• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.101-101
• /
• 2010

ZnO shows a direct band gap of 3.37eV, large exciton binding energy (~60 meV), high oxidation ability, high sensitivity to many gases, and low cost, and it has been used in various applications such as transparent electrodes, light emitting diodes (LEDs), gas sensors and photocatalysts. Among these applications ZnO as photocatalyst has considerably attracted attention over the past few years because of its high activities in removing organic contaminants generated from industrial activities. In this research, ZnO nanoparticles were synthesized by spray-pyrolysis method using the zinc acetate dihydrate as starting material at synthesis temperature of $900^{\circ}C$ with concentration varied from 0.01 to 1.0M. The physical and chemical properties of the synthesized ZnO nanoparticles were examined by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Fourier Transformation Infrared (FT-IR), and UV-vis spectroscopy. The Miller indices of XRD patterns indicate that the synthesized ZnO nanoparticles showed a hexagonal wurtzite structure. With increased precursor concentration, a primary, secondary particle sizes of ZnO nanoparticles increased by 0.8 to $1.5{\mu}m$ and 15 to 35nm, and their crystallinity was improved. Methyleneblue (MB) solution ($1{\mu}M$) as a test comtaminant was prepared for evaluating the photocatalytic activities of ZnO nanoparticles synthesized in different precursor concentration. The results show that the photocatalytic efficiency of ZnO nanoparticles was gradually enhanced by increased precursor concentration.

• 한국습지학회지
• /
• 제17권2호
• /
• pp.155-162
• /
• 2015

정수처리공정에서 미량유기물질과 맛 냄새물질인 2-methylisoborneol (2-MIB)와 geosmin의 제거특성을 파악하기 위하여 오존 및 advanced oxidation process (AOP)와 입상활성탄으로 구성된 biological activated carbon (BAC)공정과 활성탄 단독공정인 granular activated carbon (GAC)공정에 대한 pilot plant를 수행하였다. 운전 결과, 2-MIB 159 ng/L, geosmin 371 ng/L의 고농도에서 오존 1.0 mg/L 주입시 42%, 86%의 제거율을 나타냈으며 $H_2O_2$ 0.5 mg/L를 추가주입한 AOP 공정에서 각각 58%, 90%의 제거율 상승을 나타냈다. 또한 BAC공정에서 99.8%의 제거율을 나타냈으며 GAC 공정에서 2 ng/L이하의 처리성능을 보였다. 따라서 미량유기물질 및 맛 냄새 물질의 지속적인 제거를 위해서는 오존/AOP와 활성탄의 처리효과를 조합한 BAC 공정이 효과적으로 나타났으며, 활성탄지의 흡착능을 지속적으로 유지하기 위해서 유입농도에 따른 오존/AOP 공정의 최적화가 필요한 것으로 판단된다.

• 한국재료학회지
• /
• 제21권11호
• /
• pp.596-603
• /
• 2011

The very high temperature gas reactor (VHTR) is one of the next generation nuclear reactors for its safety, long-term stability, and proliferation-resistance. The high operating temperature of over 800$^{\circ}C$ enables various applications with high energy efficiency. Heat is transferred from the primary helium loop to the secondary helium loop through the intermediate heat exchanger (IHX). The IHX material requires creep resistance, oxidation resistance, and corrosion resistance in a helium environment at high operating temperatures. A Ni-based superalloy such as Alloy 617 is considered as a primary candidate material for the intermediate heat exchanger. In this study, the microstructures of Alloy 617 crept in pure helium and air environments at 950$^{\circ}C$ were observed. The rupture time in helium was shorter than that in air under small applied stresses. As the exposure time increased, the thickness of outer oxide layer of the specimens clearly increased but delaminated after a long creep time. The depth of the carbide-depleted zone was rather high in the specimens under high applied stress. The reason was elucidated by the comparison between the ruptured region and grip region of the samples. It is considered that decarburization caused by minor gas impurities in a helium environment caused the reduction in creep rupture time.

• 상하수도학회지
• /
• 제12권4호
• /
• pp.86-96
• /
• 1998

In this study, an intermittently aerated activated sludge process, modified process from conventional activated sludge process, was developed to treat high strength swine wastewater, which has been blamed as major pollutant for stream pollution. Therefore, the optimum cycle for oxic and anoxic period, SRT, and OLR were studied as design parameters. The effects of different time interval for oxic and anoxic period on nitrification and denitrification were examined by operating two reactors with 60/60min and 60/90min as oxic/anoxic period. Although the reactor with 60/60min showed complete denitrification of $NO_x-N$ generated during oxic period, the reactor with 60/90min showed incomplete nitrification due to the inactivity of nitrifier by accumulated $NH_3-N$ toxicity during anoxic period. Therefore, it is recommended to operate same interval for oxic and anoxic period. In order to determine the optimum cycle for oxic/anoxic period, four different reactors with 30/30, 60/60, 90/90 and 120/120min were examined. The reactor operation with 90/90min was optimum to get the most stable results in this study. However, the optimum cycle for oxic and anoxic period should be changed with characteristics of influent wastewater and operating conditions. According to lie operation results of three reactors with SRT of 15, 20 and 30days. The reactor with 2Odays SRT showed best removal efficiency of T-N. The optimum OLR would be $2.5Kg\;COD/m^3/day$ which showed the most stable nitrification and denitrification. Since characteristics of influent wastewater in the real system has a severe fluctuation, so it is very difficult to determine each interval for oxic and anoxic period. Therefore, ORP curves, describing the change of oxidation/reduction potential in reactor, can be used as a control parameter for automatic control of oxic and anoxic period. In other words, bending point (Nitrate Knee) of ORP curve during anoxic period could be used as a starting point of oxic period.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.179-182
• /
• 2006

The effect of electron beam irradiation on dye sensitized solar cell (DSSC) has been studied to examine degradation of DSSC. The high-energy electron beam irradiation affects on the materials and performance of dye sensitized solar cells. We have checked the effects of electron beam irradiation of $TiO_2$ substrate with and without dye adsorption on the photovoltaic performances of resulting DSSCS and also studied the structural and electrical properties of polymers after irradiation. All solar cells materials were irradiated by electron beams with an energy source of 2MeV at different dose rates of 60 kGy, 120 kGy 240 kGy and 900 kGy and then their photoelectrical parameters were measured at 1 sun $(100 mW/cm^2)$. It was shown that the efficiency of DSSC was decreased as increasing the dose of e-beam irradiation due to lowering in $TiO_2$ crystallinity, decomposition of dye and oxidation of FTO glasses. On the other hand, the performance of solid-state DSSC with polyethylene oxide based electrolyte was improved after irradiation of e-beam due to enhancement of its conductivity and breakage of crosslinking.

• Preventive Nutrition and Food Science
• /
• 제1권1호
• /
• pp.111-116
• /
• 1996

Polyphenol oxidase(PPO) isolated from the crude extract of ascidian, Halocynthia roretzi, showed higher affinity for catechol than tyrosine or DL-DOPA. Successful enzyme assay could be performed at $25^{\circ}C$, 10min. by mixing 0.2ml of crude enzyme extract with 2.8ml of 0.13M catechol in 0.1M sodium phosphate buffer(pH 6.4). The specific activity of PPO which had been purified with a combination of ammonium sulfate treatment, ion exchange chromatography on DEAE-cellulose, and gel filtration on Sepharose 6B was 13-fold disc gel electrophoresis. The activity of PPO was stable from pH 5.0 to 8.0 and showed the peak activity at pH 6.4 .The optimum reaction temperature for PPO oxidation on catechol was 35$^{\circ}C$ and those enzyme were heat stable up to 4$0^{\circ}C$. Molecular weigth of the enzyme was estimated about 170kDa. One molecule was found to be composed of gour subunits. Two of them had molecular weigh of 55kDa and the others 30kDa. The {TEX}$K_{m}${/TEX} values, {TEX}$V_{max}${/TEX} and catalytic efficiency({TEX}$V_{max}${/TEX}/{TEX}$K_{m}${/TEX}) for catechol were 0.12mM, 2.5mM/liter/min. and {TEX}$0.18min^{-1}${/TEX} respectively. The substrate affinity and electrophorectic pattern suggested that the enzyme of ascidian was considered to be not tyosine but catechol oxidase.

• Asian-Australasian Journal of Animal Sciences
• /
• 제32권12호
• /
• pp.1933-1941
• /
• 2019

Objective: This study was conducted to evaluate quality characteristics of cured pork loin with natural nitrite source from Swiss chard. Methods: Pork loin was cured in brine and the ratio of water and fermented Swiss chard (FSC) solution in the brine was changed by 4:0 (control), 3:1 (T1), 1:1 (T2), 1:3 (T3), 0:4 (T4), and pickled samples with 0.012% sodium nitrite (PC, positive control) and nitrite free brine (NC, negative control) were considered as the control. Results: The pH values of cured pork loins with FSC were decreased with increasing addition level of FSC. Cooking loss was not significantly different among all treatments. T4 had the lowest value in moisture content and lightness value and the highest value in curing efficiency. The redness value of T4 was not significantly different from that of PC in raw. After cooking, however, it was higher than that of PC. The yellowness value of cured pork loin added with FSC was increased with increasing level of FSC. Volatile basic nitrogen content of cured pork loin added with FSC was higher than PC and NC. Thiobarbituric acid reactive substance value of cured pork loin added with FSC was decreased with increasing FSC level. Residual nitrite level and shear force were increased with increasing FSC level. In the sensory evaluation, sensory score for flavor, off-flavor, chewiness, juiciness, and overall acceptability were not significantly different among all treatments. However, sensory score for color was increased when the concentration of FSC added to pork loin was increased. Conclusion: The FSC solution had a positive effect on redness and lipid oxidation. As shown by the results in protein deterioration and sensory, Swiss chard can replace sodium nitrite as natural curing agent.

• Macromolecular Research
• /
• 제17권11호
• /
• pp.863-869
• /
• 2009

The effect of a multiwalled carbon nanotube (MWCNT) dispersion on the electrical, morphological and rheological properties of polycarbonate (PC)/MWCNT composites was investigated, with and without pretreating the MWCNTs with hydrogen peroxide oxidation and lyophilization. The resulting PC/treated MWCNT composites showed higher electrical conductivity than the PC/untreated MWCNT composites. The morphological behavior indicated the treated composites to have greater dispersion of MWCNTs in the PC matrix. In addition, the electromagnetic interference shielding efficiency (EMI SE) of the treated composites was higher than that of the untreated ones. Rheological studies of the composites showed that the complex viscosity of the treated composites was higher than the untreated ones due to increased dispersion of the MWCNTs in the PC matrix, which is consistent with the electrical conductivity, EMI SE and morphological studies of the treated composites. The latter results suggested that the increased electrical conductivity and EMI SE of the treated composites were mainly due to the increased dispersion of MWCNTs in the PC matrix.

• 유기물자원화
• /
• 제27권2호
• /
• pp.51-56
• /
• 2019

황화수소는 매립가스와 바이오가스 사용 전에 제거해야 하는 유해한 불순물이다. 본 연구에서는 공기 산화를 활용한 황화수소 저감 방법을 연구하였다. C시 매립장에서 발생하는 매립가스의 유량 조절이 가능한 실규모 황화수소 저감 장치를 운전하였다. 실험 결과, 세정액 내 용존 철 농도는 황화물 산화 효율에 유의한 영향을 미쳤다. 매립지 발생 침출수 내 철 성분은 매립가스 내 황화수소 제거를 위한 용도로 철킬레이트와 혼용할 수 있었다. 철 농도가 90 mM 이상인 경우 9 초 이내의 접촉 시간에서 83 % 이상의 $H_2S$가 제거되었다. 따라서 촉매 산화 흡착법은 매립가스 및 바이오가스 정제를 위한 용도로서 충분히 가치가 있는 것으로 판단되었다.

• 한국분무공학회지
• /
• 제23권4호
• /
• pp.175-184
• /
• 2018

Emission characteristics of regulated (NOx, PM, CO, NMHC) and unregulated (VOCs, aldehydes, PAHs) air pollutants were investigated for diesel heavy duty buses equipped with different after-treatment systems (DPF+EGR and SCR) under urban driving cycle. The combustion temperature and the working temperature of SCR catalysts were important to make impact on NOx emissions, whereas PM emissions were low. The alkane groups dominated NMVOCs emissions, making 42.6~59.4% of sum of the NMVOCs emissions. Especially, alkane emissions of DPF+EGR-equipped vehicle included DOC had 14.9~15.5% higher than those of SCR-equipped vehicle due to low efficiency of oxidation catalyst. In the case of individual NMVOCs, n-nonane and propylene emissions highly occupied for DPF+EGR and SCR, respectively. Formaldehyde emissions among aldehydes were the highest and PAHs emissions were hardly detected except naphthalene and phenanthrene. The NMHC speciation has been shown to be the highest of the formaldehyde ranged 20.8~21.5%. The results of this study will be contributed to establish Korean HAPs emission inventory for automobile source.