• Transactions on Electrical and Electronic Materials
• /
• v.17 no.4
• /
• pp.204-207
• /
• 2016

Experimental study of UV-irradiated O₂/H₂ gas phase cleaning for PMMA (Polymethylmethacrylate) removal is carried out in a load-locked reactor equipped with a UV lamp and PBN heater. UV enhanced O₂/H₂ gas phase cleaning removes polymethylmethacrylate (PMMA) better at lower process pressure with higher content of H₂. O₂ gas compete for UV (184.9 nm) absorption with PMMA producing O₃, O(¹D) and lower dissociation of PMMA. In our experimental conditions, etching reaction of PMMA at the substrate temperature between 75℃ and 125℃ had activation energy of about 5.86 kcal/mol indicating etching was controlled by surface reaction. Above the 180℃, PMMA removal was governed by a supply of reaction gas rather than by substrate temperature.

• Tuberculosis and Respiratory Diseases
• /
• v.61 no.2
• /
• pp.184-188
• /
• 2006

Percutaneous vertebroplasty consists of the percutaneous injection of polymethylmethacrylate (PMMA) cement into a collapsed vertebral body in order to obtain pain relief and mechanically strengthen the vertebral body. This procedure is now extensively used in treating osteoporotic vertebral compression fracture. It is an efficient treatment, but it is not free of complications. Most complications after vertebroplasty are associated with PMMA leakage. Pulmonary embolism of PMMA is rare, but this can occur when there is a failure to recognize venous migration of cement early during the procedure. We encountered a case of a patient with asymptomatic pulmonary embolism because of PMMA after percutaneous vertebroplasty. Chest X-ray and CT scanning revealed numerous tubular branching opacities that corresponded to the pulmonary vessels at the segmental and subsegmental levels.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.79-85
• /
• 1997

In order to improve the surface characteristics of polymethylmethacrylate(PMMA), oxide thin film coatings were applied using the sol-gel dip-coating technique. The $Si(OC_2H_5)_4$, tetra-ethyl-ortho-silicate(TEOS) was used as a starting material for $SiO_2$ coating. The hardness of the alkoxy-derived oxide-coated PMMA was increased from 190 MPa for non-coated PMMA with increasing film thickness. By optimizing the heating conditions and the hydrolysis conditions, a maximum apparent hardness obtained In the present study was achieved 310 MPa using the withdrawal velocity of 5cm/min and heat treatment at $90^{\circ}C$ for 5 hours, which is about 1.6 times larger than that of uncoated PMMA.

• Analytical Science and Technology
• /
• v.19 no.6
• /
• pp.468-472
• /
• 2006

This paper was described that the preparation of polymetylmethacrylate (PMMA) microsphere and coating of vitamin C onto surface of the prepared PMMA microsphere for application of cosmetic materials. The PMMA microsphere with various sizes can be obtained by change of reaction condition such as reaction temperature and reaction time. The coating of vitamin C on the surface of PMMA microsphere by using cyclodextrin as binder can be achieved to 30 wt-% in water/ethanol mixture. The vitamin C coated with cyclodextrin was stabilized during 56 days at $40^{\circ}C$. The color of the coated Vitamin C was changed from white to dark yellow after 14 days at $40^{\circ}C$. The vitamin C coated with cyclodextrin on the surface of PMMA microsphere can be sufficiently used for cosmetic materials.

• Fibers and Polymers
• /
• v.5 no.3
• /
• pp.239-244
• /
• 2004

Solution-cast films of polymethylmethacrylate (PMMA) and polyurethane (PU) containing polymeric styryl dye up to 5 % by weight were prepared to investigate their acid-sensitivity and mechanical and thermal properties. Original red samples due to styryl dye turned out yellow very rapidly as they were exposed to acid vapor of hydrochloric acid or p-toluenesulfonic acid. According to UV/VIS spectroscopic measurements, characteristic peak intensities near 430 nm and 520 nm increased or decreased relatively with exposed amounts of acid, respectively. Both PMMA and PU samples showed uniform color distribution due to a good miscibility between polymer and dye which can be evidenced by measurements of glass transition temperature. No significant difference in acid-sensitivity was found between PU and PMMA except relative absorbance. However, dependence of their mechanical properties on dye content was somewhat different with PU or PMMA. In case of PMMA, modulus and breaking stress increased up to about 50 % with increasing dye content, whereas those of PU samples showed only slight increase. It was ascribed to whether the matrix polymer was in the glassy or rubbery state.

• Polymer(Korea)
• /
• v.26 no.4
• /
• pp.462-467
• /
• 2002

Blends of polymethylmethacrylate (PMMA) with polyvinylidenefluoride (PVDF) were prepared by melt mixing and investigated for optical waveguide devices by using hot embossing process. The glass transition temperatures ($T_g$) of the blends were decreased with increasing PVDF contents. However, the crystalline of PMMA/PVDF blends was not appeared by DSC and XRD due to miscibility between PMMA and PVDF. Shear viscosities and refractive indices of the blends were decreased with increasing PVDF contents. Optical transmittances and absorption losses of the blends were improved with increasing PVDF contents. This is due to a decreasing of polarizability of molecules by fluorine molecule in the PVDF.

• Membrane Journal
• /
• v.18 no.3
• /
• pp.219-225
• /
• 2008

In this research, polydimethylsiloxane-polymethylmethacrylate (PDMS-PMMA) block copolymer was synthesized from polydimethylsiloxane (PDMS) and methylmethacrylate (MMA) monomer using atom transfer radical polymerization (ATRP). The synthesis characterization of the PDMS-b-PMMA copolymer membrane was carried out by a FT-IR, $^1H$-NMR, GPC and DSC. The permeabilities of nitrogen and hydrogen gases were observed being $1.2{\sim}l.5$ barrer and $6.2{\sim}10.5$ barrer, respectively. Simultaneously, selectivities of hydrogen against nitrogen were $5.3{\sim}6.9$. The permeability and selectivity of PDMS-b-PMMA copolymer membrane were showed lower than the PDMS membrane, but higher than the PMMA membrane.

• Journal of Korean Neurosurgical Society
• /
• v.30 no.3
• /
• pp.272-277
• /
• 2001

Objective : Polymethylmethacrylate(PMMA) is often used to reconstruct the spine after total corpectomy, but the exothermic curing of liquid PMMA poses a risk of thermal injury to the spinal cord. The purposes of this study are to analyze the heat blocking effect of pre-polymerized PMMA sheet in the corpectomy model and to establish the minimal thickness of PMMA sheet to protect the spinal cord from the thermal injury during PMMA cementation of vertebral body. Materials & Methods : An experimental fixture was fabricated with dimensions similar to those of a T12 corpectomy defect. Sixty milliliters of liquid PMMA were poured into the fixture, and temperature recordings were obtained at the center of the curing PMMA mass and on the undersurface(representing the spinal cord surface) of a prepolymerized PMMA sheet of variable thickness(group 1 : 0mm, group 2 : 5mm, or group 3 : 8mm). Six replicates were tested for each barrier thickness group. Results : Consistent temperatures($106.8{\pm}3.9^{\circ}C$) at center of the curing PMMA mass in eighteen experiments confirmed the reproducibility of the experimental fixture. Peak temperatures on the spinal cord surface were $47.3^{\circ}C$ in group 2, and $43.3^{\circ}C$ in group 3, compared with $60.0^{\circ}C$ in group 1(p<0.00005). So pre-polymerized PMMA provided statistically significant protection from heat transfer. The difference of peak temperature between theoretical and experimental value was less than 1%, while the predicted time was within 35% of experimental values. The data from the theoretical model indicate that a 10mm barrier of PMMA should protect the spinal cord from temperatures greater than $39^{\circ}C$(the threshold for thermal injury in the spinal cord). Conclusion : These results suggest that pre-polymerized PMMA sheet of 10mm thickness may protect the spinal cord from the thermal injury during PMMA reconstruction of vertebral body.

• The Korean Journal of Pain
• /
• v.13 no.1
• /
• pp.126-129
• /
• 2000

Age-related osteoporotic compression fractures occur frequently in old aged group recently. Percutaneous vertebroplasty has recently been introduced as a therapeutic method for the treatment of pain associated with osteoporotic vertebral compression fracture. Percutaneous intravertebral injection of PMMA (polymethylmethacrylate) results in marked reduction in pain and morbidity. Among complications during vertebroplasty with PMMA, pulmonary embolism is repotred occasionally but the reports about hypotension are not common. This case is a report of a patient whom significant hypotension occured during percutaneous vertebroplasty.

• Applied Chemistry for Engineering
• /
• v.21 no.3
• /
• pp.317-322
• /
• 2010

In this study, poly(methyl methacrylate) (PMMA) was treated with changing mixing ratios of $F_2$ and $O_2$ using oxyfluorination method for hydrophilic modification of PMMA film. For the characterizations of oxyfluorinated PMMA surface, contact angle, surface free energy, X-ray photoelectron spectroscopy (XPS) and optical transmittance (UV-vis) were carried out. After the oxyfluorination, PMMA surface became more hydrophilic showing the decrease of water contact angle from $69^{\circ}$ to $44^{\circ}$. So, surface free energy of oxyfluorinated PMMA film was increased from 46 to $58\;mN\;m^{-1}$. These results are attributed to hydrophilic functional groups such as hydroxyl group formed oxyfluorination method on the PMMA surface. From XPS results, it was confirmed that O/C concentration ratio on the surface of PMMA was increased, the amount of C-OH bonding which shows hydrophilicity was also largely increased from 6.7 to 24.8% with increasing fluorine partial-pressure via the oxyfluorination, The oxyfluorination conditions, room temperature, 1 bar with one mixture ratio of $F_2$ to $O_2$ had little influence on optical transmittance properties of PMMA film but enhanced its surface hydrophilicity. This result suggests that oxyfluorination method could be useful to change hydrophobic PMMA surface to hydrophilic.