• Journal of the Korea Furniture Society
• /
• v.16 no.2 s.30
• /
• pp.59-65
• /
• 2005

As physical condition of students improves, there is a need to develop human body-friendly desk and chair for students. In this study, desks and chairs were manufactured with curved veneer lamination under high frequency heating and pressing, using ten wood species such as Japanese red pine, Korean pine, pitch pine, Japanese larch, yellow poplar, black locust, oak, radiata pine, beech, and birch. The performance of these products were evaluated. The results obtained were summarized as follows; With high frequency heating, the turned lamination of veneers with full size sheet ($3{\times}6\;feet$) prepared by rotary lathe peeling was successfully applied for making the members of desk top, leg frames of desk and chair. Bending strengths of desk tops were relatively greater for yellow poplar, black locust and red pine, which were similar to those of beech and birch. Bending strengths of desk legs were classified into greater species group (red pine, yellow poplar, larch) and lower species group (radiata pine, Korean pine, pitch pine). Compressive strengths of chair legs in parallel direction to the lamination were greater in black locust and larch. On the other hand, differences between outer and inner gap at the top and drawer bottom of desk top were rather larger for the laminations of birch and beech, and less for those of yellow poplar and pitch pine, showing greater stability of open drawer space. In results, yellow poplar, larch, pitch pine and red pine showed good appearance and strength properties at the curved veneer lamination. Accordingly, it was believed that these domestic woods were able to substitute for birch which was being imported for the use of veneer-laminates type furniture.

• Korean Journal of Medicinal Crop Science
• /
• v.23 no.1
• /
• pp.43-48
• /
• 2015

This study was carried out in order to investigate the photosynthesis response and leaf characteristics of Peucedanum japonicum growing in forest farming. The experiment was performed by leaf mold (pine tree and chestnut tree) and shading levels (0%, 35%, 50% and 75% shading). Light relative intensity was 100% (full sunlight), 60.3% (35% shading), 35.1% (50% shading), and 17.4% (75% shading) respectively. Light response curves of pine-leaf mold and chestnut-leaf mold were the highest in control (full sunlight) and these were getting lower in the higher shading level. Photosynthesis capacity and light saturation point were indicated higher in chestnut-leaf mold within the same shading level. As the shading level increased, maximum photosynthesis rate decreased. And apparent quantum yield was not indicated statistically significant difference from all treatment. Leaf area, leaf length and leaf width were significant higher in 35% shading and control under chestnut-leaf mold in all treatment. As the shading level increased, LAR (leaf area ratio), SLA (specific leaf area) and SPAD value decreased in pine-leaf mold and chestnut-leaf mold. As a result of surveying the whole experiment, P. japonicum is judged better growth and higher yield by maintaining 35% shading (relative light intensity 60%) under chestnut-leaf mold in forest farming.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.6
• /
• pp.41-48
• /
• 2008

The required energy for the heat treatment of pine log was evaluated in this study. A proper heat treatment of pine log infected by pinewood nematode (Bursaphelenchus xylophilus) can prevent spreading of the infection by pinewood nematode and make the infected pinewood valuable again. The FAO (Food and Agriculture Organization of the United Nations) heat treatment standard for various types of infected wood for which a heat treatment of the core part of the wood is necessary is 30 minutes at $56^{\circ}C$, taking into account the international standards for phytosanitary measures (ISPM No. 15). In this study, the energy consumption during the heat treatment was separated into two kinds of energy, initial energy for heating kiln drier and to reach set point temperature and relative humidity and the required energy supplementing heat loss. The initial required energy per unit time is greater than that during the treatment. The energy consumption per unit time varied little during the heat treatment. As a result, the set point relative humidity with set dry bulb temperature and density of wood dependent on moisture content are very important factors to change energy consumption in the experiment. The heat treatment at higher temperature and higher humidity levels requires more energy consumption but less treatment time. It is expected that a more effective energy program could be planed for the heat treatment of pine log through this study.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.3
• /
• pp.243-249
• /
• 2017

This study was performed to find out the optimum adhesive conditions on manufacturing a cross-laminated timber (hereinafter CLT) with using domestic Korean Pine (Pinus koraiensis). The adhesive conditions including a applied amount of the glue and a Pressure are the one of the most important key factors on establishing CLT production process. The shear strength was examined with differing the adhesive conditions while using Phenol Resorcinol Formaldehyde Resin Adhesive (PRF resin). The optimum adhesive conditions was confirmed to be: glue spread of $250g/m^2$ and Pressure of 0.8 MPa respectively. The grain directions of glued specimens were also considered, perpendicularly bonded and parallelly bonded groups. Shear strength of the former group showed lower values than the latter group which is considered to be the effect of a rolling shear. Meanwhile the shear strength of both group satisfied the Korean Standard (KS F 3021) and the European Standard (EN 14080 and EN 16351). The results derived from this study can be used as the basic data for manufacturing the CLT with domestic Korean Pine. And additional researches for the other species including domestic Korean Larch and Pitch Pine is also now being performed.

• Journal of Korean Society of Forest Science
• /
• v.97 no.6
• /
• pp.561-564
• /
• 2008

Pinus densiflora(red pine) stands in Korea have been faced with the serious threat by pine wilt disease caused by Bursaphelenchus xylophilus (nematodes). It is not easy to early detect and prevent the infected trees because those cannot be visually identified during the initial phase of infection. Red pine is usually infected by B. xylophilus from May to July and can be just visually detected in October or November. While the infected trees are wilted, the spectral value of Near Infrared (NIR) is supposed to be decreased. Based on this phenomena, in this paper, the vegetation vitality change of infected trees was analyzed using vegetation indices. Spectral values of Red, Green and NIR had been acquired monthly by a portable NIR camera in the same place of red pine stands infected by pine wilt disease. It could be proven that the vegetation index, or vegetation vitality of damaged trees starts to decrease from June, in the early infecting phase.

• Journal of Korean Society of Forest Science
• /
• v.26 no.1
• /
• pp.43-47
• /
• 1975

Forecasting of emergence period of the pine gall midge (Thecodiplosis japonensis U. et I.) is important for the chemical control of the pest. In order to determine the phenosignal of the emergence period of the pine gall midge, the flowering time of black locust (Robinia pseudoacacia L.) at Seoul, Gwangnug, Jounju and Gyungju districts in Korea was investigated. 1. The emergence period of the pine gall midge lasted from end of May until end of June. The emergence of the pine gall midge coincided with the beginning of flowering of black locus at every districts in Korea. 2. The peak of emergence of the pine gall midge lasted from the full blooming period until the end of the flowering period of the black locust. 3. The period of adult emergence of pine gall midge was also found to be associated with the full blooming period of Viburnum sargentii (Caprifeliaceae). Rosa mulliflora (Reseaceae) and Iris ensata (Iridaceae) at Seoul in Korea.

• Journal of Korean Society of Forest Science
• /
• v.9 no.1
• /
• pp.45-48
• /
• 1969

The objective of this research was to investigate the seasonal trends in the population of the larvae of the Pine gall-midge in the spring at field. 1. The comparative ratio in the number of larvae of the Pine gall-midge was 100 in early spring, 29 at April 15th and 10 at May 4th. 2. Probably, the seasonal decrease in the number of larvae at field may be due to the gradual rising in the temperature and decreasing the relative Humidity season the experiment was conducted. 3. Water selection method gave best results in collecting the larvae from soil.

• Journal of Korean Society of Forest Science
• /
• v.76 no.4
• /
• pp.330-337
• /
• 1987

Megagametophyte tissues from seeds of 45 loblolly pine clones were subjected to horizontal starch-gel electrophoresis. The resulting gels were tested for activity of five enzyme systems (GOT, SDH, PGM, MDH, and AP). Isozymes observed were under control of 11 loci. All 45 clones could be identified with unique genotypes at above 10 loci.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.13 no.1
• /
• pp.28-34
• /
• 2010

The spatial distribution characteristics of damaged trees by the pine wilt disease appear scattered spots spreading from single dead trees. That is the reason why it is difficult to early detect damage and to prevent from extensive damage. Thus, it is very important to forecast and analyze the damage occurrences, to establish strategies for prevention, and to supervise them. However, conventional survey which observes around roads or residential areas by naked eyes was impossible to investigate completely, missing target areas and dangerous areas. Therefore, aerial forecasting techniques on the damaged area were developed using GIS, GPS, and helicopters for an accurate observation of systematic and scientific approach in this study. Moreover, advantages of the techniques application were confirmed to survey 972 dead tree samples at 349 position-coordinates in 32 cities (about $28,810km^2$), 2005. This study is expected to apply widely to find dead trees and the causes, particularly by pine wilt disease.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.2
• /
• pp.108-116
• /
• 2010

This paper explains the effects of wood drying on treatability (as determined by water uptake) of Japanese red pine (Pinus densiflora S. et Z.) at the sevenmoisture content (MC) levels above and below the fiber saturation point (FSP). According to the experimental results, it was found that water uptake (as the percentage of void volume filledwith distilled water, VVF%) was influenced by level of moisture content and percentage of void volume filled was improved effectively by kiln drying process. A significant relationship between moisture content and treatability was established. Permeability and liquid uptake were decreased above the FSP due to the effect of the less void space available in wood. Even though increased liquid uptake was observed at lower moisture content, no significant differences was observed moisture content below 20%. Therefore, this species need to be initially dried below FSP before treated with liquids. But drying moisture content below 10% might not be economical for the commercial purpose comparing drying the wood between 10 and 20% moisture content. The result of this study inferred that the treatability of pine wood can be improved by reducing the moisture content up to a certain level of 10~20% for allowing better performance.