• 대한전자공학회논문지TC
• /
• 제43권10호
• /
• pp.90-97
• /
• 2006

본 논문에서는 cascode 구조에 shunt peaking 기술을 접목시킨 밀리미터파 광대역 amplifier를 설계 및 제작하였다. 밀리미터파 광대역 cascode amplifier의 설계 및 제작을 위해서 $0.1{\mu}m\;{\Gamma}-gate$ GaAs PHEMT와 CPW 및 passive library를 개발하였다. 제작된 PHEMT는 최대 전달 컨덕턴스는 346.3 mS/mm, 전류이득 차단 주파수 ($f_T$)는 113 GHz, 그리고 최대공진 주파수($f_{max}$)는 180 GHz의 특성을 갖고 있다. 설계된 cascode amplifier는 회로의 발진을 막기 위해서 저항과 캐패시터를 common-rate 소자의 드레인에 병렬로 연결하였다. 대역폭의 확장 및 gain의 평탄화를 위해 바이어스 단들에 short stub 및 common-source 소자와 common-gate 소자 사이에 보상 전송선로를 삽입하고 최적화하였으며, 입출력 단은 광대역 특성을 갖는 정합회로로 설계하였다. 제작된 cascode amplifier의 측정결과, cascode 구조에 shunt peaking 기술을 접목시킴으로써 대역폭을 확장 및 gain을 평탄화 시킬 수 있다는 것을 확인하였다. 3 dB 대역폭은 34.5 GHz ($19{\sim}53.5GHz$)로 광대역 특성을 얻었으며, 3 dB대역 내에서 평균 6.5 dB의 $S_{21}$ 이득 특성을 나타내었다.

• Transactions on Electrical and Electronic Materials
• /
• 제15권2호
• /
• pp.103-111
• /
• 2014

This paper investigates the output powers of PV modules by predicting three unknown parameters: reverse saturation current, and series and shunt resistances. A theoretical model using the non-uniform physical parameters of solar cells, including the temperature coefficients, voltage, current, series and shunt resistances, is proposed to obtain the I-V characteristics of PV modules. The solar irradiation effect is included in the model to improve the accuracy of the output power. Analytical and Newton methods are implemented in MATLAB to calculate a module output. Experimental data of the non-uniform solar cells for both serial and parallel connections are used to extend the implementation of the model based on the I-V equation of the equivalent circuit of the cells and to extend the application of the model to m by n modules configuration. Moreover, the theoretical model incorporates, for the first time, the variations of series and shunt resistances, reverse saturation current and irradiation for easy implementation in real power generation. Finally, this model can be useful in predicting the degradation of a PV system because of evaluating the variations of series and shunt resistances, which are critical in the reliability analysis of PV power generation.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.802-807
• /
• 1998

The main drawback of parallel type active power filters (APF) is the large capacity required for harmonic compensation. This paper evaluates the APF capacity requirement of harmonic/reactive power compensation for thyristor converter load. Theoretically achievable maximum power factor under partial load is evaluated. And it is shown that the APF capacity can be considerably reduced while slightly sacrificing the filtering performance by deliberately limiting the peak current of the APF.

• 제어로봇시스템학회논문지
• /
• 제7권6호
• /
• pp.494-501
• /
• 2001

In this paper an ANFIS(Adativo Neuro-Fuzzy Inference System)- based fault detection and diagnosis for a closed loop control system is proposed. The proposed diagnostic system contains two ANFIS. One is run as a parallel model within the model in closed loop control(MCL) and the other is run as a series-parallel model within the process in closed loop(PCL) for the generation of relevant symptoms for fault diagnosis. These symptoms are further processed by another classification logic with simple rules and neural network for process and controller fault diagnosis. Experimental results for a DC shunt motor control system illustrate the effectiveness of the proposed diagnostic scheme.

• Journal of Electrical Engineering and Technology
• /
• 제4권4호
• /
• pp.457-466
• /
• 2009

This paper presents efficient parallel genetic algorithm (EPGA) based decomposed network for optimal power flow with various kinds of objective functions such as those including prohibited zones, multiple fuels, and multiple areas. Two coordinated sub problems are proposed: the first sub problem is an active power dispatch (APD) based parallel GA; a global database generated containing the best partitioned network: the second subproblem is an optimal setting of control variables such as generators voltages, tap position of tap changing transformers, and the dynamic reactive power of SVC Controllers installed at a critical buses. The proposed approach tested on IEEE 6-bus, IEEE 30-bus and to 15 generating units and compared with global optimization methods (GA, DE, FGA, PSO, MDE, ICA-PSO). The results show that the proposed approach can converge to the near solution and obtain a competitive solution with a reasonable time.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.272-275
• /
• 2000

We investigated a resistive superconducting fault current limiter (SFCL) fabricated using YBCO thin films on 2-inch diameter sapphire substrates. Nearly identical SFCL units were prepared and tested. The units were connected in series and parallel to increase the current and voltage ratings. A serial connection of the units showed significantly unbalanced power dissipation between the units. This imbalance was removed by introducing a shunt resistor to the firstly quenched unit. Parallel connection of the units increased the current rating. An SFCL module of 4 units in parallel, each of which has minimum quench current 25 Ap, was produced and successfully tested at a 220 V circuit. From the resistance increase, we estimated that the film temperature increases to 200 K in 5 msec, and 300 K in 120 msec. Successive quenches revealed that this system is stable without degradation in the current limiting capability under such thermal shocks as quenches at 220 V.

• 한국전자통신학회논문지
• /
• 제14권1호
• /
• pp.81-86
• /
• 2019

본 논문은 복수개의 스위칭모드 전원장치를 병렬 결선을 통하여 부하에 보다 큰 전력을 공급가능하게 하는 시스템 설계에 관한 것이다. 이를 위해 정전압조정기의 출력단에 션트저항을 직렬로 배치하고 아두이노를 이용하여 출력단 전압을 감지하고 제어하도록 하였다. 본 논문에서는 실험을 위해 두 개의 정전압조정기를 이용하였으나 그 이상의 보드에 대해서도 일반화가 가능할 것이다. 이와 같은 방식으로 제어되는 시스템을 통해 두 개의 시스템이 부하에 전달되는 전류의 합이 각각의 보드에서 나온 전류의 96%가 부하에 전달되는 것을 확인하였다. 효율의 경우 단위 보드에서의 효율은 92.4% 정도가 나왔으며 병렬결선 시에는 90% 정도가 나왔다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.663-665
• /
• 2000

We fabricated resistive superconducting fault current limiters (SFCL) based on YBCO thin films grown on 2-inch diameter saphire substrates Two SFCLs with nearly identical properties were connected in series to investigate the simultaneous quench. There was a slight difference in the rate of voltage increase between two SFCL units when they were operated independently. This difference. however, resulted in significantly unbalanced power dissipation between the units. This imbalance was removed by connecting a shunt resistor to an SFCL in parallel. The appropriate values of the shunt resistances were $80{\Omega}$ at $75 V_{rms}$. $100{\Omega}$ at $100 V_{rms}$ and $110{\Omega}$ at $120 V_{rms}$, respectively. Increased power input at high voltages also reduced the initial imbalance in power dissipation. but with increase in film temperature to higher than 200 K.

• 전기학회논문지
• /
• 제56권2호
• /
• pp.277-281
• /
• 2007

We investigated fault current limitation characteristics of the resistive superconducting fault current limiter (SFCL) which consisted of a Bi-2212 bulk coil and a shunt coil. The Bi-2212 bulk coil and the shunt coil were connected in parallel. The Bi-2212 bulk coil was placed inside the shunt coil to induce field-assisted quench. The fault test was conducted at an input voltage of $200V_{rms}$ and fault current of $12kA_{rms}\;and\;25kA_{rms}$. The fault conditions were asymmetric and symmetric, and the fault period was 5 cycles. The test results show that the SFCL successfully limited the fault current of $12kA_{rms}\;and\;25kA_{rms}$ to below $5.5{\sim}6.9kA_{peak}\;within\;0.64{\sim}2.17$ msec after the fault occurred. Limitation was faster under symmetric fault test condition due to the larger change rate of current. We concluded that the speed of fault current limitation was determined by the speed of current rise rather than the amplitude of a short circuit current. These results show that the Bi-2212 bulk coil is suitable for distribution-class SFCLS.

• Progress in Superconductivity
• /
• 제7권2호
• /
• pp.114-119
• /
• 2006

High critical current density, high n value, multiple faults endurances, and fast recovery characteristics of YBCO thin films are very attractive characteristics for developing resistive type superconducting fault current limiters. But due to the limited current and voltage ratings of one YBCO module, it is needed to construct series and parallel module connections for high capacity electric networks. Especially for distribution network, more than 30 units should be connected in series to meet voltage level. So in order to construct distribution-level superconducting fault current limiter, simultaneous quench in one YBCO thin films should be realized, and furthermore, quench should be occurred in all fault current limiting units equally to avoid local heating and failures. In this paper, we proposed optimum design of YBCO thin films for fault current limiting module and technical method using shunt resistor to achieve simultaneous quench between multi current limiting units. From the analytical and the experimental results, optimal current path and thickness of shunt material was determined for YBCO thin films and shunt resistor between modules was developed. Finally, 14 kV one phase resistive fault current limiter using multi YBCO thin films was constructed and it was possible to get satisfactory test results.