• Bulletin of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.1967-1971
• /
• 2012

A hexavalent chromium (Cr (VI)) is one of the hazardous substances regulated by the RoHS. The determination of Cr (VI) in various polymers and printed circuit board (PCB) has been very important. In this study, the three different analytical methods were investigated for the determination of a hexavalent chromium in Acrylonitrile Butadiene Styrene copolymer (ABS) and PCB. The results by three analytical methods were obtained and compared. An analytical method by UV-Visible spectrometer has been generally used for the determination of Cr (VI) in a sample, but a hexavalent chromium should complex with diphenylcarbazide for the detection in the method. The complexation did make an adverse effect on the quantitative analysis of Cr (VI) in ABS. The analytical method using diphenylcarbazide was also not applicable to printed circuit board (PCB) because PCB contained lots of irons. The irons interfered with the analysis of hexavalent chromium because those also could complex with diphenylcarbazide. In this study, hexavalent chromiums in PCB have been separated by ion chromatography (IC), then directly and selectively detected by inductively coupled plasma atomic emission spectrometry (ICP-AES). The quantity of Cr (VI) in PCB was 0.1 mg/kg.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.11
• /
• pp.2038-2042
• /
• 2010

In this paper, we confirmed the thermal & optical properties for improving the heat transfer coefficient by changing the via hole size and in FR4 PCB with the same area. Osram 1W power LED Package (Golden Dragon) was used and the K-factor which is relative constant between LED junction temperature and forward bias was measured with power source meter(KEITHLEY 2430) to measure the thermal resistance from PCB configuration. As results, thermal resistance in metal PCB came out to the lowest as $26 [^{\circ}C/W]$ and thermal resistance in FR4 PCB without via-holes emerged as the highest as $69 [^{\circ}C/W]$. However thermal resistance of FR4 PCB could have decreased until $32[^{\circ}C/W]$ in 0.6 mm by using the via hole. Also, the luminous flux could have improved, too.

• Journal of Aerospace System Engineering
• /
• v.14 no.3
• /
• pp.51-59
• /
• 2020

In the case of cubesat, a PCB-based deployable solar panel advantageous in terms of weight reduction and electrical circuit design is widely used considering the limited weight and volume of satellites. However, because of the low thermal conductivity of PCB, there is a limit relative to heat dissipation. In this paper, the thermal gap pad is applied to the contact between the PCB-based solar panel and the aluminum stiffener mounted on the outside of the panel. Thus, the heat transfer from the solar cell to the rear side of the panel is facilitated. It maximizes the heat dissipation performance while maintaining the merits of PCB panel, and thus, it is possible to improve the power generation efficiency from reducing the temperature of the solar cell. The effectiveness of the thermal design of the 6U cubesat's deployable solar panel using the thermal gap pad has been verified through on-orbit thermal analysis based on the results, compared with the conventional PCB-based solar panel.

• Journal of Advanced Navigation Technology
• /
• v.23 no.5
• /
• pp.430-436
• /
• 2019

It is needed to develop an antenna with features of subminiature, light weight and multi-band operation for the variaty services in maritime and industrial fields. The PCB pattern antenna is one of the appropreiate antennas solving these requirements. In this research, the design and fabrication of the PCB pattern antenna operating on the single band of 920 MHz are investigated. The final goal is that the development of the dual band PCB pattern antenna operating on 260 MHz and 920 MHz, which is based on the proposed antenna. It is evident that the performance in the frequencies of 902 MHz, 915 MHz and 928 MHz among of 920 MHz ISM band is better than that in other frequencies. It is also confirmed that the differences of the voltage standing wave ratio, return loss, gain and efficiency between three frequencies are less than 5%. It is expected that the development of communication link of 5-10 km is possible when the induced results are applied into the low power wide area (LPWA) network desinged by the rule of -30 dB sensitivity.

• Animal Bioscience
• /
• v.34 no.2
• /
• pp.233-242
• /
• 2021

Objective: The aim of this study was to determine the effect of pineapple cannery by-product (PCB) level on the growth performance and carcass characteristics of finishing Hanwoo steers. Methods: The feeding stage was divided into early and late finishing stages. A total of 60 castrated Hanwoo steers (13.9±0.8 months old, 418.8±36.5 kg initial body weight [BW]) were blocked by initial BW and then randomly allotted into 12 pens (five head/pen). The pens were randomly assigned to control (CONT), low PCB (LPCB), or high PCB (HPCB) treatments. These diets contained 0%, 1.5%, or 3.0% of PCB (on a dry matter [DM] basis; as-fed basis was 0%, 10.6%, or 21.2%), respectively. Results: For the early finishing stage, body weight gain (BWG) and average daily gain (ADG) of the CONT and LPCB feeding groups were greater (p<0.05) than those of the HPCB feeding group. In addition, there were linear and quadratic effects on BWG and ADG with increasing dietary PCB level (p<0.05). The gain to feed (G:F) ratio tends to quadratically decrease with an increasing PCB level in the early finishing stage (p = 0.076). Growth performances of late finishing stage were not affected by PCB level. The marbling score of the LPCB feeding group was similar to that of the CONT feeding group. However, there was a linear decrease (p< 0.05) in marbling score and quality grade among treatments as PCB was increased in the diet. In the longissimus muscle free amino acid profile, histidine composition increased linearly (p<0.05) with an increasing level of PCB. Conclusion: The level of PCB 1.5% DM in diet can be used for finishing steers without any adverse effects on growth and carcass performances. However, there were some negative effects on growth and carcass performance in the HPCB feeding group.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.2
• /
• pp.170-176
• /
• 2005

This study was conducted to investigate the level of PCBs and distribution of PCB congeners in the ambient air of Korea and Japan. The source of PCBs were also studied by a statistical method. The TEQ concentration of PCB in the ambient air of Korea and Japan were between 0.003 and $1.01\;pgTEQ/m^3$(mean value : $0.22\;pgTEQ/m^3$) and between 0.002 and $0.014\;pgTEQ/m^3$ (mean value: $0.007\;pgTEQ/m^3$), respectively. The ambient air of industrial area of Korea showed a fluctuation in PCB concentration than other sampling area. The isomer distribution patterns in the ambient air was more or less similar in all sampling places. In addition, highly chlorinated homologues ($7{\sim}10CB$) were detected in the only Korea industrial area. This observation suggests that there is a possibility of specific source of PCBs in the industrial area. The source identification of PCB in ambient air was performed using multivariate statistical analysis(principal component analysis). As a result, it is estimated that the Korean ambient air was more influenced by combustion process than the ambient air of Japan and also the effect of PCB commercial products was relatively a small.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.12 no.1
• /
• pp.24-31
• /
• 2007

Global fates of polychlorinated biphenyl(PCB) were investigated with a fugacity based multimedia transport and fate model, Globe-POP(persistent organic pollutant). The accumulation of PCB was directly affected by the emission patterns of PCB into the atmosphere and surface areas of environmental compartments. Partition coefficients and reaction rates also influenced on the accumulation patterns of PCB. The emission patterns of PCB in 10 climate zones were consistent for the past 70 years, while the contribution of PCB in high-latitude zones to the globe has increased by cold condensation. Considering the amounts of emission and accumulation of PCB, the North temperature zone is regarded as an important source and sink of PCB. Meanwhile, in spite of no significant sources, POPs accumulate in Antarctic environments mainly due to extremely low temperature. Finally we suggested that a global water balance accounting for snow/ice should be incorporated into multimedia environmental models for high-latitude zones and polar regions with the seasonal snow pack and/or permanent ice caps. The modified model will be useful to evaluate the influence of climate change on the fate of POPs.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1995.04a
• /
• pp.203-210
• /
• 1995

A construction method for continuous prestressed Composite Bridges(PCB's) is developed and successfully applied to the design of two-span continuous PCB's of five different span lengths. The construction of continuous PCB's goes through 17 different loading conditions. for each loading condition, the allowable stress design method is used to determine section properties. The analytical results of two-span continuous PCB's arc compared with those of simple PCB's. The comparison shows that the use of the proposed method can reduce 10-15 percents of the concrete section area and approximate 28 percents of the steel section area, as well as 5-8 percents of the girder height. The study indicates that the use of the proposed PCB's method can significantly reduce construction and maintenance costs of bridges.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.2 s.105
• /
• pp.148-151
• /
• 2006

The DC power-bus' resonance is frequently attributed to EMI sources in the PCBs. Subsequently, it will ruin the digital signal integrity within one system or between adjacent systems in the form of conducted or radiated emission. Hence, since it is of importance to examine the PCB's emission, this paper sheds a light on the radiated emission from the power-bus with regards to its resonance modes. A full-wave analysis method is used to calculate the impedance and radiated electric fields and is validated by physics and an EM analysis tool.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.3 s.180
• /
• pp.102-109
• /
• 2006

Several methods for PCB pattern inspection have been tried to detect fine detects in pad contours, but their low detection accuracy results from pattern variations originating from etching, printing and handling processes. The adaptive inspection algorithm has been newly proposed to extract minute defects based on movable segments. With gerber master images of PCB, vertex extractions of a pad boundary are made and then a lot of segments are constructed in master data. The pad boundary is composed of segment units. The proposed method moves these segments to optimal directions of a pad boundary and so adaptively matches segments to pad contours of inspected images, irrespectively of various pattern variations. It makes a fast, accurate and reliable inspection of PCB patterns. Its performances are also evaluated with several images.