• Polymer(Korea)
• /
• v.25 no.6
• /
• pp.855-865
• /
• 2001

The optimization condition of injection molding for a commercial product of TV speaker grille of A Company was induced using a CAE software of Moldflow. The flow and packing phase analysis was performed by using flow balance, runner balance, and the intermediate one by using the above two balances, which were used for controlling the amount of packing resins into the cavity, Later, the analysis performed by using the measured viscosity (local database) at various shear rates and the results were compared with the computer simulation using the standard database. Flow balance induced minimized weld line resulted in a better appearance and physical properties of the were line, but exhibited a disadvantage of large deformation and gas formation due to over-packing of the molten resin in the center of the speaker grille. Runner balance improved the disadvantage of the flow balance by controlling the amount of molten resin injected from the gate, however resulted reduced mechanical properties and poor appearance of the weld line. However, the modified method induced from the flow and runner balance improved the disadvantages by changing the runner size. In addition, the analyses based on the local database and the standard database were compared. Although the measured viscosity was slightly higher and the temperature distribution was broader than the standard database, no distinct difference was obtained from the analysis using the two different databases.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.51-51
• /
• 2012

Cellulose is extremely difficult to dissolve cellulose in water and most common organic solvents due to their stiff molecular structure, close chain packing and intermolecular hydrogen bonds. Recently, cellulose solutions using ionic liquids (ILs) as a green solvent have been known to form cholesteric liquid crystalline phase at high cellulose concentration. In this study, the phase transition and rheological behaviors of concentrated cellulose/[AMIM]Cl solution were investigated using polarized optical microscopy and rheometry. Studies were conducted to characterize the influence of cellulose concentration on the phase transition of the cellulose solution and the mechanical properties of the regenerated fibers spun from the anisotropic cellulose/[AMIM]Cl solutions.

• KSBB Journal
• /
• v.32 no.2
• /
• pp.103-107
• /
• 2017

The effect of the trehalose incorporation on the biological membranes was investigated with respect to the phase of the membranes using the fluorescence intensity change. Spherical phospholipid bilayers, vesicles, were prepared only with the variation in the phase of each layer via a double emulsion technique. In the aqueous inside of the vesicles, 8-Aminonaphthalene-1,3,6-trisulfonic acid disodium salt(ANTS) was encapsulated. As a quencher, p-Xylene-bis(N-pyridinium bromide)(DPX) was included in the buffer where the vesicles were dispersed. The fluorescence scale was calibrated with the fluorescence of ANTS vesicles in p-Xylene-bis(N-pyridinium bromide)(DPX)-included-buffer taken as 100% fluorescence and the mixture of ANTS and DPX in the buffer as 0% fluorescence. Trehalose injection into the vesicle solution led the distortion of the membrane. It was found that the distortion was related to the phase of each layer the vesicle up on the ratio of trehalose to lipid. In the identical measurements at glucose, the behavior of the distortion was completely different from that of trehalose. These results seem to depend on the stability of the vesicles, due to the osmotic and volumetric effects on the headgroup packing disruption.

• Applied Microscopy
• /
• v.50
• /
• pp.7.1-7.10
• /
• 2020

Tantalum nitride (TaN_x) thin films were grown utilizing an inductively coupled plasma (ICP) assisted direct current (DC) sputtering, and 20-100% improved microhardness values were obtained. The detailed microstructural changes of the TaN_x films were characterized utilizing transmission electron microscopy (TEM), as a function of nitrogen gas fraction and ICP power. As nitrogen gas fraction increases from 0.05 to 0.15, the TaN_x phase evolves from body-centered-cubic (b.c.c.) TaN_0.1, to face-centered-cubic (f.c.c.) δ-TaN, to hexagonal-close-packing (h.c.p.) ε-TaN phase. By increasing ICP power from 100 W to 400 W, the f.c.c. δ- TaN phase becomes the main phase in all nitrogen fractions investigated. The higher ICP power enhances the mobility of Ta and N ions, which stabilizes the δ-TaN phase like a high-temperature regime and removes the micro-voids between the columnar grains in the TaN_x film. The dense δ-TaN structure with reduced columnar grains and micro-voids increases the strength of the TaN_x film.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.7
• /
• pp.625-631
• /
• 2015

In this study, a numerical analysis on the discharging performance of a thermal storage tank completely filled with packing modules is investigated. The enthalpy-porosity method is adopted to analyze phase change phenomenon. Using this method, the melting process of a packing module in the thermal storage tank was studied as the HTF (heat transfer fluid) flows down from the top of the tank at the discharging mode. There are some design factors such as the module arrangement and the number of modules, but this study focuses on the effects of varying the flow rate of the HTF on the outlet temperature of the HTF, molten fraction, and thermal storage density. As the flow rate increases, the outlet temperature of the HTF gets higher and the total melting time of the PCM decreases. Additionally, the thermal storage density is increased so that it reaches about 93% for the desired value.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.10a
• /
• pp.94-95
• /
• 2016

Calcium Silicate Hydrate (C-S-H), which takes up most of the hydration products of Portland Cement (PC), has the greatest impact on the mechanical behavior and strength development of concrete. The exact mechanism of its deformation, however, has not yet been elucidated. The present study aims to demonstrate the mechanism of nano-deformation behavior of C-S-H in tricalcium silicate paste under compressive loading, unloading and reloading by interpreting atomic pair distribution function (PDF) based on synchrotron X-ray scattering. The strain of the tricalcium silicate paste for a short-range of 0 ~ 20 Å under compressive load exhibited two stages, I) nano-packing of interlayer of C-S-H and II) micro-packing of C-S-H globules, whereas the deformation for a long-range order of 20 ~ 40 Å was similar to that of a calcium hydroxide phase measured by Bragg peak shift. Moreover, the residual strains due to the plastic deformation of C-S-H was clearly observed.

• Journal of the Korean Vacuum Society
• /
• v.6 no.S1
• /
• pp.75-79
• /
• 1997

Optical and mechanical characteristics of $TiO-2, ZrO_2 \;and\; SiO_xN_y$ thin films prepared by ion assisted deposition (IAD) were investigated. IAD films were bombarded by Ar or nitrogen ion beam from a Kaufman ion source while they were grown in as e-beam evaporator. The result shows that the Ae IAD increases the refractive index and packing density of $TiO_2 films close to those of the bulk. For $ZrO_2$ films the Ar IAD increases the average refractive index decreases the negative inhomogeneity of refractive index and reverses to the positive inhomogeneity. The optical properties result from improved packing density and denser outer layer next to air The Ar-ion bombardment also induces the changes in microstructure of $ZrO_2$ films such as the preferred (111) orientation of cubic phase increase in compressive stress and reduction of surface roughness. Inhomogeneous refractive index SiOxNy films were also prepared by nitrogen IAD and variable refractive index of $SiO_xN_y$ film was applied to fabricate a rugate filter.

• Journal of the Korean Ceramic Society
• /
• v.33 no.8
• /
• pp.921-927
• /
• 1996

The liquid-phase concentration from the interior to the surface region and its influence on the microstructural changes were investigated in pressureless sintered $\beta$-SiC Surface reaction-layer was formed by reaction of packing powder and volatile components on the surface during sintering which was induced the concentration of liquid-phase in the surface regions. The microstructural changes between the surface region and the interior were appeared in sintered specimen which was resulted from the difference of liquid-phase content during sintering. Microstructural changes were observd with the depth of about 250${\mu}{\textrm}{m}$ from he surface. The grain size and aspect ratio of SiC in the interior are larger than those in the surface region and the rate of transforma-tion of $\beta$-to $\alpha$-SiC during sintering is higher in the interior than that in the surface region.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.186-192
• /
• 1999

Dang-Chin feldspar powder with the mean particle size of 9.1 $\mu\textrm{m}$ was added to the synthesized mullite powder with the particle size of +325∼-200 mesh and the powder compact was prepared by PLPP(pressureless powder packing method). Densification behaviors were observed in sintering temperature range of 1200∼1400$^{\circ}C$. The binder solution of 4% PVA was infilterated into packed powder to the suitable strength. The PLPP method makes it possible to form compacts without clay as plasticizer. Therfore there was no defect caused by phase transition after sintering. Additionally, we observed the dense microstructure by the melting of feldspar. When the mullite compacts with feldspar of 30% were sintered at 1300$^{\circ}C$-4 hrs, we obtained the dense microstructure with zero water absorption and porosity <1%. When these compacts were sintered longer than 4 hrs at 1300$^{\circ}C$ or higher than 1400$^{\circ}C$, the examggerated grain growth of mullite was observed.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1993.10a
• /
• pp.12-19
• /
• 1993

In general, the line balancing problem is defined as of finding an assignment of the given jobs to the workstations under the precedence constraints given to the set of jobs. Usually, the objective is either minimizing the cycle time under the given number of workstations or minimizing the number of workstations under the given cycle time. In this paper, we present a new type of an assembly line balancing problem which occurs in an electronics company manufacturing home appliances. The main difference of the problem compared to the general line balancing problem lies in the structure of the precedence given to the set of jobs. In the problem, the set of jobs is partitioned into two disjoint subjects. One is called the set of fixed jobs and the other, the set of floating jobs. The fixed jobs should be processed in the linear order and some pair of the jobs should not be assigned to the same workstations. Whereas, to each floating job, a set of ranges is given. The range is given in terms of two fixed jobs and it means that the floating job can be processed after the first job is processed and before the second job is processed. There can be more than one range associated to a floating job. We present a procedure to find an approximate solution to the problem. The procedure consists of two major parts. One is to find the assignment of the floating jobs under the given (feasible) assignment of the fixed jobs. The problem can be viewed as a constrained bin packing problem. The other is to find the assignment of the whole jobs under the given linear precedence on the set of the floating jobs. First problem is NP-hard and we devise a heuristic procedure to the problem based on the transportation problem and matching problem. The second problem can be solved in polynomial time by the shortest path method. The algorithm works in iterative manner. One step is composed of two phases. In the first phase, we solve the constrained bin packing problem. In the second phase, the shortest path problem is solved using the phase 1 result. The result of the phase 2 is used as an input to the phase 1 problem at the next step. We test the proposed algorithm on the set of real data found in the washing machine assembly line.