• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.332-335
• /
• 2003

Particle size and piezoelectric characteristics of PNW-PMN-PZT ceramics with the variations in attrition milling conditions were investigated for the piezoelectric transformer application. Particle size and distribution were decreased with increasing milling time. Dielectric constant (${\varepsilon}r$), electromechanical coupling factor (kp), mechanical quality factor (Qm) and density showed the optimum value of 1563, 0.53, 2342, 7.63, respectively at 7h milling time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.290-291
• /
• 2007

In this study, in order to develop the low temperature sintering multilayer piezoelectric actuator, PZW-PMN-PZT system ceramics were manufactured according to variation of sintering aids. At the sintering temperature of $900^{\circ}C$, $0.3wt%Li_2CO_3$, $0.2wt%Bi_2O_3$ and 0.2wt%CuO added specimen showed a maximum value of kp = 0.552, $d_{33}\;=\;344pC/N$ and Qm = 1320, respectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.407-412
• /
• 2004

본 연구에서는 PMN-PT bimorph actuator를 이용하여 초소형 광디스크 드라이브용 광픽업 구동기를 제작하였다. 최근에 휴대용 기기에서의 고용량 정보 저장기기에 대한 필요성이 대두됨에 따라 착탈식이 가능한 수 기가급 초소형 광디스크 드라이브가 개발중에 있다. PMN-PT는 약 1.5kV/cm 이하의 전기장에서는 PZT같은 압전 소자와 마찬가지로 입력 전압에 대한 변형률이 선형성을 나타내는데, 사용된 PMN-PT는 PZT의 약 3배 가까운 압전 상수값을 나타내었다. 보 끝단에 외부 힘이 작용할 때 PMN-PT bimorph 구동기가 낼 수 있는 수직 방향의 힘과 변위에 대해서 일반적인 적층 형태로 이론적인 해석을 수행 하였다. 그리고 이 bimorph로 구동될 Cymbal 형태의 변위 확대 기구의 변위에 대한 이론적인 모델을 제시하고, 이를 이용하여 2개의 bimorph로 2축을 동시에 구동하는 픽업 구동기를 제작하였다. 3개의 제작된 prototype으로 실험을 수행하여 예상 변위량과 잘 일치함을 보였다. 또한, 상용 해석 프로그램인 Matlab과 Ansys를 이용하여 Cymbal 확대 기구의 여러 파라미터에 따른 구동 성능의 민감도를 확인해 보았다.

• ETRI Journal
• /
• v.31 no.6
• /
• pp.688-694
• /
• 2009

In this paper, we present the results of a preliminary study on the piezoelectric energy harvesting performance of a Zr-doped $PbMg_{1/3}Nb_{2/3}O_3-PbTiO_3$ (PMN-PZT) single crystal beam. A novel piezoelectric beam cantilever structure is used to demonstrate the feasibility of generating AC voltage during a state of vibration. The energy-harvesting capability of a PMN-PZT beam is calculated and tested. The frequency response of the cantilever device shows that the first mode resonance frequency of the excitation model exists in the neighborhood of several hundreds of hertz, which is similar to the calculated value. These tests show that several significantly open AC voltages and sub-mW power are achieved. To test the possibility of a small scale power source for a ubiquitous sensor network service, energy conversion and the testing of storage experiment are also carried out.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.407-407
• /
• 2008

무기EL 디스플레이는 고체재료에 전계를 가했을 때 발광하는 현상을 이용한소자로서, 급속도로 발전을 거듭하고 있으나, 유전체층에 강한전계를 가하여 발광하여야 하므로 낮은 Breakdown voltage와 효율의 한계로 인하여 휘도가 낮고 풀 컬러화 디스플레이 등 의 응용에는 적용되고 있지 못하는 실정이다. 본 연구에서는 강유전체 Perovskite 구조를 가지는 ABO3 물질 중 PMN(Lead Magnesium niobate) 과 PZT (Lead Zirconate titanate) 후막을 제조하여 Inorganic EL(Electro Luminance)에 적용하고 소자의 광전특성을 평가하였다. 소자에 사용된 기판은 고온소성에 알맞은 알루미나(Al2O3)기판을 채택 하였으며, 그 위 하부전극으로는 고온소성에 따른 화학적 안정성이 우수한 Au전극을 Screen Printing 하였다. 제조 되어진 PMN후막 페이스트는 PMN(Pb(Mg1/2 Nb2/3)O3) + Glass Frit(Pb-Zn-B) + BaTiO3(99.99%) 로 합성되었으며 하부전극위에 인쇄하였다. 그 다음 PZT sol-gel을 Spin coating으로 도포 하였다. 형광체로 ZnS:Cu.Cl 을 Screen Printing을로 형성하였으며, 평탄화를 위하여 유기물 충을 Screen Printing 공정으로 성막 하였다. 상부전극으로는 DC sputter로 ITO를 증착하여 EL소자 완성 후 Spectro - Chroma meter로 소자특성을 측정하였다. 평탄화를 통한 유기물층에 변화되는 Capacitance를 Oscilloscope로 전압 전류 pulse의 변화에 따른 opto-electronic 특성을 평가하였다.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.3
• /
• pp.175-182
• /
• 2016

For application to several MHz photoacoustic imaging systems, a needle hydrophone was designed and fabricated by using PMN-PZT piezoelectric single crystal, and its characteristics were evaluated through comparison with a commercial PVDF(Polybinylidene Fluoride) hydrophone of which receiving sensitivity is known. The simulation using the KLM model results show that the peak receiving impulse response for $50{\Omega}$ terminating impedance of the fabricated hydrophone is -261.6 dB re $1V/{\mu}Pa$ and the frequency response is relatively flat over 2 ~ 12 MHz with fluctuation less than 5 dB. The measurement results using tone burst signals also show that it has higher (ave. 10.9 dB) sensitivity than the commercial hydrophone in 2 ~ 8 MHz, and the receiving sensitivity of $-255.8{\pm}2.8$ dB re $1V/{\mu}Pa$ was measured for the fabricated hydrophone. In addition, it is known that the photoacoustic signals and the image of a hair obtained by a mechanical scanned photoacoustic imaging system with the fabricated hydrophone were bigger and better than those obtained with the commercial hydrophone.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.222-223
• /
• 2008

Recently, piezoelectric transformer is applied to wide fields. Multi layer piezoelectric transformer has the advantage of high step up ratio, high electromechanical coupling coefficient(Kp) and high mechanical quality factor(Qm), however it shows the peeling-phenomenon of electrode, and high price due to high sintering temperature. Therefore this study focus on the method for fabrication of high power rosen type piezoelectric transformers. The composition of $0.01Pb(Ni_{1/3}Nb_{2/3)O_3$ - 0.08Pb$(Mn_{1/3}Nb_{2/3})O_3$-0.91Pb$(Zr_{0.505}Ti_{0.495})O_3$(abbreviated as PNN-PMN-PZT) ceramics is employed for this study.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.3
• /
• pp.127-132
• /
• 2005

Transducers for implantable hearing aids need to be small and to have good performance in frequency responses and vibration properties. From this viewpoint, we Proposed a multi-layer actuator with the piezoelectric single crystal, PMN-PT. for the implantable hearing aid. and verified its adequacy through finite element analyses and experiments. PMN-PT multi-layer actuator samples were fabricated by stacking fourteen layers of the PMN-PT crystal. Each layer were $0.2{\cal}mm$ thick and the actuator sample was $2.8{\cal}mm$ thick in total. We evaluated the performance of the PMN-PT actuator through impedance analyses and vibration displacement measurements, and compared the result with that of a PZT actuator. Results of all the process confirmed the feasibility of the PMN-PT actuator as a good transducer for an implantable hearing aid.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.4
• /
• pp.313-320
• /
• 2007

Recently, a new class of single-crystal piezoelectric materials such as lead metanibobate doped with lead titanate (PMN-PT) has been synthesized and were found to further enhance the electro-mechanical coupling factor compared to piezo-ceramic materials. This paper describes fabrication and evaluation of PMN-PT single crystal ultrasonic transducers for contact measurement of stainless steel that is one of the highly attenuative materials. The design conditions for ultrasonic transducer such as front matching layer between test materials and piezo-material and backing materials were investigated based on the simulation results by KLM model. The PMN-PT single crystal ultrasonic transducers with centre frequencies at 1 and 2.25 MHz were fabricated and their performances were evaluated.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.04a
• /
• pp.179.2-179
• /
• 2003