• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.60-68
• /
• 2007

A technique is presented to extract differential second harmonic output from common source nodes of a cross-coupled P-& N-FET oscillator. Provided the impedances at the common source nodes are optimized and the fundamental swing at the VCO core stays in a proper mode, it is found that the amplitude and phase errors can be kept within $0{\sim}1.6dB$ and $+2.2^{\circ}{\sim}-5.6^{\circ}$, respectively, over all process/temperature/voltage corners. Moreover, an impedance-tuning circuit is proposed to compensate any unexpectedly high errors on the differential signal output. A Prototype 5-GHz VCO with a 2.5-Hz LC resonator is implemented in $0.18-{\mu}m$ CMOS. The error signal between the differential outputs has been measured to be as low as -70 dBm with the aid of the tuning circuit. It implies the push-push outputs are satisfactorily differential with the amplitude and phase errors well less than 0.34 dB and $1^{\circ}$, respectively.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.769-772
• /
• 2005

This paper describes a low-voltage and low-power channel selection analog front end with continuous-time low pass filters and highly linear programmable-gain amplifier(PGA). The filters were realized as balanced Gm-C biquadratic filters to achieve a low current consumption. High linearity and a constant wide bandwidth are achieved by using a new transconductance(Gm) cell. The PGA has a voltage gain varying from 0 to 65dB, while maintaining a constant bandwidth. A filter tuning circuit that requires an accurate time base but no external components is presented. With a 1-Vrms differential input and output, the filter achieves -85dB THD and a 78dB signal-to-noise ratio. Both the filter and PGA were implemented in a 0.18um 1P6M n-well CMOS process. They consume 3.2mW from a 1.8V power supply and occupy an area of $0.19mm^2$.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.11a
• /
• pp.112-119
• /
• 2001

Parameter tuning methods by Ziegler-Nickels for control systems are generally classified into Z-N(1) and Z-N(2). The purpose of this paper is to describe what relations exist between methods of Z-N(1) and Z-N(2), or how Z-N(1) method can be originated from Z-N(2) method by analyzing one loop control system of P or PI controller and time delay process. The formulas of Z-N(1) consist of process parameters, L(time delay), $K_m$(gain) and $T_m$(time constant), but Z-N(2) method is based only on the ultimate gain $K_u$ and the ultimate period $T_u$ acquired normally by practical trial without any parameters of Z-N(1). In this paper, for the first step to seek mutual relations, the simple formulas of Z-N(2) are transformed into the formulas composed of the same parameters as Z-N(1) which is derived from the analysis of frequency characteristics. Then, the approximation of the actual ultimate frequency is proposed as important premise in the translation between Z-N(1) and (2). Such equalization and approximation brings a simple approximated formula which can explain how Z-N(1) is originated from the Z-N(2) in the form of formula. And a model system is adopted to compare the approximated formula to Z-N(1) and Z-N(2) methods, the results of which show the effectiveness of the proposals.

• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.149-153
• /
• 1997

We demonstrate the operating characteristics(center wavelength, bandwidth, TE/TM polarization, tuning range) of grating-assisted co-directional coupler(GACC) filter fabricated with InGaAsP compound semiconductor. A design of waveguide structure has been focused on the narrow bandwidth characteristics of the filter. Reactive ion etching technique was employed for the uniform waveguide formation. The bandwidths(FWHM) and center wavelengths of the fabricated GACC filter were measured by 1.5 nm and 1530.6 nm for TE polarization and 1.3 nm and 1494.0 nm for TM polarization. This is the one of the narrowest bandwidth at 1530 nm region ever reported. The center wavelength shifted form 1530 nm to 1538 nm when the current of 100 mA was injected at 4.5 mm-long device. Good agreement between the designed and measured operating characteristics for some waveguide structures is demonstrated.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.178-184
• /
• 2010

The aim of this work is the fabrication of polyelectrolyte microcapsules composed of biocompatible polymers such as chitosan, heparin and alginate, to encapsulate the fluorescein isothiocyanate(FITC)-albumin, and to investigate the protein release behavior therefrom. Polyelectrolyte capsules with 4-layer structures could be prepared with biocompatible materials by oppositely charged adsorption using melamin-foramide as a template. Transmission electron microscope(TEM), scanning electron microscope(SEM) and optical microscope confirmed hollow capsule structures. Protein release before and after encapsulation was monitored with a UV-Vis spectrometer. Microcapsules have different behaviors depending on the kind of polyelectrolyte polymers, chitosan-heparin capsules or chitosan-alginate capsules. In conclusion, the polyelectrolyte multilayer shells can be switched between an open and closed state by means of tuning the pH value.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.2
• /
• pp.162-168
• /
• 2014

Use of nonlinear loads, such as power converters, fluorescent lamps and adjustable speed motor drives, is expected to grow rapidly. All of these loads inject harmonic currents. This paper presents the active filtering of the harmonic distortion generated by the compact fluorescent lamps (CFL). The Instantaneous active and reactive power theory (the p-q Theory) is used to design the control of parallel active filter. The control scheme has been verified using Matlab/Simulink with SimPower Systems through a set of simulation tests under different load conditions. Also, the tuning of the active power filter is performed to improve the quality of the electrical power supply.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.2
• /
• pp.201-208
• /
• 1999

This paper presents the degradation of the system performance according to the vmiation of the rotor time constant. The algorithm for the on-line estimation of rotor time constant is proposed. which is applied to the consistent relationship between the tangent torque angle of the synchronous reference frame and that of stationary reference f frame. For the purpose of the validity of proposed algorithm. the computer simulation and the experiments have been p performed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.4
• /
• pp.665-670
• /
• 2009

The second paper, Part 2, describes the field testing of IEEE type PSS2A EX2000 excitation in the Dangjin 612 MVA T/P #4. The final PSS gain, $K_s$, was determined by inputting 2%-step signals into AVR at a loading of 500MW and increasing $K_s$, from 0 to 15 in increments of 3. After the field testing, the measured data was also analyzed by Discrete Fourier Transformation(DFT) analysis, and the model parameters of generation system were verified by replicating the measured data with the transient stability program.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.4
• /
• pp.292-297
• /
• 2016

The first-order plus dead time(FOPDT) and second-order plus dead time(SOPDT), which describes a linear monotonic process quite well in most chemical and industrial processes and is often sufficient for PID and IMC controller tuning. This paper presents an application of heuristic harmony search(HS) optimization algorithm to the identification of linear continuous time-delay systems from step response. This recently developed HS algorithm is conceptualized using the musical process of searching for a perfect state of harmony. It uses a stochastic random search instead of a gradient search so that derivative information is unnecessary. The effectiveness of the proposed identification method has been demonstrated through a number of simulation examples.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.156-160
• /
• 1997

In this paper, the control scheme is proposed that PI controller parameter used for TAH speed control is adapted by fuzzy logic method using only the motor current waveform. By scheduling PI parameters, minimization of the vibration and the energy consumption and overcoming AoP loads becomes possible. In in vitro tests experimental results show our approach is a good scheme that is adapted to changing afterloads well.