• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.124-131
• /
• 2019

A design study of gas turbine engine simulation duct was conducted to investigate the operating characteristics and control gain tunning of the Altitude Engine Test Facility(AETF). The simulation duct design involved testing variable spike nozzle and ISO standard choking nozzle to verify the measurements such as mass flow rate and thrust. The simulation duct air flow area was designed to satisfy Ma 0.4 at the aerodynamic interface plane(AIP) at engine design condition. The test conditions for verifying the AETF controls and measurement devices were deduced from 1D analysis and CFD calculation results. The spike-cone driving part was designed to withstand the applied aero-load, and satisfy the axial traversing speed of 10 mm/s at whole operation envelops.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.1
• /
• pp.19-28
• /
• 2021

In rotating detonation engine(RDE), only the detonation wave is moving around the outer wall of the combustor. Neither a mechanical part nor flow is rotating in RDE. Thus, the RDE cross section is not necessary to be circular, but arbitrary closed section is possible. A RDE of tri-arc cross section is designed and As an example of an arbitrary cross sectioned RDE, a RDE of tri-arc cross section is designed in this study, and operational and performance characteristics were examined experimentally. The rotation of the detonation wave is confirmed by dynamic pressure sensor and high-speed camera, while the characteristics of the detonation wave were investigated at the concave and convex surfaces. In the present study, the thrust level of 17.0 N to 96.0 N was obtained depending on the mass flow rate.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.2
• /
• pp.88-97
• /
• 2021

The controller of the gas turbine engine is a component that needs to be developed for the development of the gas turbine engine because it is impossible to get the technology transferred from the engine manufacturer due to the import and export regulation. As a part of the engine control logic research, the Korea Aerospace Research Institute conducted a failure diagnostic research using a small gas turbine engine. Before simulating the engine fault, the ground test was performed to analyze normal behavior and performance of engine. Afterwards, the control logic analysis test equipment was established to simulate various engine fault. It is intended to provide background knowledge to engine control logic research for various engine failure conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.78-84
• /
• 2020

The performance of pintle thruster is analyzed by using the pintle thruster performance analysis model which integrating the element models introduced in Part I. To verify the performance analysis, the results of the developed program are compared with the experimental data of kerosene/hydrogen peroxide liquid pintle thrusters. Based on the results, the characteristics of the pintle thruster are analyzed. The sensitivity analysis is performed to investigate the effect of thruster shape and operation parameters on performance characteristics using both OAT and scatter plot methods. The four performance parameters such as droplet diameter, film flow rate, O/F ratio, and nozzle throat diameter are evaluated to investigate their effects on characteristic speed, combustor pressure, and specific thrust.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.61-68
• /
• 2020

7-tonf turbopump real-propellant tests in Naro Space Center were conducted and high-frequency signals from an accelerometer and pressure sensors installed on the casing and the inlet/outlet pipeline of LOX pump were analyzed to estimate the structural and hydrodynamic stabilities. Waterfalls, frequency spectrums and RMS(Root Mean Square) values of the measured signals were calculated and characteristic instability frequencies by the rotating cavitation and the rear floating ring seal(F.R.S) were investigated. Static pressures of the inlet/outlet pipeline and an acceleration of the pump casing are strongly affected on pressure fluctuation induced by the rear floating ring seal in the leakage path. Despite the acceleration RMS value seems totally small, the rotating-speed-related synchronous frequency affecting the shaft instability is distinctly observed in the frequency contour.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.1
• /
• pp.12-18
• /
• 2021

In this study, the performance modeling of MT30 gas turbine engine is performed. The design point is determined, and the component performance maps to which the scaling technique is applied are generated using standard maps provided by the commercial program. Off-design point performance analysis is performed with the generated performance model, and this is compared with the performance deck data of the engine. It is confirmed that the data of the performance maps generated by the one-point scaling method had some errors from the performance deck data, and it is determined that correction is necessary to increase the accuracy of the performance model. Therefore, the off-design point analysis is performed by creating the correction performance model in a manner that obtains the scaling factors for each operating point(off-design point) according to the high pressure spool speed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.2
• /
• pp.1-11
• /
• 2021

The cavity inside the combustor increases the mixing efficiency of fuel and air by inducing a oscillation of the flow and the recirculation area with a low speed, and enables continuous combustion by maintaining the flame. In this study, the characteristics of the internal flow by change in the shape parameters of the cavity were analyzed through experiments and two-dimensional computational analysis. It was observed that the flow in the supersonic combustor was greatly influenced by various shape parameters of cavity besides L/D. Even with the same L/D, it was confirmed that the flow type varies depending on the depth of the cavity, either open or closed type, and the aft ramp angle of the cavity and the height of the combustor also affect the flow characteristics. As a result, the change in the shape parameters of the cavity had a great influence on the total pressure loss.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.4
• /
• pp.53-58
• /
• 2021

Based on surrogate model, a hydrocarbon mixture was analyzed by visualizing the impinging break up mechanism in subcritical and supercritical conditions. Decane and methylcyclohexane with different critical pressures and temperatures were selected as experimental fluids. The impinging injector was installed inside the chamber, and the spray was visualized through a speed camera in subcritical and supercritical conditions. The injection condition of the mixture and chamber was kept constant at Pr(P/P_c) = 1, and Tr(T/T_c) was increased from 0.48 to 1.02. As Tr increased, the spray angle increased, and the sheet length decreased as the properties of the mixture reached each critical point. In addition, when the mixture approached the near critical point, it was shown that the change in density gradient was largely observed out of the impinging break up mechanism.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.3
• /
• pp.134-140
• /
• 2022

Ship local structure sometimes experiences severe vibration due to the resonance with an excitation force generated by the propulsion system. In that case, the installation of dynamic vibration absorber such as Tuned Mass Damper (TMD) on the structure can be considered as an effective alternative countermeasure to reduce the troublesome vibration if structural modification or change of excitation frequencies is difficult. Meanwhile, the conventional optimal design method of TMD premises the target structure exposed on an excitation force without the constraint of its magnitude and frequency range. However, the frequencies of major ship excitation forces due to propulsion system are normally bounded and its magnitude is varied according to its operation speed. Hence, the optimal design of TMD to reduce the resonant vibration of ship local structure should be differently approached compared with the conventional ones. For the purpose, this paper proposes an optimal design method of TMD considering maximum frequency and magnitude variation of a target harmonic excitation component. It is done by both lowering the resonant response at the 1st natural frequency and locating the 2nd natural frequency over maximum excitation frequency for the idealized 2 degree of freedom system consisted of the structure and the TMD. For the validation of the proposed method, a numerical design case of TMD for a ship local structure exposed on resonant vibration due to a propeller excitation force is introduced and its performance is compared with the conventionally designed one.

• Journal of Advanced Navigation Technology
• /
• v.27 no.1
• /
• pp.96-101
• /
• 2023

In this work, an energy harvester (EH) on the rotating shaft has been proposed for a wireless sensor system (WSS) applications. The EH was designed and implemented to the shaft with a diameter of 20 cm to continuously power a wireless sensor system (WSS). The rotor has coils wound in pairs on seven U-shaped cores attached to the shaft. The stator consists of eight pairs of magnets attached to eight I-cores and they are fixed to an outer fixture. The generated power of the EH was investigated as function of the air gap between the rotor and stator, the number of turn of coils, and shaft speed. The fabricated EH produced power up to 2.87 W at 300 rpm and the 3 mm air gap.