• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.3
• /
• pp.164-167
• /
• 2003

In this study, we developed the mold for the plastic cavity filter which is a kind of a wireless communication device. Since the cavity filter is made of aluminium, the cost of fabrication is high and the production rate is low. But we can produce plastic cavity filter part by injection molding process with the mold which was designed by our team. The dimension and surface quality of plastic cavity filter was investigated by varying the molding method (conventional and MmSH process) and two different types of resin(PC/ABS and ABS). In case of ABS part, the shrinkage of the inner partition walls was decreased when we adopted MmSH method. The weight of both ABS and PC/ABS parts increased and the surface roughness decreased with MmSH process.

• Journal of the Korean Ceramic Society
• /
• v.48 no.6
• /
• pp.504-509
• /
• 2011

In this study, the effect of superplasticizers on the dispersibility and hydration properties of cement with silica fume were investigated. Superplasticizers are used Naphthalene type, Ligno-sulfate type and polycarboxylate type. Compared with plastic viscosity of cement paste without superplasticizers(Plain), plastic viscosity of cement paste with superplasticizers are reduced and yield stress of cement pastes with each superplasticizer is increased rather than Plain. And then, plastic viscosity of cement paste with Naphthalene type superplasticizer was the least of all types. Compared with other two types, setting and hydration of cement paste with Polycarboxylate type(PC) superplasticizer is very fast. At compressive strength after 3-day, PC is higher than other two types, But, compressive strength of after 7-day and 28-day, PC is smaller than other two types.

• Journal of the Korean Ceramic Society
• /
• v.45 no.6
• /
• pp.336-344
• /
• 2008

Rheological properties of cement pastes containing blast furnace slag (BFS: 3,900, $7,910\;cm^2/g$) or fly ash powder (FA: 4,120, $8,100\;cm^2/g$) according to the ratio of water/binder (W/B) and the dosage of polycarboxylate type superplasticizer (PC) were investigated by a mini slump and a coaxial cylinder viscometer. In this experiment, the ratio of replacing OPC with BFS or FA was 30 wt%, the W/B was from 30 to 70 wt%. As a result, the fluidity of cement paste containing BFS or FA was improved with increasing W/B and the dosage of PC. BFS or FA replaced cement paste with W/B 70% and PC 0.3% showed the highest fluidity. The segregation range of cement paste was occurred below $10\;d/cm^2$ of the yield stress and below 50 cPs of the plastic viscosity by the coaxial cylinder viscometer. And also it was formed that the plastic viscosity and the yield stress of FA replaced cement paste were higher than them of BFS replaced cement paste.

• Textile Coloration and Finishing
• /
• v.5 no.1
• /
• pp.19-25
• /
• 1993

Plastic optical fibers(POFs) composed of poly(methylmethacrylate) (PMMA), polystyrene (PS), or polycarbonate(PC) as a core materials, and of fluorinated polymer or PMMA as a cladding were fabricated and their properties were investigated in this study. The attenuation loss of PMAA core POF was about 1,700 dB/Km at 660 nm, the loss of PS core POF was 1,800 dB/Km at 560 nm, and the loss of PC core POF was 2,200 dB/Km at 780 nm. These attenuation losses of POFs prepared ill this study were higher than those of commerically available POFs. Compared to PMMA and PS core POFs, PC core POF has excellent characteristics, including high thermal stability, high flexibility, and high impact strength.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.11 no.1
• /
• pp.47-52
• /
• 2005

The wasted plastic PC/ABS retainer, polyurethane foam (PUF) and vinyl (PVC) skin. In order to investigate the recycling process, the multi-layered instrument panel Each of materials separated was shredded and crushed to create many small particles respectively. The separation of the foam and skin and retainer of zigzagged air blower. Pilot tests performed at the equipment yielded 98.8% by weight of the available PVC and 99.3% by weight of the available PC/ABS respectively. Secondly, the thermal stabilizer and the compatabilizer have been used to improve the physical propertied of recycled materials.. The properties of recycled PVC materials resulted in about 50% compared to that of virgin materials after treatment by Pb-St thermal stabilizer. In addition, the properties of recycled PC/ABS materials was also obtained about 80% compared to that of virgn materials after treatment by PMMA compatabilizer.

• Elastomers and Composites
• /
• v.47 no.4
• /
• pp.336-340
• /
• 2012

Residual stress in the injection molded part is originated from thermal shrinkage and shear stress during injection molding process. There are many measurement methods of residual stress in the plastic part. Residual stress in opaque products can be measured by chemical cracking test. This method enables the solvent and specimen to react and to cause cracks. Cracks developed according to the level of residual stress. Thus the stresses in plastic part can be quantitatively measured by counting the number of cracks or measuring the size of cracks. Relationship between stress and number of cracks in a plastic specimen has been investigated in this study. Bergen jig was used to give a strain in the specimens those were molded using PC/PBT and PC/ABS. Solvent for the chemical cracking test was prepared using tetrahydrofuran and methyl alcol with the ratio of 1 to 3. Stresses in the specimen can be calculated by strains those were imposed by Bergen jig. Cracks were developed for stress higher than certain level. The number of cracks increased by second order function for stress.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2549-2552
• /
• 2003

The greenhouse control system is designed by personal computer. This system should observe and control the growth conditions for crops in both plastic film and glass greenhouses. In this contribution puts emphasis on graphical user interface for greenhouse control system by personal computer under the aim of creating safer, more effective and more economical services. This system is developed for the requirements of the intelligent greenhouse control system and gives a lot of convenience for farmer who is not familiar with pc technique. The GUI and control system are programmed by Visual C++ and Visual Basic.

• Journal of the Korean Society of Safety
• /
• v.29 no.5
• /
• pp.15-21
• /
• 2014

The aim of this work is conduct the study on light weight and structural performance improvement of the composite wind power blade. GFRP (Glass Fiber Reinforced Plastic) pre-empted by CFRP(Carbon Fiber Reinforced Plastic), the major material of wind power blade, was identified the superiority of mechanical performance through the tensile and fatigue test. SENT(Single Edge Notched Tension) specimen fracture test was conducted on the specimen that laminated together 2 ply CFRP with 4 ply GFRP through DIC(Digital Image Correlation) analysis. The SENT specimen thickness and $a_0/W$ ratio is 1.45 mm and 0.2, respectively. The fracture test accomplished with displacement control with 0.1 mm/min at the room temperature. The experimental apparatus used for the fracture test consisted of a 50kN universal dynamic tester and CCD camera connected to a personal computer (PC), which was used to record images of the specimen surface. Following data acquisition, the images and load-displacements were transferred to the PC, on which the DIC software was implement. The experiment and DIC analysis results show that CFRP/GFRP laminated composite exhibits improvement of the strength, compared with that of the existing blade material. This study shows the result that the strength of CFRP rotor blade of wind turbine satisfies through the experimental and DIC method.

• Steel and Composite Structures
• /
• v.24 no.3
• /
• pp.287-296
• /
• 2017

The buckling capacity of a radially retractable hybrid grid shell in the closed position was investigated in this paper. The geometrically non-linear elastic buckling and elasto-plastic buckling analyses of the hybrid structure were carried out. A parametric study was done to investigate the effects rise-to-span ratio, beam section, area and pre-stress of cables, on the failure load. Also, the influence of the shape and scale of imperfections on the elasto-plastic buckling loads was discussed. The results show that the critical buckling load is reduced by taking account of material non-linearity. Furthermore, increasing the rise-to-span ratio or the cross-section area of steel beams notably improves the stability of the structure. However, the cross section area and pre-stress of cables pose negligible effect on the structural stability. It can also be found that the hybrid structure is highly sensitive to geometric imperfection which will considerably reduce the failure load. The proper shape and scale of the imperfection are also important.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.2
• /
• pp.154-163
• /
• 2013

Adhesive bonding and plastic welding have been widely used to join two plastic materials together. The goal of this paper is to determine a proper joining technology of a pair of flat panel (FP) photobioreactor (PBR) case. The material of the FP PBR case is polycarbonate (PC) plate. Two types of adhesion, including acryl adhesive and two-part epoxy adhesive, as well as two types of plastic welding technology, including ultrasonic welding and thermal welding, are employed for joining of PC plates. In order to influence of the adhesion and welding conditions on the joining characteristics of the PC plates in operational conditions of the FP PBR case, the morphology in the vicinity of the joined region as well as the water and pressure resistance characteristic are investigated. In addition, the variation of the bonding strength of the joined region and deformation behaviors in the vicinity of the joined region according to the adhesion and welding conditions is examined via the lap-shear test. From the results of basic experiments, proper joining technologies are chosen. Using the chosen joining technologies, the FP PBR case are fabricated to perform full-scale durability experiment. The results of the full-scale durability experiment have been shown that the chosen joining technologies can be applicable to fabricate the FP PBR case.