• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.39 no.3
• /
• pp.1-10
• /
• 2002

Because of the reduced number of displayable gray levels resulting from inverse gamma correction, images on a plasma display panel (PDP) exhibit undesirable false contours in dark areas. An error diffusion method has been applied to remedy this problem. However, it is computationally expensive and requires large memory resources. This paper proposes a computationally efficient dithering based technique to improve the gray level reproduction capability in dark areas. In the proposed method, multiple dithering masks ate utilized in turn to improve the gray level reproduction in dark areas. Also, in order to reduce undesirable regular patterns generated by the dithering method, positions of threshold values within a given dithering mask are changed. Compared to the error diffusion method, the proposed method requires much less computations and memory resources with a comparable gray level reproduction capability.

• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.721-727
• /
• 2002

In order to overcome trade-off among compositions, process and properties of the glasses with high PbO-base composition for PDP Rib, we studied glass crystallization and crystallization kinetics by Differential Thermal Analysis(DTA). Glass powder was obtained through melting/cooling/grinding, with 3 wt%TiO2 addition for the crystal nucleation and growth in $62PbO-19B_2O_3-10SiO_2-9(Al_2O_3-K_2O-BaO-ZnO)$(in wt%) composition glass. This powder was heat-treated for 1 to 10 h at $445^{\circ}C$ for nucleation. DTA measurements were performed to obtain the crystallization peak with $5∼25^{\circ}C/min$ heating rates. DTA crystallization peak temperature increased with increasing the heating rate and decreased with increasing the heating time. Because the Avrami parameter (n) was approximately 1, the surface crystallization occurred. The maximum nucleation time was 2 h.

• Korean Journal of Materials Research
• /
• v.14 no.9
• /
• pp.670-675
• /
• 2004

Glasses in the $Bi_{2}O_3-SiO_2-ZnO$ glasses system were examined as a potential replacement for lead-oxide glass frits with low firing temperature ($500\sim600^{\circ}C$) for the dielectric layer of a plasma display panel (PDP). The glasses were evaluated for glass transition temperature($T_{g}$) and thermal expansion coefficient(${\alpha}$). After forming transparent thick films by a screen-printing method, it was evaluated for the optical properties. The transmittance of thick films fired at $500-600^{\circ}C$ showed above $80\%$, which was not dependent on the firing temperature. As a result, many pores were observed at samples fired at low temperature, while the number of pores from samples prepared at high temperature decreased and the pores size increased.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.197-197
• /
• 2003

현재 PDP(Plasma Display Panel) 투명유전체층은 PbO 계열을 사용하고 있으나 제조공정 시 다량의 중금속 페기물이 방출됨에 따라 환경오염을 야기시킴으로 무연조성이며 저온소성이 가능한 저융점유리인 인산염계 유리에 대한 열적, 화학적, 광학적 특성에 대해 체계적인 연구가 진행되었다. 광학적 특성을 위 한 승온속도, 소성온도, 유지시간의 변화 그리고, 프릿 입도에 따른 광 투광성, 기포의 형성, 그리고 기포의 분포특성을 연구하였다. 열적특성은 DTA와 TMA를 이용하여 유리전이점(Tg) 및 선팽창계수(CTE)와 Littleton softning point (Ts)가 측정되었다. 광학적특성은 스크린프린팅법으로 후막 제조 후 소성하여 UV-visible spectrometer을 이용하여 300~800nm영역에서 투광성을 측정하였으며, FEG-SEM, AFM을 이용해 표면을 관찰하였다. 결과로써, Tg는 440-46$0^{\circ}C$ 와 CTE는 7~8.5$\times$$10^{-6}$K값을 보였고 높은 화학적 내구성과 60-80%의 광투과율을 나타내었다. 프릿의 미세화, 숭온속도의 감소는 기포의 생성을 줄이는데 효과를 보였으며, 그 결과 양호한 광투과율을 얻을 수 있었다. 이러한 결과에 따르면, P$_2$O$_{5}$-ZnO-RO 조성은 PDP용 투명유전체 조성으로써 기존의 PbO계열을 대체할만한 새로운 조성으로 고려된다.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.551-555
• /
• 2004

The two-transformer full bridge (TTFB) PWM converter has two transformers which act as the output inductor as well as the main transformer, i.e. as the forward and the flyback transformer. Although the doubled leakage inductor of the TTFB makes it easier to achieve the zero-voltage switching (ZVS) of the lagging leg switch along the wide load range, it instigates a serious voltage ringing in the secondary rectifier diodes, which would require the dissipative snubber circuit, cause the serious power dissipation, and increase the voltage stress across those diodes. To overcome these problems, a, new lossless diode-clamp rectifier (LDCR) is employed as the output rectifier, which helps the voltage across rectifier diodes to be clamped on a half the output voltage $(V_o/2)$ or the output voltage $(V_o)$. Therefore, no dissipative snubber for rectifier diodes is needed and a high efficiency as well as low noise output voltage can be realized. The operations, analysis and design consideration of proposed converter are presented in this paper. To verify the validity of the proposed converter, experimental results from a 425W, 385-170Vdc prototype for the plasma display panel (PDP) sustaining power module (PSPM) are presented.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.4
• /
• pp.219-224
• /
• 2006

Silver paste with low sintered temperature has been developed in order to apply electronic parts, such as bus electrode, address electrode in PDP (Plasma Display Panel) with large screen area. In this study, nano-sized silver particles with 10-30 nm were synthesized from silver nitrate ($AgNO_3$) solution by chemical reduction method and silver paste with low sintered temperature was prepared by mixing silver nanoparticles, conventional silver powder with the particle size 1.6 um and Pb-free frit. Conductive thick film from silver paste was fabricated by screen printing on alumina substrate. After firing at $540^{\circ}C$, the cross section and surface morphology of the thick films were analyzed by FE-SEM. Also, the sheet resistivity of the fired thick films was measured using the four-point technique.

• Journal of the Korean Ceramic Society
• /
• v.48 no.6
• /
• pp.565-570
• /
• 2011

The $Eu^{3+}$ doped $Y(P_x,V_{1-x})O_4$ (0 ${\leq}$ x ${\leq}$ 1) phosphors were synthesized by solid-state and impregnation method and investigated as potential red-emitting phosphors for a plasma display panel(PDP). The optimal substitution proportion of P for V was determined to be 60 mol%, for $Y(P_x,V_{1-x})O_4$ doped with 8 mol% $Eu^{3+}$. The VUV PL spectra and SEM for the synthesized phosphors were measured and compared against those of a commercial red-emission phosphor. The $Y(P_x,V_{1-x})O_4$:$Eu^{3+}$ phosphors exhibited strong red at around 592, 618 and 698 nm. The emission intensity and particle size of the phosphors were controlled by preparation conditions.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.390-392
• /
• 2006

단일 서스테인 구동회로서 패널을 수평으로 이등 분할하고 직렬 연결하여 구동회로의 전류 스트레스를 저감하는 새로운 단일 에너지 회수 서스테인 구동회로를 제안한다. 기존의 단일 서스테인 구동회로는 +Vs 및 -Vs의 양극성 전원을 사용함에 따라 기존 구동회로에 비해 전류 스트레스는 그대로이면서 스위치 전압 스트레스가 두 배가 되어 회로 손실 및 발열이 높은 단점을 가지고 있다. 이를 개선하기 위해 제안하는 패널 분할 직렬 연결 단일 에너지 회수 서스테인 구동회로는 패널을 수평으로 이등 분할하고 하프 브리지 인버터를 각각 연결하여 구동 회로의 가스 방전 전류 및 패널 캐패시터의 변위 전류를 기존의 절반으로 줄여 스위치들의 전류 스트레스를 저감하게 된다. 또한 에너지 회수 회로는 능동소자로서 단 하나의 스위치와 단하나의 다이오드만을 사용하므로 그 구조가 단순하여 원가를 절감할 수 한다.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.547-550
• /
• 1999

Optical and electrical properties of MgO-CaO films as a protective layer for AC plasma display panel were studied. When the [(CaO/(MgO+CaO)] ratio of evaporation starting materials was optimum composition, 0.1, firing voltage and memory margin of the film were 176V and 0.5, respectively. When [CaO/(CaO+MgO)] was 0, 0.1 and 0.2, memory margin was 0.39, 0.5 and 0.41, respectively, and surface roughness of films was $27.7\AA$, $21.1\AA$ and $40.3\AA$, respectively. It was thought that memory margin had a reverse-relation with surface roughness. The density of film was calculated by measuring the refractive index of film. The density of MgO film was 3.21g/㎤ and the density of film, when [CaO/(CaO+MgO)] was 0.1, was 3.632g/㎤. The mixture of MgO-CaO films showed a good transmittance property in the visual range.

• Polymer(Korea)
• /
• v.34 no.3
• /
• pp.226-236
• /
• 2010

UV irradiated acrylic pressure sensitive adhesives(PSAs) are prepared to be used for thermal pad in plasma display panel(PDP). The effect of the chemical structure of side-chain in comonomer and of crosslinking agent on wet-out property of acrylic PSAs in wide temperature range were investigated. The correlationship between viscoelastic behavior and adhesion properties, such as tack and peel strength, was also studied. The experimental results supported that wet-out and adhesion properties of acrylic PSAs were enhanced inversely proportional to side-chain length of comonomer in wide temperature range. The peel energy clearly increased in acrylic PSAs prepared by using di(ethylene glycol) dimethylacrylate (DEGDMA) for crosslinking agent. The results might be due to the difference in the glass transition temperature and viscoelastic behavior of acrylic PSAs.