• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.5
• /
• pp.289-293
• /
• 2016

The flux-lock type superconducting fault current limiter (SFCL) connects the two parallel windings in parallel with a ferromagnetic core. We suggest that the double quench flux-lock type SFCL should add a third winding. We analyzed characteristics of the fault current and the peak current using the quench of the high-Tc superconducting element. The proposed SFCL's inductances of a primary winding and the third winding were fixed and the amplitude of inductance of the secondary winding was changed. We found that the fault current can be more effectively controlled through the analysis of the equivalent circuit and the short-circuit tests.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.15 no.6
• /
• pp.467-474
• /
• 1990

In this paper, the circuit that has characteristics of high speed and low dissipation is described. A 4:1 parallel ADC is constructed by using the designed SCFL(Source Coupled FET Logic). The results of simulation shows that comparators is obtained integrated nonlinearity, $\pm$28mV, compared with limiting value, $\pm$68mV, at 66NHz input signal and 2Gs/s Niquist rates and this paper describes low power dissipation about 0.43W by reducing the elements in a ADC design.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.180-180
• /
• 2012

A microplasma system source based on microwave parallel stripline resonator (MPSR) was developed for the generation of microplasmas in a wide range of pressure from some torr to 760 torr. This source was operated at its resonance frequency that much depends upon not only its discharge gap size but also operated pressure. This paper applied a simple circuit model to analyze the effects of discharge gap size and pressure to resonance frequency and impedance of MPSR in the cases with and without plasma exist inside the discharge gap. In the process of calculating, the conformal mapping method was used to estimate the capacitance of the MPSR. The calculating results by using circuit model agree well with the simulation results that using commercial CST microwave studio software.

• ETRI Journal
• /
• v.34 no.2
• /
• pp.210-215
• /
• 2012

In this paper, a group delay time controller (GDTC) is proposed based on a reflection topology employing a parallel resonator as the reflection termination. The design equations of the proposed GDTC have been derived and validated by simulation and experimental results. The group delay time can be varied by varying the capacitance and inductance at an operating frequency. To show the validity of the proposed circuit, an experiment was performed for a wideband code division multiple access downlink band operating at 2.11 GHz to 2.17 GHz. According to the experiment, a group delay time variation of $3{\pm}0.17$ ns over bandwidth of 60 MHz with excellent flatness is obtained.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.4
• /
• pp.7-13
• /
• 2001

In this paper, the external-exciting electronic ballast for an 100[W] high pressure sodium lamp using full-bridge inviter is designed. The L-C parallel full-bridge invert circuit for P-SPICE simulation is designed. The values of inductor and capacitor in the proposed equivalent L-C parallel resonant tank circuit are calculated theoretically. Then the ballast for high pressure sodium lamp is implemented using the simulated results. In the experimental results, that is confirmed which the results of implemented ballast are really same with the of simulated one.

• Journal of Navigation and Port Research
• /
• v.30 no.7
• /
• pp.607-610
• /
• 2006

A new compact microstrip low-pass filter and its equivalent-circuit model are developed. The philosophy of the structure behind this novel microstrip low-pass filter is simple as it is composed of a pair of symmetrical parallel coupled-line and an open-stub. With this configuration, a finite attenuation pole near the stopband cutoff frequency is available and adjustable by simply tuning the circuit parameters. Furthermore, the rejection bandwidth of this type of low-pass filter can be extended. In order to validate the feasibility of the proposed design method, a low-pass filter based on a microstrip structure is designed, fabricated, and measured. Experimental results agree very well with the simulation and analytical results.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.9
• /
• pp.408-413
• /
• 2005

This paper presents the basic design technology on the hybrid type GCB(gas circuit breakers) through the test results. The three type hybrid interrupters according to the arrangement of the thermal expansion chamber and the puffer cylinder(they are called 'serial type', ' parallel/exchanged type ,' and ' parallel/separated type ' respectively in this work) were designed and manufactured and then the tests of operating characteristics and interrupting were performed using a simplified synthetic test facility. The interruption capability with the type and the opening speed and the pressure rise which is required to interrupt were examined. The change of pressure rise with the number of interruption was given quantitatively and therefore the pressure rise can be predicted. Finally, it was shown that the interruption capability tends to increase with the increasing of opening speed in the puffer type; however, the hybrid type interrupter has a different interruption characteristic.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.3
• /
• pp.544-551
• /
• 2011

This paper presents the circuit arrangement and effective control method of regenerative energy storage system for an electric vehicle using super-capacitors as the braking energy storage element. A bi-directional controlled current flow of the DC-DC converters with the capacitor bank is connected in parallel with battery, and is controlled so that the whole of the braking energy is effectively absorbed into the capacitors and released back to the electric motor upon acceleration. The converter needs the series-parallel switching circuit for making the best use of the series capacitors and for limiting the step-up ratio of the boost converter. The proposed methods are verified by computer simulation and experimental set-up. They are usefully applied to the electric vehicles such as green cars, electric motorcycles, bike, etc which are power- supplied by the electric batteries.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.3
• /
• pp.309-316
• /
• 1986

A concatenated coding system using a binary code as the inner code and a nonbinary code as the outer code has been constructed for the purpose of error correction. The complexity of a conventional coding system grows exponentially as the code length of a block code becomes longer. To reduce the complexity for ling code, an effective communication system has been proposed by cascading two codes-binary and norbinary codes. Using a parallel-to-serial circuit and a serial-to-parallel circuit, the concatenated coding system has been designed and constructed by empolying a (7,3) burst error correcting code as the inner code and a (7,3) Reed-Solomon code as the outer code. This system has been simulated and tested using a micro-computer. For the (49,9) concatenated coding system, the error probability of the channel has been evaluated and compared to different coding systems.

• Journal of Power Electronics
• /
• v.6 no.4
• /
• pp.330-339
• /
• 2006

This paper deals with novel electronic ballast based on single-stage power processing topology using a symmetrical half-bridge inverter and current injection circuit. The half-bridge inverter drives the output parallel resonant circuit and injects current through the power factor correction (PFC) circuit. Because of high frequency current injection and high frequency modulated voltage, the proposed circuit maintains the unity power factor (UPF) with low THD even under wide variation in ac input voltage. This circuit needs minimum and lower sized components to achieve the UPF and high efficiency. This leads to an increase in reliability of ballast at low cost. Furthermore, to reduce cost, the electronic ballast is designed for two series-connected fluorescent lamps (FL). The analysis and experimental results are presented for ($2{\times}36$ Watt) fluorescent lamps operating at 50 kHz switching frequency and input line voltage (230 V, 50 Hz).