• Environmental Engineering Research
• /
• 제11권6호
• /
• pp.318-324
• /
• 2006

The higher valence state of iron i.e., Fe(VI) was employed for the oxidation of one of an important toxic ion, cyanide in the aqueous medium. Cyanide was oxidized into cyanate, which is 1,000 times less toxic to cyanide and often accepted for its ultimate disposal. It was to be noted that Fe(VI) is a very powerful oxidizing agent and can oxidize most of the cyanide within few minutes i.e., ca 5 mins of contact. The data was obtained by the UV-Visible measurements for the Fe(VI) decomposition. The UV-Visible data was used to evaluate the overall rate constant for second order redox reaction between ferrate(VI) and cyanide. Also the pseudo first order rate constant was calculated as keeping the cyanide concentration in excess.

• Bulletin of the Korean Chemical Society
• /
• 제27권4호
• /
• pp.489-494
• /
• 2006

Goethite, hematite, magnetite and synthesized iron oxide are used as catalysts for Fenton-type oxidation of phenol. The synthesized iron oxides were characterized by X-ray diffraction (XRD), BET, X-ray photoelectron spectroscopy (XPS), and electron paramagnetic resonance (EPR). The catalytic activity of these materials is classified according to the observed rate of phenol oxidation. The effectiveness of the catalysts followed the sequence: ferrous ion > synthesized iron oxide >> magnetite hematite > goethite. According to these results, the most effective iron oxide catalyst had the structure similar to natural hematite. The surface oxidation state of the catalyst was between magnetite and hematite (+2.5 ~ +3.0). Phenol degraded completely in 40 min at neutral pH (pH = 7). Soluble ferric and ferrous ions were not detected in the filtrate from Fenton reaction solution by AAS. The formation of hydroxyl radicals was confirmed by EPR.

• 분석과학
• /
• 제8권3호
• /
• pp.351-358
• /
• 1995

X-선 광전자 분광법을 이용해 산화처리 조건을 달리하여 제조한 $Nd_{14}Fe_{80}B_6$ 조성의 리본합금 표면에서의 산화거동을 조사하였다. 산화 초기 "as-received" 상태의 표면 가장 바깥층은 Nd가 Fe에 비해 더욱 빨리 산화가 일어나 주로 Nd 산화물로 형성되고 Fe는 내부에서 금속상태로 존재하였다. 산화처리 시간이 증가하면 "as-received" 상태에 비해 가장 바깥층에 Fe의 상대적 조성이 증가하기 시작하였으며 산화가 진행됨에 따라 표면에서 먼저 형성된 Nd 산화층을 통해서 점진적으로 Fe 산화층이 형성되는 것으로 나타났다. 산화가 더욱더 진행되면 산화막 바깥층에는 Fe의 상대적 조성이 Nd의 조성 보다 오히려 풍부해지며 Nd는 바깥층보다 산화층 내부에서 풍부해지는 층상구조 형태의 산화막을 형성하였다.

• 한국세라믹학회지
• /
• 제35권1호
• /
• pp.55-65
• /
• 1998

Ag-36.8a%Cu-7.4at%Ti 조성의 브레이징 합금을 Si3N4 기판위에 브레이징한 후 브레이징 합금의 산화거동을 대기중 400, 500, 600$^{\circ}C$에서 조사하였다. 브레이징 합금의 구성원소인 Ag는 산화되지 않고 Cu와 Ti가 산화되며, 산화거동은 포물선적 산화법칙을 따랐다. 브레이징 합금의 산화에 따른 활성화에너지는 80kj/ mol 으로서 소량 첨가된 활성원소인 Ti에 의하여 순수한 Cu의 산화시 활성화에너지보다 감소하였다. 산화 초기에 생성되는 외부산화물은 Cu이온의 외부확산에 의해 성장이 지배되는 Cu산화물로 구성되어 있었다. 산화기간이 경과함에 따라 외부산화물층 아래에서 Cu의 농도는 감소되고 Ag의 농도는 증가하는 농도구배가 발생하여, 브레이징 합금의 산화물은 Cu산화물층(CuO)/Ag잉여층/Cu산화물층(Cu2O)/Ag잉여층의 다층구조를 갖았다. 또한, 분위기중의 산소는 Cu산화물 및 Ag잉여층을 통해 브레이징 합금 내부로 확산되어 브레이징 합금내의 Ti와 반응하여 내부산화물 TiO2를 생성하였다.

• 한국재료학회지
• /
• 제33권2호
• /
• pp.77-86
• /
• 2023

High-temperature oxidation of a Ni-based superalloy was analyzed with samples taken from gas turbine blades, where the samples were heat-treated and thermally exposed. The effect of Cr/Ti/Al elements in the alloy on high temperature oxidation was investigated using an optical microscope, SEM/EDS, and TEM. A high-Cr/high-Ti oxide layer was formed on the blade surface under the heat-treated state considered to be the initial stage of high-temperature oxidation. In addition, a PFZ (γ' precipitate free zone) accompanied by Cr carbide of Cr₂₃C₆ and high Cr-Co phase as a kind of TCP precipitation was formed under the surface layer. Pits of several ㎛ depth containing high-Al content oxide was observed at the boundary between the oxide layer and PFZ. However, high temperature oxidation formed on the thermally exposed blade surface consisted of the following steps: ① Ti-oxide formation in the center of the oxide layer, ② Cr-oxide formation surrounding the inner oxide layer, and ③ Al-oxide formation in the pits directly under the Cr oxide layer. It is estimated that the Cr content of Ni-based superalloys improves the oxidation resistance of the alloy by forming dense oxide layer, but produced the σ or µ phase of TCP precipitation with the high-Cr component resulting in material brittleness.

• Journal of Microbiology and Biotechnology
• /
• 제27권1호
• /
• pp.141-148
• /
• 2017

The oxidation ditch (OD) is one of the most widely used processes for treating municipal wastewater. However, the microbial communities in the OD systems have not been well characterized, and little information about the shift of bacterial community during the startup process of the OD systems is available. In this study, we investigated the bacterial community changes during the startup period (over 100 days) of a full-scale OD. The results showed that the bacterial community dramatically changed during the startup period. Similar to the activated sludge samples in other studies, Proteobacteria (accounting for 26.3%-48.4%) was the most dominant bacterial phylum in the OD system, but its relative abundance declined nearly 40% during the startup process. It was also found that Planctomycetes proliferated greatly (from 4.79% to 13.5%) and finally replaced Bacteroidetes as the second abundant phylum in the OD system. Specifically, some bacteria affiliated with genus Flavobacterium exhibited remarkable decreasing trends, whereas bacterial species belonging to the OD1 candidate division and Saprospiraceae family were found to increase during the startup process. Despite of the bacterial community shift, the organic matter, nitrogen, and phosphorus in the effluent were always in low concentrations, suggesting the functional redundancy of the bacterial community. Moreover, by comparing with the bacterial community in other municipal wastewater treatment bioreactors, some potentially novel bacterial species were found to be present in the OD system. Collectively, this study improved our understandings of the bacterial community structure and microbial ecology during the startup of a full-scale wastewater treatment bioreactor.

• 한국분말재료학회지
• /
• 제13권5호
• /
• pp.327-335
• /
• 2006

In the development of new hydrogen absorbing materials for a next generation of metal hydride electrodes for rechargeable batteries, metastable Mg-Ni-based compounds find currently special attention. Amor phous-nanocrystalline $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ alloys were produced by mechanical alloying and melt-spinning and characterized by means of XRD, TEM and DSC. On basis of mechanically alloyed Mg-Ni-Y powders, complex hydride electrodes were fabricated and their electrochemical behaviour in 6M KOH (pH=14,8) was investigated. The electrodes made from $Mg_{63}Ni_{30}Y_7$ powders, which were prepared under use of a SPEX shaker mill, with a major fraction of nanocrystalline phase reveal a higher electrochemical activity far hydrogen reduction and a higher maximum discharge capacity (247 mAh/g) than the electrodes from alloy powder with predominantly amorphous microstructure (216 mAh/g) obtained when using a Retsch planetary ball mill at low temperatures. Those discharge capacities are higher that those fur nanocrystalline $Mg_2Ni$ electrodes. However, the cyclic stability of those alloy powder electrodes was low. Therefore, fundamental stability studies were performed on $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ ribbon samples in the as-quenched state and after cathodic hydrogen charging by means of anodic and cathodic polarisation measurements. Gradual oxidation and dissolution of nickel governs the anodic behaviour before a passive state is attained. A stabilizing effect of higher fractions of yttrium in the alloy on the passivation was detected. During the cathodic hydrogen charging process the alloys exhibit a change in the surface state chemistry, i.e. an enrichment of nickel-species, causing preferential oxidation and dissolution during subsequent anodization. The effect of chemical pre-treatments in 1% HF and in $10\;mg/l\;YCl_3/1%\;H_2O_2$ solution on the surface degradation processes was investigated. A HF treatment can improve their anodic passivation behavior by inhibiting a preferential nickel oxidation-dissolution at low polarisation, whereas a $YCl_3/H_2O_2$ treatment has the opposite effect. Both pre-treatment methods lead to an enhancement of cathodically induced surface degradation processes.

• Journal of Microbiology and Biotechnology
• /
• 제22권5호
• /
• pp.668-673
• /
• 2012

Biohydrogen production from organic wastewater by anaerobically activated sludge fermentation has already been extensively investigated, and it is known that hydrogen can be produced by glucose fermentation through three metabolic pathways, including the oxidative decarboxylation of pyruvic acid to acetyl-CoA, oxidation of NADH to $NAD^+$, and acetogenesis by hydrogen-producing acetogens. However, the exact or dominant pathways of hydrogen production in the anaerobically activated sludge fermentation process have not yet been identified. Thus, a continuous stirred-tank reactor (CSTR) was introduced and a specifically acclimated acidogenic fermentative microflora obtained under certain operation conditions. The hydrogen production activity and potential hydrogen-producing pathways in the acidogenic fermentative microflora were then investigated using batch cultures in Erlenmeyer flasks with a working volume of 500 ml. Based on an initial glucose concentration of 10 g/l, pH 6.0, and a biomass of 1.01 g/l of a mixed liquid volatile suspended solid (MLVSS), 247.7 ml of hydrogen was obtained after a 68 h cultivation period at $35{\pm}1^{\circ}C$. Further tests indicated that 69% of the hydrogen was produced from the oxidative decarboxylation of pyruvic acid, whereas the remaining 31% was from the oxidation of NADH to $NAD^+$. There were no hydrogen-producing acetogens or they were unable to work effectively in the anaerobically activated sludge with a hydraulic retention time (HRT) of less than 8 h.

• Asian-Australasian Journal of Animal Sciences
• /
• 제26권2호
• /
• pp.282-286
• /
• 2013

Many manufacturing processes damage the structure of meat products and this often contributes to lipid oxidation which could influence warmed-over flavor (WOF) in precooked beef that is reheated beef. Electrical stimulation causes contraction of muscles and improves tissue tenderization. The purpose of this study was to evaluate the rate of lipid oxidation or warmed-over flavor that could be affected by electrical stimulation of precooked roast beef after refrigerated storage and reheating. The results show that there was no significant difference between chemical compositions and cooking yields when comparing non-electrically stimulated and electrically stimulated roast beef. Moreover, electrical stimulation had no significant effect on oxidative stability and off-flavor problems of precooked roast beef as evaluated by thiobarbituric acid reactive substances (TBARS) and sensory test (warmed-over aroma and warmed-over flavor). However, there was an increased undesirable WOF and a decrease in tenderness for both ES and Non-ES treatments over refrigerated storage time. Electrical stimulation did cause reactions of amino acids or other compounds to decrease the desirable beef flavor in re-cooked meat.

• Bulletin of the Korean Chemical Society
• /
• 제35권5호
• /
• pp.1385-1390
• /
• 2014

Hydrofluoroethers (HFEs) are developed as a suitable for the replacement of environmentally hazardous CFCs and are termed as third generation refrigerants. One of the major products of decomposition of HFEs in the atmosphere is a fluoroester. The present study relates to the OH and Cl initiated oxidation of $CF_3C(O)OCH_2CF_3$ formed from the oxidation of HFE-356mff. The latter is used as a solvent in the industry and reaches the atmosphere without any degradation. Kinetics of the titled molecule has been studied at MPWB1K/6-31+G(d,p) level of theory. Single point energy calculations have been made at G2(MP2) level of theory and barrier heights are determined. The rate constants are calculated using canonical transition state theory. Tunnelling correction are made using one-dimensional Eckart potential barrier. The rate constant calculated during the present study are compared with the experimental values determined using relative rate method and FTIR detection technique.