• Fire Science and Engineering
• /
• v.24 no.6
• /
• pp.28-33
• /
• 2010

The present study develops a numerical model based on the computational fluid dynamics technique to analyse the thermal flow characteristics of large scale fire calorimeter and examine the characteristics of primary parameters affecting on the uncertainty of heat release rate measurement. ANSYS CFX version 12.1 which is a commercial CFD package is used to solve the governing equations of the thermal flow field and the eddy dissipation combustion model and P-1 radiation model are applied to simulate the fire driven flow. The numerical results shows that the horizontal duct system with $90^{\circ}$ bend duct was shown relatively high deviated asymmetric flow profiles at the sampling location and the deviation of the velocity field was higher than that of the temperature and species quantities. The present study shows that the computational model can be applicable to optimize the design process and operating condition of the large scale fire calorimeter based on the understanding of the detail flow field.

• Computational Structural Engineering
• /
• v.5 no.1
• /
• pp.75-82
• /
• 1992

In the h-version of F.E.M., all piecewisely smooth curved boundaries can be approximated by a sufficient number of straight-sided elements. However, in the p-version the size of the element is usually large and hence the probability of distortions is more. An attempt has been made to generate a curved boundary by using a transfinite interpolation technique to avoid the discretization errors. In the following sections, it will be shown how to construct transfinite interpolants both in h-version and in p-version over polygonal and nonpolygonal regions. Three numerical tests are shown to validate the applicability and superior capability of transfinite interpolation technique.

• The Journal of Engineering Geology
• /
• v.13 no.1
• /
• pp.17-27
• /
• 2003

In this study, a phenomenon of saltwater intrusion was monitored under various conditions regarding recharge and pumping rate using time domain reflectometry for a laboratory scale unconfined aquifer to verify the basic theory behind seawater intrusion and to investigate movement of salt-freshwater interface in accordance with the ratio of pumping and recharge rate. Results showed that a thick mixing zone was formed at the boundary instead of a sharp salt-freshwater interface that was assumed by Ghyben and Herzberg who derived an equation relating the water table depth $(H_f)$ to the depth to the interface $(H_s)$. Therefore our experimental results did not agree with the calculated values obtained from the Ghyben and Herzberg equation. Position of interface which was adopted as 0.5 g/L isochlor moved rapidly as the Pumping rate $(Q_p)$ increased for a given recharge rate $(Q_r)$. In addition, interface movement was found to be about 7 times the ratio of $Q_p/Q_r$ in our experimental condition. This indicates that Pumping rate becomes an important factor controlling the seawater intrusion in coastal aquifer.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.1
• /
• pp.55-60
• /
• 2011

In the present work, isogeometric analysis in linear elasticity problem is conducted using the basis functions from NURBS. The objectives of isogeometric analysis introduced is to integrate both geometric modeling(CAD) and computational analysis(CAE), and this can be accomplished from direct usage of geometric modeling by NURBS as the computational mesh. The merit of the isogeometry analysis is that NURBS surface are able to represent exact geometry from the control points and knot vectors, and also subsequent refinement is relatively simple relatively. In order to verify the computer codes developed in this study, it has been applied to two structural models of which geometry are simple ; 1) circular cylinder subjected to the constant internal pressure loading, 2) square plate with circular hole at center subjected to uniform tension. The exact solutions of these two models are available. Convergence of the approximate solutions by the present code for the isogeometry analysis are investigated by mesh refinement with inserting knots (h-refinement) and by mesh refinement with order elevation of the basis functions (p-refinement).

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.05a
• /
• pp.227-232
• /
• 2005

Least squares (${\ell}^2-norm$) solutions of seismic inversion tend to be very sensitive to data points with large errors. The ${\ell}^p-norm$ minimization for $1{\le}p<2$ gives more robust solutions, but usually with higher computational cost. Iteratively reweighted least squares (IRLS) gives efficient approximate solutions of these ${\ell}^p-norm$ problems. I propose a simple way to implement the IRLS method for a hybrid ${\ell}^1/{\ell}^2$ minimization problem that behaves as ${\ell}^2$ fit for small residual and ${\ell}^1$ fit for large residuals. Synthetic and a field-data examples demonstrates the improvement of the hybrid method over least squares when there are outliers in the data.

• Journal of ILASS-Korea
• /
• v.20 no.1
• /
• pp.53-58
• /
• 2015

In this study, we prepare the Ag nanofluids synthesized by the chemical reduction method and measure the extinction coefficient of those nanofluids at a wavelength of 632.8 nm. The Ag nanofluids are synthesized by the chemical reduction method using silver nitrate ($AgNO_3$) and sodium borohydride ($NaBH_4$) in water and ethylene glycol (EG). For stable dispersion of Ag particles in the base liquids, polyvinyl pyrrolidone (PVP) is added as a surfactant. The extinction coefficient of manufactured Ag nanofluids is measured by an in-house developed measurement system at the wavelength of 632.8 nm. The results show that the extinction coefficient of water-based and EG-based Ag nanofluids is linearly increased with respect to the particle loadings. Moreover, it is shown that the extinction coefficient of EG-based Ag nanofludis is higher than that of water-based Ag nanofluids. Finally we compare the experimental results with both the Maxwell-Garnett model and Rayleigh scattering approximation model, and they demonstrate that the Rayleigh scattering approximation model is reasonably predict the extinction coefficient of Ag nanofluids using hydraulic diameter of silver nanoparticle.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6C
• /
• pp.251-258
• /
• 2009

In this study, the optimum design conditions for embankment construction on soft clay layer improved by soil compaction pile (SCP) are discussed by comparing the practical design method to the reliability design which is based on the loss function and advanced first order second moment (AFOSM) method. The results are summarized as follows; 1) the relationship between safety factor and failure probability becomes heavy exponentially, failure probability decreases rapidly till 1% approximately until safety factor is smaller than 1.2 and after then, failure probability decrease gradually along the increase of the safety factor. The design safety factor of 1.2 may be the critical value that has been established on considering both relationships appropriately, 2) the safety factor of 1.15 at the minimum expected total cost is a little smaller than the design safety factor of 1.2 and the failure probability is about 1%, 3) the sensitivities of the ratio of stress share and the internal friction angle of sand is larger than the variables related the undrained shear strength of soft layer. This result means that the distribution characteristic of n and ${\phi}$ influences on the stability analysis considerably and they should be considered necessarily on stability analysis of embankment on soft layer improved by SCP, 4) new failure points of the input variables at the design safety factor of 1.2(below failure probability of 0.1~0.3%) is far 1~2 times of standard deviation from the initial design values of themselves.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.6
• /
• pp.20-31
• /
• 2005

Three dimensional Monte-Carlo simulations of non-ergodic transport of a lion-reactive solute plume by steady-state groundwater flow under a uniform mean velocity in isotropic heterogeneous aquifers were conducted. The log-normally distributed hydraulic conductivity, K(x), is modeled as a random field. Significant efforts are made to reduce tile simulation uncertainties. Ensemble averages of the second spatial moments of the plume and plume centroid variances were simulated with 1600 Monte Carlo runs for three variances of log K, ${\sigma}_Y^2=0.09,\;0.23$, and 0.46, and three dimensionless lengths of line plume sources normal to the mean velocity. The simulated second spatial moment and the plume centroid variance in longitudinal direction fit well to the first order theoretical results while the simulated transverse moments are generally larger than the first order results. The first order theoretical results significantly underestimated the simulated dimensionless transverse moments for the aquifers of large ${\sigma}_Y^2$ and large dimensionless time. The ergodic condition for the second spatial moments is far from reaching in all cases simulated, and transport In transverse directions may reach ergodic condition much slower than that in longitudinal direction. The evolution of the contaminant transported in a heterogeneous aquifer is not affected by the shape of the initial plume but affected mainly by the degree of the heterogeneity and the size of the initial plume.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.7 no.2
• /
• pp.33-42
• /
• 1970

This report is concerned with the fahrication with the falricationof silicon VVC diode by the double diffusion planer technique. At first, some design charts for VVC diode were derived by considering the voltage-capacitance relations, the critical field intensity at the metallurgical junction, and the cut-off frequency of the diode. These charts enables the fabrication engineers to design VVC diode easily without going into the sophisticated design theory. We started with a 2.5 ohm-cm n-type epitaxial silicon wafer. The phosphorous was diffused by POCl3 impurity source. Then boron diffusion followed make hyperabrupt p-n junction by BN source. The maximum to minimum capacitance ratio of the diode as a tuning diode for a TV tuner made in these experiments was 4:1. Measured electrical characteristics of the sample diodes showed in good agreement with the theoretical expectations. Slicing and polishing technique of the silicon wafer and diffusion technique of the impurity atoms, which were employed in our study, are also stated briefly in this report.

• Journal of KIISE:Computer Systems and Theory
• /
• v.29 no.6
• /
• pp.307-317
• /
• 2002

In this paper we propose a new mesh reconstruction scheme that produces a displaced subdivision surface directly from unorganized points. The displaced subdivision surface is a new mesh representation that defines a detailed mesh with a displacement map over a smooth domain surface, but original displaced subdivision surface algorithm needs an explicit polygonal mesh since it is not a mesh reconstruction algorithm but a mesh conversion (remeshing) algorithm. The main idea of our approach is that we sample surface detail from unorganized points without any topological information. For this, we predict a virtual triangular face from unorganized points for each sampling ray from a parameteric domain surface. Direct displaced subdivision surface reconstruction from unorganized points has much importance since the output of this algorithm has several important properties: It has compact mesh representation since most vertices can be represented by only a scalar value. Underlying structure of it is piecewise regular so it ran be easily transformed into a multiresolution mesh. Smoothness after mesh deformation is automatically preserved. We avoid time-consuming global energy optimization by employing the input data dependant mesh smoothing, so we can get a good quality displaced subdivision surface quickly.