• Korean Membrane Journal
• /
• v.3 no.1
• /
• pp.51-58
• /
• 2001

The surface of Poly(ether imide) (PEI) membranes has been sulfonated using CIS03H. The resulting membranes were characterized through the analysis of ESCA and contact angle measurements The sulfonated PEI membranes were exposed to gases of $O_2$, $N_2$, and $CO_2$ to measure the permeation rates and ideal separation factors. In addition, the diffusivities and solubilities of individual gases were measured. The diffusivity effect is more dominant than the solubility one on gas transports.

• Membrane Journal
• /
• v.23 no.2
• /
• pp.176-184
• /
• 2013

To investigate the performance of VOC separation, composite hollow fiber membrane was prepared which composed of poly (ether imide) support prepared by phase separation method and poly (dimethylsiloxane) coating active layer. The performances of the membranes for the application of recovery process in terms of their morphology, gas permeance test for $N_2$ and $O_2$ gases. Durability against benzene, toluene and xylene was also investigated. And permeation test for multi-component VOCS through the membrane with different feed concentration and stage-cut were investigated. Permeance of PEI supported membrane and the membranes coated with PDMS decreased from 45,000 GPU to 63 GPU and 49,450 to 30 GPU for $N_2$ and $O_2$, respectively. Recovery efficiency and concentration of VOCs in permeate increased with decreasing stage-cut. VOCs concentration in permeate proportionally increased with increasing feed concentration but concentration ratio and recovery efficiency showed any noticeable changes with feed concentration change.

• The Korean Journal of Rheology
• /
• v.9 no.2
• /
• pp.53-59
• /
• 1997

열방성 액정고분자(LCP)와 polycarbonate(PC) poly(ether imide) (PEI) poly(PEEK), polysulfone(PSF), 그리고 polyarylsulfone(PAS)과의 블렌드에 대한 상용성을 연구하였다. 제조된 블렌드의 상거동에서 액정고분자가 PC-, PEI-, PEEK-, PSF-, 그리고 PAS-rich 상 에 녹아 들어가는 양이 PC, PEI, PEEK, PSF, 그리고 PAS가 액정 고분자 -rich상에 녹아들 어가는 양보다 많음을 알수 있었다. 측정된 블렌드의 유리전이온도 결과로부터 PC, PEI, PEEK와 액정고분자 사이의 상용성이 PSF, PAS와 액정 고분자 사이의 상용성에 비하여 더 좋음을 알수 있었다. 액정 고분자의 이방성을 고려하여 고분자-고분자 상호작용계수($\chi$12)를 결정하였으며, PC, PEI, PEEK, PSF, 그리고 PAS를 포함한 액정 고분자 블렌드에서 $\chi$12는 0.078-0.183으로 나타났다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.116-119
• /
• 1997

In this paper A double-layer organic electroluminescent(EL) device was fabricated using a TPD(N,N'-dipheny] -N,N'-bis(3-methylphenyl)-[1,1'-biphenyl]-4.4'-diamine: aromatic diamine), as a hole-transport material and tris (8-hydroxy quinolinate) aluminum(Alq$_3$) as a an emiting material and its performance characteristics were investigated. structure of devices is ITO/TPD/Alq$_3$/Al. we have fabricated hole transport layer of two types. Doping material of Hole Transport material is Poly(methyl methacrylate)(PMMA) and PEI(Poly-Ether-Imide). Carrier injection from the electrodes to the doped PMMA and PEI layer through the dopants and concomitant electroluminescence from Alq$_3$were observed. Green emission with luminance of 40cd/m$^2$was achieved at a drive voltage of 30V

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.338-345
• /
• 2015

Poly(phenylene oxide) (PPO) and polyether imide (PEI) were sulfonated and aminated to create sulfonated poly(phenylene oxide) (SPPO) and aminated polyether imide (APEI), respectively. Characterization of the SPPO and APEI were performed via measurements of FTIR, thermogravimetry (TGA), swelling degree, ion exchange capacity (IEC), and ion conductivity. Next, the surfaces of these membranes were modified by surface fluorination at room temperature. The surface fluorinated SPPO and APEI membranes underwent characterization again for the mentioned measurements to determine any differences. The 3 types of bi-polar membranes were prepared by varying the IEC of the APEI at a fixed SPPO IEC value, which were applied to the low and high NaCl concentration of feed solution at the different current density, respectively. The hypochlorite concentration derived from the surface fluorinated membranes was dependent on the IEC of the APEI and ranged from 491 to 692 ppm at $80mA/m^2$. At low current density of $5mA/m^2$, the hypochlorite concentrations ranged from 18 to 28 ppm for the 4 hrs surface fluorinated membranes and their durability increased greatly.

• Membrane Journal
• /
• v.23 no.1
• /
• pp.1-11
• /
• 2013

Poly(ether imide) (PEI)-poly(dimethylsioxane) (PDMS) composite membranes and their modules were prepared, which are capable of selective $CO_2$ separation from the mixture gas. The gas flow rate, concentration, recovery ratio of $H_2$ and removal ratio of $CO_2$ outflowing by stage-cut were characterized at $25^{\circ}C$ and the constant pressure. In addition, to increase the recovery ratio of $H_2$, one stage, two stage series connection, and three stages series + parallel connection tests were carried out. When the stage-cut was 0.32 for the three stages connection operation, the concentration $H_2$ of the produced gas and the recovery ratio of $H_2$ was 97% and 85%, respectively. And also the removal ratio of $CO_2$ was 90% was obtained and the recycled gas concentration was similar with that of the feed gases.

• Membrane Journal
• /
• v.25 no.4
• /
• pp.352-357
• /
• 2015

To determine the pervaporation separation characteristics of 1-butanol/water mixtures, PEI/PDMS hollow fiber membrane module commercialized by Airrane Co. was subjected to both lab and pilot tests. The 1% 1-butanol of 1-butanol/water feed mixture was used. The flux of $133g/m^2hr$ and separation factor of 23.4 at $30^{\circ}C$ were obtained whereas the $505g/m^2hr$ and 5.1 were measured at $50^{\circ}C$. When compared with the performance of the hollow fiber PDMS membrane by Nagasep Co., the higher flux of $10{\sim}20g/m^2hr$ was obtained by the module of Airrane Co. In order to realized the durability of Airrane Co. module, the long-term test of 35 days has been conducted and as a result, the flux $510{\sim}520g/m^2hr$ and separation factor 20~25 were maintained with the initial values.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.399-402
• /
• 1998

Electroluminescent(EL) devices based on organic thin films have attracted lots of interests in large-area light-emitting display. One of the problems of such device is a lifetime, where a degradation of the cell is possibly due to an organic layers thickness, morphology and interface with electrode. In this study, light-omitting organic electroluminescent devices were fabricated using Alq$_3$(8-hydroxyquinolinate aluminum) and TPD(N,N'-diphenyl-N,N'-bis(3-methylphenyl(1-1\`-biphenyl]-4,4'-diamine). Where Alq$_3$ is an electron-transport and emissive layer, TPD is a hole-transport layer. The cell structure is ITO/TPD/Alq$_3$/Al and the cell is fabricated by vacuum evaporation method. In a measurement of current-voltage characteristics, we obtained a turn-on voltage at about 9 V. We also investigated stability of the devices using buffer layer with blend of PEI (Poly ether imide) and TPD by varying mot ratios between ITO and Alq$_3$. In current-voltage characteristics measurement, we obtained the turn-on voltage at about 6 V and observed an anomalous behavior at 3∼4 V. And we used other buffer layer of PEDT(3,4-pyrazino-3',4'-ethylenedithio-2,2',5,5'-tetrathiafulvalenium) with ITO/PEDT/TPD/Alq$_3$Al structure. We observed a surface morphology by AFM(Atomic Force Microscopy), UV/visible absorption spectrum, and PL(Photoluminescence) spectrum. We obtained the UV/visible absorption peak at 358nm in TPD and at 359nm in Alq$_3$, and the PL peaks at 410nm in TPD and at 510nm in Alq$_3$. We also studied EL spectrum in the cell structure of ITO/(TPD+PEI)/Alq$_3$/Al.