• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.1
• /
• pp.136-142
• /
• 2005

In this paper, we wrote about the basic experimentation of Optical CT's temperature characteristic to measure high-current in a super-high-voltage electric power equipment which is using Faraday effect. We used the 1310[nm] Laser Diode as the light source and PIN Photodiode as receiver. For the transmission line of light, we used 30[m] single mode fiber which could maintain the state of polarization in the optical fiber. For the experiment, the temperature transformation device make by aluminium. the The range of current was from 400[A] and 1300[A] and the range of temperature was from $-40[^{\circ}C]\;to\;50[^{\circ}C]$. In a same experimental condition, magnitude increased input current increase follow by increasing proportion of input current.

• Korean Journal of Optics and Photonics
• /
• v.11 no.5
• /
• pp.306-311
• /
• 2000

This paper deals with the development of Laser Doppler Vibrometer (LDV) that can mea~ure the tlequency and amphlude of the ultrasonic vibralion. Hc-Ne laser (632.8 om) is used as a light source, and Michelson interferometer in winch frequency of the objective beam is shIfted by Bragg cell IS adopted The frequency modulated signal centered at 40 MHz flom the PIN diode IS amplified. down-col1vel1ed to 2.5 MHz, filtered and digiLized. The voltage output that is proportional to the velocity of the vibratwg surface is obtawed using digItal PLL. A microprocessor is used to extract the frequcncy aud amplitude of the vibratIOn from the voltage output. It is found that the developed LDV can measure up to 300 kHz vibratIOn and the mlillmUITI measurable amplitude is I nm at 300 kHz. We believe thatlhis LDV can be used to measure the vibratIOn of the heavy electric maclllnery and micro-size structures. tures.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.4 s.95
• /
• pp.397-401
• /
• 2005

In this paper, a slot-coupled microstrip antenna with switchable polarization is proposed for the polarization diversity applications in the complicated communication environment. The proposed antenna is fed by a microstrip line through one of two slots located with the interval of $\lambda{g}/4$ in the ground plane. By switching the PIN diode between opened and shorted termination which is located at the tip of the microstrip line, the switching function between horizontal and vertical polarization was confirmed experimentally. The measured resonant frequencies of the fabricated antenna are $2.41\;\cal{GHz}\;2.40\;\cal{GHz}$ and the cross polarization levels are $19\;\cal{dB},\;23\;\cal{dB},\;the\;-10\;\cal{dB}$ return loss bandwidths are $95\;\cal{MHz}\;100\;\cal{MHz}$ in horizontal and vertical polarization, respectively, and the antenna gain is almost $6\;\cal{dBi}$.

• Journal of Sensor Science and Technology
• /
• v.2 no.1
• /
• pp.75-80
• /
• 1993

This study describes a non-invasive optical sensor and system in order to obtain oxygen saturation of blood, in-vitro. The sensor contains LED 665nm and 805nm of wavelength for light source and PIN photodiode for light detector in flat pack. The sensor system for measurement of oxygen saturation has breadboarded, including signal amplifier, filter, displayer, A/D converter, microprocessor and memory. Experimental set-up for non-invasive measurement of oxygen saturation in-vitro was done. When the variation of oxygen saturation is compared with that of each wavelength, the variation of 665nm is more than that of 805nm by five times. As oxygen saturation varies from 100% to 60%, and the reflection ratio (R805/R665) is changed linearly. The oxygen saturation in $100%{\sim}60%$ range can be measured with about 5% resolution by the developed sensor, such that if this sensor connects with the main artery and vein, the artificial heart can be controlled rapidly and precisely from measurement of the sensor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.6
• /
• pp.1170-1174
• /
• 2009

Two frequency-reconfigurable antennas have been designed and combined in a space with limited volume, i.e., 40mm ${\times}$ 20mm ${\times}$ 6mm. Each antenna can be reconfigured to operate at different frequency bands depending on the state of an embedded switch, which is implemented using a PIN diode. The first antenna can be switched between 0.82GHz ${\sim}$ 0.96GHz band (GSM/ CDMA) and 1.7GHz ${\sim}$ 2.17GHz band (DCS/ PCS/ WCDMA), which are cellular bands. The second antenna can be switched between 3.4GHz ${\sim}$ 3.6GHz band (mWiMax) and 2.3GHz ${\sim}$ 2.5GHz, 5.15GHz ${\sim}$ 5.35GHz bands (WiBro/ WLAN 11a/b/g/n), which are connectivity bands. The proposed combined antenna operates both over cellular bands and connectivity bands concurrently. The choice of the operation bands is made independently by the states of the two switches.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.4
• /
• pp.241-246
• /
• 2018

In this study, we proposed a wideband frequency tunable metamaterial absorber using a switchable ground plane (SGP). We proposed two fire retardant or flame resistant 4 (FR4) substrate structures for the SGP. An SGP is placed at the middle layer, between the top pattern and the bottom ground plane. The SGP can either be made ground or reactive, by switching the PIN diode ON/OFF. As the frequency is determined by the substrate thickness, the frequency can be switched from the SGP. The proposed absorber is demonstrated by full-wave simulations and measurements. When the SGP is turned on, an absorptivity higher than 90% is achieved from 3.5 GHz to 11 GHz. When the SGP is turned off, an absorptivity higher than 90 % is achieved from 1.7 GHz to 5.2 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.4
• /
• pp.634-641
• /
• 2000

A switchable VCO for DECT handset is designed and fabricated. In dual mode radios, a single VCO is desired to operate at two different frequencies to meet the requirement of two mode(Tx, Rx). The three design types of switchable VCO are switched resonator VCO, switched mode VCO and dual band VCO. In this paper, we use the switched resonator VCO type using pin diode switch to change the total amount of capacitance in the tank circuit. At the bias condition of 3 V and 13mA, the output power and phase noise are better than6.5dBm and -104dBc/Hz at 25khz offset from the carrier, respectively , across the operating frequency range. From these results, the fabricated switched VCO is applicable to the DECT handset.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.982-988
• /
• 2002

This paper summarizes the design concepts and implementation of a Ku-band channel amplifier's engineering model for the communication and broadcasting satellite applications. The selected architecture uses the analog gain control for the FGM(Fixed Gain Mode) and the output level limiting using automatic loop control for the ALC (automatic level control) mode. The Ku-band channel amplifier incorporates several state-of-the-art components including voltage-controlled PIN diode attenuators, and various temperature-compensation circuits. The measured characteristics of the Ku-band channel amplifier are in good agreement with the expected performance. The results show a fixed gain control of 28 dB, and an automatic level control of 16 dB over operating temperature range. The designed engineering model could be used as a channel amplifier for Ku-band communication and broadcasting satellite payload system.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.9
• /
• pp.392-397
• /
• 2003

Reflection type phase shifter with Lange coupler is widely used as a circuit topology to obtain phase shift in broadband operation. The phase shift of 33.75$^{\circ}$ at this type is achieved by simultaneously turning on both 11.25$^{\circ}$ and 22.5$^{\circ}$ . In order to improve the phase accuracy of 33.75$^{\circ}$, this paper proposes the additional circuit which is composed of a GaAs PIN diode and a reactive load. By utilizing MMIC technology. Over the 2-6 GHz band, the measured result of phase difference between the previous circuit and the proposed circuit shows average 4.7$^{\circ}$ on the basis of 33.75$^{\circ}$. Insertion loss and return loss are invariant in comparison with the previous circuit.

• Korean Journal of Optics and Photonics
• /
• v.22 no.4
• /
• pp.191-197
• /
• 2011

In this paper, we have designed an integrated triplexer which is the basic component for a FTTH(Fiber To The Home) system which can transmit CATV and voice/data at the same time in a single fiber. The integrated triplexer can be fabricated with a novel technique of "Micro-Block Stacking (MBS)" method which automatically aligns the optical components in the optical beam pass using accurate ceramic holders. We analyze the displacement of the optical focus according to the tolerances of the component dimensions and the assembly process using code V simulator. For the transmitter, the most serious shift of the focal points is caused by the displacements of the LD spot. So the focal point moves up to $72{\mu}m$ from the center point for ${\pm}25{\mu}m$, ${\pm}25{\mu}m$, ${\pm}30{\mu}m$ displacements. For the receiver the most serious shift of the focal points is caused by the displacements of a 0.8mm ball lens (for the analog receiving part) and a micro ball lens (for the digital receiving part), and the focal point moves up to $55{\mu}$ for ${\pm}55{\mu}m$, ${\pm}5{\mu}m$, ${\pm}55{\mu}m$ micro ball lens displacements.