• 전력전자학회논문지
• /
• 제9권5호
• /
• pp.457-466
• /
• 2004

본 논문에서는 태양광 컨버터로서 변형된 벅-부스트 컨버터를 제안하고 분석하며, 출력을 증가시키고 출력전압의 리플을 저감하기 위한 새로운 병렬 구동 기법을 제안한다. 변형된 컨버터의 입ㆍ출력 관계는 기존의 승압형 컨버터인 부스트 컨버터와 동일하지만, 출력단자의 구성을 변형시켜 출력 콘덴서의 동작전압과 커패시턴스 용량을 저감시킬 수 있는 장점을 가진다. 또한 변형된 컨버터와 전류 제어 기법을 이용하는 제안된 병렬구동 기법은 기존병렬 구동 방식의 전류 분배에 대한 불평등 문제를 해결할 수 있으며, 부가적인 스위칭 손실의 증가 없이 등가 스위칭 주파수를 증가 시킬 수 있어 출력전압 리플 저감에 효과적이다. 제안된 병렬 구동 기법의 타당성을 컴퓨터 시뮬레이션과 실험을 통하여 입증한다.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권2호
• /
• pp.98-104
• /
• 2012

This paper presents a novel transformer isolated parallel connected full-bridge dc-dc converter using recently developed trans-Z-source network. Unlike the traditional voltage -fed or current-fed converters, the proposed converter can be open- and short-circuited without damaging switching devices. Therefore, the desired buck and boost function can be achieved and the converter reliability can be greatly improved. A 6 kW prototype dc-dc converter is built and tested to verify performances of the proposed converter.

• 전력전자학회논문지
• /
• 제23권1호
• /
• pp.40-46
• /
• 2018

In this study, the output voltage balancing characteristics of parallel-input series-output (PISO) boost converter is analyzed. The PISO boost converter is derived by combining two basic boost converters. In comparison with the conventional three-level boost converter, the PISO boost converter can balance the output voltages under an unbalanced load condition without requiring additional circuit components and control strategy. A 2 kW prototype converter is built and tested to verify the output voltage balancing characteristics of the PISO boost converter.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.472-475
• /
• 1999

An improved series-parallel resonant converter using auxiliary winding of resonant is presented. The conventional series-parallel resonan converter and newly developed converter are compared for high voltage application. This proposed converter gives several merits such a wide load ranges, small circulating current, low peak voltage at no load. Two experimental results for the proposed converter and conventional one are presented for conventional LCC type converter and the proposed one.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 전기.전자공학 학술대회 논문집(II)
• /
• pp.1166-1169
• /
• 1987

A new analog-la-digital structure. called cyclic-parallel analog-to-digital(A/D) converter, has been developed for video applications. It consists of a M-bit parallel A/D converter, a digital-to-analog(D/A) converter, a differencing amplifier with gain of $2^M$ and two sample-and-hold circuits. In this structure, the input signal is circulated around the circuits K times, thereby converted into a MK-bit digital word. The proposed converter retains speed advantages of conventional series-parallel converters, with half reduced circuit components.

• 전력전자학회논문지
• /
• 제22권1호
• /
• pp.9-17
• /
• 2017

A parallel control algorithm of thyristor dual-converter power system for the DC power supply of railway is proposed. The circulating current and current imbalance generated during parallel operation can be limited to control the output voltage of each power system by using the proposed parallel control algorithm. The proposed control algorithm can also eliminate output current sensor to achieve the same output response without additional costs. The validity of the proposed algorithm is verified through simulation and experiment.

• 전기학회논문지
• /
• 제66권2호
• /
• pp.459-467
• /
• 2017

An urban railway power substation consists of three thyristor dual converters. Two converters are connected to up and down trolley line to supply the electric energy or feed the regenerative energy back to the distribution. When the two converters break down, the remaining converter is used in an emergency. One thyristor dual converter system (TDCS) manages the energy of two or three railway stations. If the TDCS fails, the trains stop operating. To solve the problem, this paper proposes the three parallel operation control algorithm of thyristor dual converter system using the emergency converter. The broken TDCS can be replaced by the emergency converter in other TDCS. The effectiveness of this proposed control is verified by simulation.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.533-541
• /
• 2011

The redundant operation of a parallel AC to DC converter via a serial communication bus is presented. The proposed system consists of three isolated CUK power factor correction modules. The controller for each converter is a dsPIC30F6010 microcontroller while a RS485 communication bus and the clock signal are used for synchronizing the data communication. The control strategy of the redundant operation relies on the communication of information among each of the modules, which communicate via a RS485 serial bus. This information is received from the communication checks of the converter module connected to the system to share the load current. Performance evaluations were conducted through experimentation on a three-module parallel-connected prototype, with a 578W load and a -48V dc output voltage. The proposed system has achieved the following: the current sharing is quite good, both the transient response and the steady state. The converter modules can perform the current sharing immediately, when a fault is found in another converter module. In addition, the transient response occurs in the system, and the output voltages are at their minimum overshoot and undershoot. Finally, the proposed system has a relatively simple implementation for the redundant operation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.942-945
• /
• 2001

This paper presents parallel operation of ZVT(Zero Voltage Transition) Full Bridge Converter with Dynamic Current Shared Inductor. In the conventional method, CT(Current Transformer) have been used to share the load current equally with converters. In this system, at parallel operation of ZVT Full Bridge Converter, dynamic current shared inductor divides the same current of unit converter and ZVT circuit aids to high efficiency. This method which is proposed to compare in the conventional method will do simple control circuit. To show the superiority of this converter is verified through the experiment with a 2kW, 50kHz prototype converter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.324-328
• /
• 2001

This paper presents parallel operation and control loop design of ZVT(Zero Voltage Transition) Full Bridge DC/DC Converter. At parallel operation of ZVT Full Bridge Converter, dynamic current shared inductor devides the same current of unit converter and ZVT circuit and aids to high efficiency in the system. Base on the modeling of ZVT. Full Bridge Converter, the control loop is designed using a simple two-pole, one-zero compensation circuit. To show the validity of the design procedures, the small signal analysis of the closed loop system and open loop system is carried out and the superiority of the dynamic characteristics is verified through the experiment with a 2kW, 50kHz prototype converter.