of the VLA site is presented.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.3
• /
• pp.31-38
• /
• 2015

In order to achieve a high speed and high quality silicon wafer bonding, the room-temperature direct bonding using atmospheric pressure plasma and sprayed water vapor was developed. Effects of different plasma fabrication parameters, such as flow rate of $N_2$ gas, flow rate of CDA (clear dry air), gap between the plasma head and wafer surface, and plasma applied voltage, on plasma activation were investigated using the measurements of the contact angle. Influences of the annealing temperature and the annealing time on bonding strength were also investigated. The bonding strength of the bonded wafers was measured using a crack opening method. The optimized condition for the highest bonding strength was an annealing temperature of $400^{\circ}C$ and an annealing time of 2 hours. For the plasma activation conditions, the highest bonding strength was achieved at the plasma scan speed of 30 mm/sec and the number of plasma treatment of 4 times. After optimization of the plasma activation conditions and annealing conditions, the direct bonding of the silicon wafers was performed. The infrared transmission image and the cross sectional image of bonded interface indicated that there is no void and defects on the bonded wafers. The bonded wafer exhibited a bonding strength of average $2.3J/m^2$.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.1
• /
• pp.173-182
• /
• 2017

This study was conducted to investigate the change of Aaster scaber antioxidative activity, total phenolic compounds and flavonoids during the blanching processes. With two parameters such as blanching time and temperature, response surface methodology and central composite design was used to study the combined effect of blanching time (90 to 162 sec) and blanching temperature (75 to $99^{\circ}C$). We found that antioxidative activity, total phenolic compounds and flavonoids during the blanching processes were influenced by blanching temperature and time. Within process condition, total phenolic compounds and flavonoids were extracted 3.00 - 35.48 mg/g and 2.35 - 8.38 mg/g, respectively. DPPH radical scavenging activity was 42.10 - 67.14%. The change of total phenolic compounds, flavonoids, and DPPH radical scavenging activity was dependent of blanching temperature more than time. The total phenolic compounds was increased as temperature rise, but flavonoids not. However, DPPH radical scavenging activity was increased during the blanching process.

• Investigative Magnetic Resonance Imaging
• /
• v.13 no.2
• /
• pp.117-126
• /
• 2009

Purpose : A numerical method of designing a multiple quantum filter (MQF) is presented for the optimum detection of myo-inositol (mI), an important brain metabolite, by using in vivo proton nuclear magnetic resonance spectroscopy ($^1$-HMRS). Materials and Methods : Starting from the characterization of the metabolite, the filter design includes the optimization of the sequence parameters such as the two echo times (TEs), the mixing time (TM), and the flip angle and offset frequency of the 3rd $90^{\circ}$ pulse which converts multiple quantum coherences (MQCs) back into single quantum coherences (SQCs). The optimized filter was then tested both in phantom and in human brains. Results : The results demonstrate that the proposed MQF can improve the signal-to-background ratio of the target metabolite by a factor of more than three by effectively suppressing the signal from the background metabolites. Conclusion : By incorporating a numerical method into the design of MQFs in $^1$-HMRS the spectral integrity of a target metabolite, in particular, with a complicated spin system can be substantially enhanced.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.3
• /
• pp.53-58
• /
• 2008

In this study, we fabricated embedded IC (Double Pole Double throw switch chip) polymer substrate and evaluate it for 2.4 GHz WiFi application. The switch chips were laminated using FR4 and ABF(Ajinomoto build up film) as dielectric layer. The embedded DPDT chip substrate were interconnected by laser via and Cu pattern plating process. DSC(Differenntial Scanning Calorimetry) analysis and SEM image was employed to calculate the amount of curing and examine surface roughness for optimization of chip embedding process. ABF showed maximum peel strength with Cu layer when the procuring was $80\sim90%$ completed and DPDT chip was laminated in a polymer substrate without void. An embedded chip substrate and wire-bonded chip on substrate were designed and fabricated. The characteristics of two modules were measured by s-parameters (S11; return loss and S21; insertion loss). Insertion loss is less than 0.55 dB in two presented embedded chip board and wire-bonded chip board. Return loss of an embedded chip board is better than 25 dB up to 6 GHz frequency range, whereas return loss of wire-bonding chip board is worse than 20 dB above 2.4 GHz frequency.