• 한국세라믹학회지
• /
• 제32권2호
• /
• pp.227-233
• /
• 1995

By using homestyle microwave oven, Al-Al2O3 powder mixture could be oxidized and sintered into Al2O3 body. The differences in powder characteristics among the differently processed raw materials affect the oxidation and sintering behaviours, and these effects were more pronounced in case of microwave oven than of conventional furnace. Al-Al2O3 powder mixture was oxidized and sintered within 2hrs, which could save both processing time and energy.

• 한국분말재료학회지
• /
• 제19권3호
• /
• pp.196-203
• /
• 2012

$TiO_2$ was successfully formed on a Ti specimen by MAO (Micro-Arc-Oxidation) method treated in $Na_3PO_4$ electrolyte. This study deals with the influence of voltage and working time on the change of surface microstructure and phase composition. Voltage affected the forming rate of the oxidized layer and surface microstructure where, a low voltage led to a high surface roughness, more holes and a thin oxidized layer. On the other hand, a high voltage led to more dense surface structure, wider surface holes, a thick layer and fewer holes. Higher voltage increases photocatalytic activity because of better crystallization of the oxidized layer and good phase composition with anatase and rutile $TiO_2$, which is able to effectively separate excited electrons and holes at the surface.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.12-13
• /
• 2006

$Ga_2O_3$ is associated with the fabrication of thin window layer of solar cell. Usually, $Ga_2O_3$ is synthesized from Ga-metal oxidation method and GaN mono-crystal heat treatment method. We synthesized $Ga_2O_3$ powder using two methods and analyzed powder using latter method compared with powder by former method. XPS, XRD, IR analysis are conducted. XPS result, surface of GaN powder is almost oxidized to $Ga_2O_3$ at $1124^{\circ}C$ heat treatment and XRD and IR result, the inside of GaN powder is dramatically oxidized at $1124^{\circ}C{\sim}1300^{\circ}C$.

• 한국세라믹학회지
• /
• 제40권5호
• /
• pp.410-414
• /
• 2003

Characteristics of $UO_{2+x}$ powders oxidized at different temperatures were examined. Pellets were fabricated by adding these oxidation powders and their properties were also investigated. Particle size of the $UO_{2+x}$ powders decreased with increasing oxidation temperature while surface area increased. Only the powders oxidized at 35$0^{\circ}C$ enhanced the strength of green pellet. However, 35$0^{\circ}C$ oxidized powders added pellet had many surface defects. The difference of shrinkage rate between the oxidized and UO$_2$ powders was thought to be the cause of them.

• 한국건축시공학회지
• /
• 제23권5호
• /
• pp.547-558
• /
• 2023

초고강도 콘크리트의 강도와 유동성 확보를 위해 실리카흄(SF)를 사용하는 전통적인 방식에서 벗어나 산화 그래핀 나노플레이트릿(Oxidized graphene nanoplatelet, GO)와 유공유리분말( Hollow glass powder, HGP)를 사용한 초고강도 콘크리트를 개발하였고 본 연구에서는 자기수축 특성에 대해 검토하였다. 그 결과 SF를 사용한 Ref 배합보다 SF를 사용하지 않고 cGO(C사의 GO)와 HGP를 사용한 NewMix 배합의 자기수축이 13% 정도 감소하였다. NewMix의 자기수축에 의한 균열발생은 Ref 보다 1일 정도 지연되었고 균열발생 시의 인장응력은 가장 높았다. cGO의 높은 비표면적과 우수한 분산성으로 콘크리트 내의 공극들이 충전 되어 자기수축이 감소하고 cGO에 의한 균열저항 성능이 증가하여 초고강도 콘크리트의 자기수축 균열 제어에 효과가 있을 것으로 판단된다.

• 한국표면공학회지
• /
• 제51권2호
• /
• pp.104-109
• /
• 2018

Fe-2 wt.%Ni alloys were fabricated by metal powder injection molding, and their oxidation behavior at $600-700^{\circ}C$ for 30 h in air was studied in order to find the effect of the small addition of Ni in the iron matrix on the high-temperature oxidation. Oxide scales that formed after oxidation consisted primarily of $Fe_2O_3$, where microscopic voids were scattered. Nickel was segregated initially at the scale/matrix interface, and later at the lower part of the $Fe_2O_3$ scale. At $600^{\circ}C$, Fe-2wt.%Ni alloys oxidized parabolically initially, and linearly after 15 h. At $650-700^{\circ}C$, they oxidized linearly from the initial period. Although Fe-2wt.%Ni alloys oxidized slower than pure iron, their oxidation rates were relatively fast.

• Journal of Welding and Joining
• /
• 제19권5호
• /
• pp.481-485
• /
• 2001

Laser cladding processing allows rapid transfer of heat to the material being processed with minimum conduction into base metal. The effect of $CO_2$ laser cladding with high viscosity mixed powders was investigated. High viscosity mixed powder consists of bronze powder and flux that is used at a high temperature condition. The mixed powder has a high viscosity that it can be easily pasted over a curved or slope substrate. The device for mixed powder was designed and manufactured. It consists of the high viscosity mixed powder feeding system, the preheating system and the shielding gas system which prevents the clad layer from being oxidized. The results of experiment indicated that the feed rate of high viscosity mixed powder was important for later cladding with mixed powder feeding. The high viscosity mixed powder and substrate must be preheated to prevent porosity from breaking at the clad layer. The experimental result shows that the high viscosity mixed can be applied for laser cladding process.

• 한국분말재료학회지
• /
• 제3권2호
• /
• pp.91-96
• /
• 1996

The effect of vacuum annealing on the oxidation behavior of milled WC-15%Co powder mixture has been studied. A cobalt component in the milled powder mixture was oxidized preferentially above 175$^{\circ}C$ in air. The specimens showed a steady increase in weight at 175$^{\circ}C$ but did constant weight followed by rapid increase in specimen weight at the beginning above 20$0^{\circ}C$. Oxidation of the milled powder mixture was significantly suppressed by vacuum annealing at 30$0^{\circ}C$ for 10 h. Suppression of oxidation by vacuum annealing and different oxidation behaviors of the milled powder mixture between 175$^{\circ}C$ and 20$0^{\circ}C$, were attributed to removal of strain energy stored in the cobalt powder during vacuum annealing or oxidation treatment above 20$0^{\circ}C$. The role of stored strain energy on oxidation of milled WC-15%Co powder mixture was proved by X-ray diffraction method and differential thermal analysis.

• 한국분말재료학회지
• /
• 제18권6호
• /
• pp.575-582
• /
• 2011

MAO(Micro-Arc Oxidation) method was used to make $Al_2O_3$ surface on 6063 Al specimen. This study was focused on an influence of voltage, density of electrolyte and a period of treatment on the change of surface microstructure by using SEM(Scanning Electron Microscope), EDS(Energy Dispersive X-ray Spectroscopy). The microstructure shows higher roughness and thicker oxidized layer with increase of voltage and maintaining period of treatment. The density of electrolyte affected a formation of more dense surface and increase of a oxidized layer.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.355-356
• /
• 2006

WC-TiC-TaC binderless cemented carbide was oxidized under low partial pressure of oxygen (50ppm) at 873K for 1 to 20 h. Surface roughness was measured using atomic force microscope, and effect of TiC amount on oxidation behavior of the carbide was investigated. WC phase was oxidized more easily than WC-TiC-TaC solid solution phase. With an increase in TiC amount, WC-TiC-TaC phase increased and the oxidation resistance of the carbide increased.