• ETRI Journal
• /
• v.44 no.2
• /
• pp.260-273
• /
• 2022

This study presents a novel multilayer structure of parallel coupled-line bandpass filtercentered at 2.42 GHz with a fractional bandwidth value of approximately 19.4%. The designed filter can suppress harmonics with an appropriate frequency response by incorporating different techniques based on the multilayer technique. A combination of different techniques such as radial microstrip stubs and defected ground structure (DGS) and defected microstrip structure techniques are employed to suppress harmonics up to 5f₀. These techniques are used in two layers to suppress up to 5f₀. In addition, in this study, the effects of different parameters, such as the width of slot-line DGS, the angle of diagonal line slots in the upper layer, and the air gap between the two layers on the filter performance, are investigated. To verify the correct circuit operation, the designed filter is implemented and tested. The measurement results of the proposed filter are compared with the simulation results.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.2 s.35
• /
• pp.175-179
• /
• 2005

A novel, simple and broadband $180^{\circ}$ bit X-band phase shifter was proposed and fabricated in a standard micromachining process. It is composed of two $90^{\circ}$ parallel-coupled lines; one of which is shorted and the other is grounded. Design equations for the proposed $180^{\circ}$ bit phase shifter are derived by the method of even and odd mode analysis. Based on design equations, $180^{\circ}$ bit phase shifter was designed and fabricated to operate from 7 to 13 GHz with ${\pm}5^{\circ}$ of phase deviation.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.12
• /
• pp.1-11
• /
• 1998

A line profile synthesis method is presented that minimizes the nearest-neighbor crosstalk peak level for high-speed pulse transmission in multi-coupled microstrip signal buses. We adopted the optimization technique for the reflected wave control on bus lines resulting in increasing the average spacing between strip conductors, since in a parallel-conductor bus the crosstalk energy is concentrated at the nearest neighbors of the driven line. The generalized S-matrix technique is applied for the input and output waveform prediction, and crosstalk characteristics of various nonuniform lines synthesized for increasing the average spacing are analyzed by comparing each other. Simulation results demonstrate that the Chebyshev taper with dips is adequate to significantly minimize the crosstalk peak level under the satisfactory waveform integrity since the profile is oriented to evenly reflect significant pulse spectra within the frequency range of pulse.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.7
• /
• pp.752-759
• /
• 2013

This paper presents a method for analyzing and designing an extremely miniaturized planar ring hybrid, using the combination of parallel and diagonally shorted coupled lines. In contrast to conventional miniaturized coupled line filters, it is proven that the required electrical length of transmission line can be largely reduced to even a few degrees, not only effectively suppressing the spurious passband but also approximately maintaining the same characteristic around the stable center frequency. A ring hybrid filter at center frequency of 1 GHz was fabricated on the FR4 epoxy glass cloth copper-clad plat (CCL) PCB substrate. The insertion loss of a ring hybrid filter with the die area of $30mm{\times}30mm$ is -4.68 dB. Simulated results are well agreed with the measurements.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.1054-1060
• /
• 2002

In this paper, a new parallel-coupled-line microstrip BPF(BandPass Filter) improving the suppression performance of 2nd harmonic signals is studied. Using the consecutive pattern in coupled-line, the desired passband performance is improved and harmonic passband signal is rejected. Recalculation of classical filter design parameters(space-gap between lines, line widths and lengths) is not required. That is, after using the classical design methodology for parellel-coupled-line BPF, new filters can be easily realized by inserting periodic patterns in coupled-line. To investigate the validity of this novel technique, order-3 Butterworth BPF centered at 2.5 GHz with a 10 % FBW(Fractional Bandwidth) and order-5 Chebyshev BPF centered at 10 GHz with a 15 % FBW were used. When five and three square grooves are used, over 30 dB harmonic suppression at 2nd harmonic is achieved in simulation and experiment.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.7 s.337
• /
• pp.41-48
• /
• 2005

We design and fabricate 3-dB tandem directional coupler using the coplanar waveguide structure which is applicable to balanced amplifiers and mixers for 60 GHz wireless local area network system. The coupler comprises the multiple-sectional parallel-coupled lines to facilitate the fabrication process, and enable smaller device size and higher directivity than those of the conventional 3-dB coupler employing the edge-coupled line. In this study, we adopt the structure of two-sectional parallel-coupled lines of which each single-coupled line has a coupling coefficient of -8.34 dB and airbridge structure to monolithically materialize the uniplanar coupler structure instead of using the conventional multilayer or bonded structure. The airbridge structure also supports to minimize the parasitic components and maintain desirable device performance in V-band (50$\~$75 GHz). The measured results from the fabricated couplers show couplings of 3.S$\~$4 dB and phase differences of 87.5$^{\circ}{\pm}1^{\circ}$ in V-band range and show directivities higher than 30 dB at a frequency of 60 GHz.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.3
• /
• pp.232-239
• /
• 2010

By using the clock timing control at transmitter (TX), the crosstalk-induced jitter (CIJ) is compensated for in the 2-bit parallel data transmission through the coupled microstrip lines on printed circuit board (PCB). Compared to the authors' prior work, the delay block circuit is simplified by combining a delay block with a minimal number of stages and a 3-to-1 multiplexer. The delay block generates three clock signals with different delays corresponding to the channel delay of three different signal modes. The 3-to-1 multiplexer selects one of the three clock signals for TX timing depending on the signal mode. The TX is implemented by using a $0.18\;{\mu}m$ CMOS process. The measurement shows that the TX reduces the RX jitters by about 38 ps at the data rates from 2.6 Gbps to 3.8 Gbps. Compared to the authors' prior work, the amount of RX Jitter reduction increases from 28 ps to 38 ps by using the improved implementation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.7
• /
• pp.1193-1203
• /
• 2016

This paper proposes a droop control scheme to compensate the unbalanced line-to-line voltage of unbalanced 3-phase load which is coupled with two inverter-based distributed generations through unequal impedance lines. Unbalanced line-to-line load voltages occur due to using single-phase loads, which brings about bad effects on the coupled inverters and the distributed generations. In order to compensate the unbalanced line-to-line voltages, a positive sequence voltage control was used for sharing the active and reactive power and a negative sequence control was used for reducing the negative sequence voltage. The feasibility of the proposed scheme was first verified by computer simulations, and then experiments with a hardware set-up built in the lab. The experimental results were compared with the simulation results to confirm the feasibility of the proposed scheme.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.10
• /
• pp.1004-1010
• /
• 2003

In this paper, the 1/4 wavelength backward-wave directional coupler using coupled lines with finite metallization thickness is described. A mode-matching method, simple and fast approach to the quasi-static analysis, has been used to analyse this structure. The numerical results show that it is possible to overcome the disadvantages of weakly coupling, low directivity, and narrow strip distance non-realizable in the case of 1/4 wavelength backward-wave directional coupler with zero thickness conductor. It is also revealed that thicker metallization causes longer coupler length in the case of backward-wave symmetrical parallel coupled line directional coupler. The finite metallization thickness can be a new parameter for tight coupling in the design of backward-wave directional couplers, which enables us to design more accurate properties of monolithic microwave integrated circuits.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.8
• /
• pp.995-999
• /
• 2014

In this paper, a new size-reduction approach for branch-line coupler is introduced which uses parallel end-shorted coupled lines with lumped capacitors. The characteristic of the new design was analyzed using even-odd mode method, and simulated on HFSS before fabricated on the FR4 epoxy glass cloth copper-clad plat (CCL) PCB substrate at center frequency of 1 GHz. The electrical length of transmission line was reduced to 15 degrees, therefore the size of branch-line coupler was largely reduced approximately maintaining the same characteristic around the stable center frequency. The insertion loss of the branch-line coupler filter was -4.39 dB. The size of the overall hybrid is $20mm{\times}20mm$. Measurements results were well agreed with the simulated ones.