• Tribology and Lubricants
• /
• v.10 no.4
• /
• pp.13-26
• /
• 1994

Effects of resin contents, number of carbonization, graphitization, sliding speed, and oxidation on friction and wear behavior of carbon/carbon composite materials were investigated. Friction and wear tests were carried out under various sliding conditions. An experimental setup was designed and built in the laboratory. Stainless steel disks were used as the counterface material. Friction coefficient, emperature, and wear factor were measured with a data acquisition system. Wear surfaces were observed by the scanning electron microscope. It has been shown that the average friction coefficient was increased with the sliding speed in the range of 1.43~6.10 m/s, but it as decreased in the range of 6.10~17.35 m/s. Specimens prepared by different numbers of carbonization. showed variations in friction coefficient and friction coefficient of the graphitized specimen was the highest. Friction coefficients depended on contribution of the plowing and adhesive components. As the number of carbonization was increased, wear factor was reduced. Wear factor of the graphitized specimens dropped further. In the case of graphitized specimens, sliding speed had a large influence on wear behavior. When the tribological experiments were conducted in nitrogen atmosphere, the wear factor was decreased to two thirds of the wear factor obtained in air. It is obvious that the difference was affected by oxidation. Results of friction and wear tests were applied to a neural network system based on the backpropagation algorithm. A neural network may be a valuable tool for prediction of tribological behavior of the carbon/carbon composite material if ample data are present.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.4
• /
• pp.199-205
• /
• 2002

TiN and TiAlN films were deposited on SKD 11 steel substrates by an arc ion plating (AIP) technique. The crystallinity and morphology for the deposited films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The mechanical properties of both films were investigated through the indentation, impact, and wear test. Those films fairly adherent to SKD 11 steel substrate, showed hardness values of 2300 $\pm$ 100kg/$\textrm{mm}^2$ and 3200 $\pm$ 100kg/$\textrm{mm}^2$ with a load of 25g, respectively. During impact test, TiAlN films showed much superior impact wear resistance to TiN films. It could be suggested that the TiN films was failed relatively by plastic deformation with oxidation during impact test, while TiAlN films was failed by brittle fracture and resisted the oxidation by the impact energy. The friction coefficient of TiAlN films became lower than that of TiN films at high sliding speed condition although it was higher than that of TiN films at low speed. Therefore, TiAlN films was suggested to be more advantageous than TiN films for high speed machining fields.

• Korean Journal of Exercise Nutrition
• /
• v.13 no.1
• /
• pp.51-57
• /
• 2009

The aim of this study was to investigate gene expression related with lipid metabolism and long chain fatty acid oxidation rates in the skeletal muscle by exercise. Sprague-Dawley rats were randomly divided into control (CON: n=7), high-intensity (HI-EX: n=7) and low-intensity exercise (LI-EX; n=7) groups. Rats in LI-Ex group were forced to run on the treadmill at the speed of 10m/min for 60 min. On the other hand, rats in the HI-Ex group were forced to run on the treadmill slope 0 at the speed of 25 m/min for 60 min. The palmitate oxidation rate of the RG was increased immediately and 1 hr after exercise in the HI-Ex group, and the HI-Ex group was higher than in the LI-Ex group in RG and WG. Expression of PPARα of the RG in HI-Ex groups was increased compared with control immediately after exercise. FAT/CD36 expression were not shown any significant effect by exercise. AMPK expression of the RG in the HI-Ex group was significently increased immediately after exercise compared with control. The change in CPT-1 expression of the RG in the HI-Ex group showed a similar pattern to that AMPK. In the summary, the gene expression of PPARα, AMPK and CPT1 that was related lipid metabolism was not significantly affected by low-intensity exercise, but effected by high-intensity exercise. In conclusion, exercise intensity and amounts might be have very important role to regulate gene expression related with metabolism.

• Tribology and Lubricants
• /
• v.12 no.1
• /
• pp.22-28
• /
• 1996

This study was undertaken to investigate the dry wear characteristics and mechanism of KP-4M steel for plastic molding against SKD 61 hardened by heat treatment. The wear test was carried out under different conditions such as sliding speed, contact pressure, sliding distance, with frictional tester of pin on disc type. The wear loss on variation of sliding speed was little in lower speed range below 0.5 m/sec and in higher speed range above 1.5 m/sec,'but wear loss was high in intermediate speed range. The critical sliding speed, which showed the maximum value of specific wear rate, became lower with increased contact pressure. Increasing the contact pressure, the critical sliding distance Lcr which the wear mechanism changes from severe wear to mild wear was increased due to the decrease of oxidation reaction velocity. Through this study we suggested a model of generation and elimination process of wear debris of KP-4M steel for plastic molding.

• Tribology and Lubricants
• /
• v.9 no.1
• /
• pp.38-44
• /
• 1993

The present study was undertaken to investigate the dry wear characteristics of die steel STD 11 for cold molding. The wear test was experimentally carried out under different conditions using a wear device, which was made in laboratory, and in which annular surfaces of wear testing specimens wear rubbed in dry sliding condition with varying the sliding speed, contact pressure, and sliding distance. The wear loss by variation of sliding speed was much in 0.3 m/sec and less in higher speed range above its sliding speed according to formation of the boundary lubrication film. The critical sliding speed with maximum value of the specific wear rate switched over to lower speed side according. as contact pressure increased. The critical sliding distance was increased with decrease in oxidation reaction velocity. The depth below subsurface showing maximum hardness (Hv) came out at the position, $60 \mu m$, of the maximum shear stress due to strain hardening.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.332-338
• /
• 1999

Surface hardening of plain carbon steel (SM$%C) by Laser are usually much finer and stronger than those of the base metals. The present study was undertaken to investigate the wear resistance and a processing parameters such as, power density, pulse width, defocusing distance, and molten depth for surface modification of plain carbon steel. The wear test was carried out under experimental condition using the wear test device, and in which the annular surfaces of wear test specimens as well as mating specimen of alumina ceramics(Al2O3) was rubbed in dry sliding condition. It is shown that molten depth and width depend on defocusing distance. The wear loss on variation of sliding speed was much in lower speed range below 0.2m/sec and in higher speed range above 0.7m/sec, but wear loss was little in intermediate speed range. It depends on oxidation speed and wear speed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.4
• /
• pp.34-38
• /
• 1997

This paper presents a joining method by using the silicon wafer in order to apply to joint to the 3-dimensional structures of semiconductor device, high-speed , high integration, micro machine, silicon integrated sensor, and actuator. In this study, the high atomic beam, stabilized by oxidation film and organic materials at the material surface, is investigated, and the purified is obtained by removing the oxidation film and pollution layer at the materials. And the unstable surface is obtained, which can be easily joined. In order to use the low temperatures for the joint method, the main subjects are obtained as follows: 1) In the case of the silicon wafer and the silicon wafer and the silicon wafer of alumina sputter film, the specimens can be jointed at 2$0^{\circ}C$, and the joining strength is 5Mpa. 2) The specimens can not always be joined at the room temperatures in the case of the silicon wafer and the silicon wafer of alumina sputter film.

• Journal of Welding and Joining
• /
• v.4 no.1
• /
• pp.32-39
• /
• 1986

This paper was studied about the influence of oxidized films on workability in cold pressure welding. In preceding studies, the principal foci of the studies about pressure welding were considered several factors(surface manufacturing methods, surface roughness, pressure welding speed and surface temperature). But the influence to the growth of oxidation have hardly known well. So the purpose of this paper consists in solving the question above and proposing the optimal states of the pressure welding. Therefore the results obtained is as the following; When the oxidation time is within about 2 minutes, the bonding strength is very good after surface manufacturing of the neighboring to be bonded. The more surfaces are fine the more bonding strength is excellent. Above all, the optimal condition of cold pressure welding is the state that the characteristic value is 38% with smooth surface and without oxidation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.187-194
• /
• 2002

This paper describes the experimental results on direct selective laser sintering of WC-Co mixture for rapid tooling. The experiments were carried out within an air, argon and nitrogen atmosphere. Coupons of single layer were sintered at various laser powers, scanning speeds and scan spacings. As the energy density (energy per unit scanned area) is increased, the thickness of coupons is increased. The main problem took place during sintering within an air atmosphere was severe oxidation of WC-Co mixture. As the laser power is increased and/or scanning speed is decreased, more severe oxidation occurred. Within an argon and nitrogen atmosphere the oxidation is reduced significantly. Experiments on multi-layer sintering were also carried out.

• Journal of the Korean institute of surface engineering
• /
• v.27 no.1
• /
• pp.45-53
• /
• 1994

A kinetic study on the electrodeposition of zinc-iron alloys onto a steel in chloride solutions has been car-ried out using a rotating disc geometry. The results show that the deposition rate was increased with electropotential, disc rotation speed and temperature, and consequently the rate was partly controlled by elec-trochemical reaction and partly by mass transport. The iron content of deposit was more increased with cell voltage than with disc rotating speed and temperature. During electrodeposition process, the addition of metal-lic zinc powder retards oxidation rate of $Fe^{2+}$.